The MIL light came on and I noticed the shifting P-D or P-R was hard. Checked the Transmission Fluid and noticed it was low. Topped it up, but still MIL is on and shifting hard still. I bought a OBD2 Scanner and it returns P0707 "Transmission Range Sensor Circuit Low Input". Should I try clearing the DTC? It's a drag because it's my wife's car and she's driving mine.
View 1 RepliesThis is what I get from the DTC .....
DTC P0705
Description : transmission range sensor circuit malfunction
State : History
I have done some google search on the above diagnostic trouble code P0705 and as i understood , it indicates that the Engine Control Module (ECM) has received an input error from the Transmission Range Sensor (TRS).
Since the check engine light illuminated two times (two separate occasion) then it turns off now; the ECM is actually receiving input signal from the TRS.
So that leads me to think that the TRS is actually working but the problem might be one of the following two:
1- Open or short in the TRS circuit?
2- Dirty transmission fluid.
What do you think the steps i should do first of all ? how would i check the transmission fluid since my vehicle has no transmission fluid dipstick. My driving condition would fall into "severe" category and it reached 60,000 miles now ...
My 1.5L 2000 Hyundai accent is reading p0342 code.(cmp sensor circuit low Input). I have changed out the sensor from a parts car and it's still reading this code. I've read it could be timing or an issue with the starter wiring.
View 3 RepliesMy check engine light is on. I got the code pulled at Advance Auto Parts. It is P0107 - MAP Sensor Circuit Low Input. I wanted to test the MAP sensor to see if it is bad. I couldn't find anything online that was Santa Fe or even Hyundai specific as far as testing procedures go. I know you can test the power wire, the ground wire, and the signal wire, from what I could tell from other places I've looked. I got 5ish volts from the power wire and 12ish volts on the ground wire, which is what I understand they should be. I don't have a vacuum pump at the moment, but testing the signal wire with no vacuum I got about 0.02 volts. From what I've read online, it should be around 5 volts, but I wasn't sure if all MAP sensors work the same way. Whether I'm doing this correctly and whether they think the sensor is bad?
View 5 RepliesNeed solving a P0172 code I had. I just pulled out the MAF sensor and cleaned it with a MAF Sensor Cleaner (at most auto parts stores). Worked like a charm and the code went away and the gas smell is gone too.
Now I have a new code - P0712. I have been extensively searching the web and cannot find any good information on how to resolve this issue - "P0712 Transmission Fluid Temperature Sensor Circuit Low Input" ...
I checked the fluid level and it is fine.
I have a 2005 Camry, 2.2 liter, 4 cylinders...
CEL/OBDII code P0141 - O2 Sensor Heater Circuit Malfunction
So I just bought this car 64k well maintained but cant get rid of the check engine light. Replaced downstream O2 sensor with no luck. As soon as I get home I'll check voltage @ connector. Lets test the O2 sensor connection and test the pins to make sure there is no break in the wires.
Check engine light is on, this is the code that came up when checked at OReillys, "P0113 Intake Air temperature sensor 1 Circuit high input". Earlier took it to repair shop, he did not give the code, some sensor needs to be changed (don't know if he came up with same code). He had erased the code but it came back on within minutes. Wanted to check if there is any cheaper way to fix this. This is a windstar van.
View 15 Replies2004 Sport Trac V6. Been having hard shifting and P0715: Input/Turbine Speed Sensor Circuit. Cleared the codes and still returns.
From my searches, readings and looking at the parts diagram. On the newer 5 speeds the sensor is the one on the inside of the tranny. This requires taking the entire tranny apart? Is there an external connector for the sensor that I can check or clean first? Replace this sensor. I know the older ones were mounted on top of the tranny. I think this one is mounted on the inside though.
I cleaned my k&n air filter on my 02 passat 1.8 turbo let it dry oiled it very lightly, and 50 miles later I get a check engine light on, pulled the code 16486 and it says Mass or Volume Air Flow Circ Low Input. Cleared the code put a frame in until I can get it filter. Why that would throw me that code, k&n oil gumming up my sensor??
View 2 RepliesI have a 2007 f-250 6.0 liter turbo diesel. I was pulling a trailer with a golf kart on it and was not in tow haul. I was going up a hill and it shot up into 5th gear. I pulled into my house and shut it off and refired it and it acted fine. I went on a little test drive to see if it was going to do it again before I went on my trip. As soon as it shifted into third gear the tow haul light started to flash on my dash and went to 5th gear and would not down shift even if I did it on the column.
I scanned the truck with my snap on modus and it gave me these codes. P0706-transmission range sensor A circuit range/performance, P0707-transmission range sensor A circuit low input, and P1702-transmission range sensor circuit intermittent. I put a transmission harness in it and started it up and it ran fine and the codes were gone. I went for a test drive around the neighborhood and as soon as it hit 3rd gear it did the same thing as before. Today I put the old one back in and checked the codes so I could write them down and there weren't any so I went for a drive and it shifted through all the gears great and downshifted fine as well.
I pulled into my drive way to check for codes once again and there weren't any. I was gonna go for a ride in tow haul to see if it would do it and as soon I put the truck in reverse it started to idle high and the tow haul light started to flash again. I put it in drive to pull back into my drive way and it immediately shifted into 5th gear and threw the same codes...
About 3 weeks ago, I purchased a 2001 Accent GL 4dr 5spd from a friend of mine. A few days later, the CEL came on. I went to O'Reilly and got the code pulled, it was for a cam sensor input LOW. I replaced the sensor and was on my way.
Yesterday after starting the car for the first time for a few days (I wasn't driving because it needed a clutch), the light came on. Has it gone bad again or is something causing the signal to be low? Maybe a low output on the alternator or low battery? The interior lights dim slightly when the brake pedal is applied while the car is running.
I have a problem with my sonata NF 2006 the check engine light turn on like 2 days ago and give me the p2128 code say Accelerator pedal Position Circuit - High Input something like that i cheek all the cable off the throttle body to the ecu and i don't see any cable broken how I can check the accelerator pedal sensor? I see in one page a texting the sensor whit a multi miter but was for santa fe and the cable don't have the same colors . I need the accelerator pedal cable diagram and i don't have it ....
View 2 RepliesI bought 2004 Toyota Camry LE 2.4 couple of months ago, Been running good with no issues , no check engine light . Today I had it detailed from the inside and got it clean at a shop , then took it and changed the transmission Oil at Jiffylube . after leaving the shop the engine light came on . I then took it to a local Auto car parts and had used a car diagnostics scanner to see what was the problem and this showed up P0705 Transmission Range Sensor . I deleted it , then while driving around town , it came back on . I live in Minnesota and it is very cold here, not sure if the cold weather have to do anything with it, but i doubt it. The car looks and seems to be running ok .
View 5 RepliesI have replaced the transmission Range sensor (with OEM) and it is adjusted correctly, however This did not clear the. Code P0705... I am stuck ....
View 1 RepliesGot a code of p0708 on 2003 ranger flex-fuel 3.0.. Which is I believe is Transmission Range (TR) sensor. Not sure where to find that on truck...
View 1 RepliesI bought late 98 F-250, 5.4 G, 4WD. OHad to replace the steering flange because they messed up the ignition cylinder and flange. Truck didn't run for 4 years. 249K miles, no history available. Got the engine running, no DTCs. D, 3, 2, 1 barely moved the truck forward but, R hauled butt in reverse. Checked transmission fluid it was good and clean.
Came back to it a few days later it threw a P0720 (output speed sensor circuit) and I have no reverse, park feels like it wants to move, R is neutral, N is forward, D is forward, 3 is forward, 2 is forward, 1 is forward. The N is full drive. I cleared the P0720 code after it came up and it has not returned. The instrument gauges work but the odometer display is intermittent. Linkage? Fluid? Sensor? Wires?
I have these two codes:
P0A37 - Generator temperature sensor circuit range/performance
P0A2B - Drive motor "A" temperature sensor circuit range/performance
2001 F250. I have had issues on other trucks where you get a funny-acting speedometer with a code that comes up as VSS (sensor on top of the rear differential)....And it shifted exact same way.
My new truck speedometer is totally fine and the ABS is on with codes:
C1158 Left front speed sensor coherency malfunction
C1155 Left front speed sensor input circuit malfunction
Shifts about the same way on the trucks with bad VSS.
Question is will a bad front speed sensor affect the way the trans shifts? Doesn't happen all the time. If you go slow it shifts smooth. If you pull off fast a barely noticeable jerk from 1-2 and 2-3....
CODE P0102 "Mass or Airflow circuit low input" That was the code and upon checking my records prior to storing it for the year. I installed a new IAC,MAF, Fuel Pump and lots of new hoses, PCV, Fuel injection regulator. The Vehicle has only 110K miles. Now here is the clincher, after doing just the fuel pump it ran perfect for at least 25 miles, perfect I say. When I shut if off I got the check engine light, and thus the code which led me to install the other stuff. Now after pondering the matter, seems that it acted in a similar way PRIOR to my doing anything but there was no code previously. Like maybe some strange electrical connection, or something.
View 1 RepliesI went to my local Autozone today to have a code read and get the freeze frame data. I got a code P0118, Engine Coolant Temperature Circuit High Input. I called the dealer but they are out of stock on the sensor. Would it be a problem to use an after market sensor? I'm just concerned about the quality and accuracy of the sensor.
View 5 RepliesEngine light is one for about a month and finally got an ODB II.
Today it reads the error code [b]P0118 which is [b]Engine Coolant Temperature Circuit High Input
The coolant sensor reads 45 C when the key is on "on" position at about 2:30 pm this afternoon and I start the engine about 2 mins the temp jumps to 68 C, are these some logical number?
Does it mean the bad temperature sensor and I need to replace it?