I have a 2007 Accent with 119K on it.
I wanted to replace the water pump and I was wondering if this can be replaced without removing the timing belt or the lower timing belt cover?
A mechanic has my car and replaced my timing belt and water pump....he said he had it running and then it sputtered out and wont start..i have never had a problem with this car. Just replacing before it went out.. he is missing something.
View 19 RepliesHow to change the timing belt and water pump on a 2006 2.0t passat?
View 3 RepliesI just replaced the timing chain and water pump on my 1999 K1500 5.7L. After spending several evenings and a few early mornings working on it, I get everything back together and go to start it up. It starts then immediately dies. After double checking that the CKP sensor, two plugs on breather, and a/c and alternator wires (these are all that I unplugged) are connected I try in one more time before coming in to work today.
Timing chain was installed with No. 1 at TDC and mark on cam at 12 o'clock position as stated in the Haynes manual for the truck. I did not remove or even touch the distributor since replacing the intake gaskets ~3 years ago. Will check to see if any codes are showing in the morning when I have my laptop at home.
So after saying "We don't work on that model" when I asked for a timing belt / water pump change (yup, they actually said that), I went in today to try and get a second key made since the guy I bought the Phaeton from only had 1. I do not have the little code. I was told that there was nothing they could do without the code. My only hope would be to contact EVE directly.
View 2 RepliesSo I was getting my car flashed to stage 1 at a dealership here in the Chicago suburbs and there was CSG R in there with the timing belt shredded. Turns out water pump came apart, shreded the timing belt, and apparently the pistons smashed the valves. I got a call from my friend whos a mechanic and said another one is getting towed there today with the same issue. Both have between 2k and 3k miles on them.
View 24 RepliesI replaced a timing belt and related parts on a v 6 atq motor and three weeks later there's a pretty good oil leak, where its from or if oil leak can be related to timing belt replacement... leak seems to be in same area as crank pulley but not sure...
View 2 Replies1987 Acura Integra AT with 158k... Water pump broke after 75k miles (in 18yr period)....
I am wondering what else should I have it done:
- thermostat
- oxygen sensor (is there one?)
- vacuum tubes (I hear that these fail due to age)
- anything else?
Are these near where they will be working on? Any other tips?
I have a 2002 Audi A4 1.8T with 85,000 miles. Recently my car started overheating, I replaced the water pump, thermostat, and timing belt. The mechanic also ran tests to make sure there were no issues with the head gasket, those tests came back saying the head gasket was a-ok. Yet, my car is still overheating but only on days when the outside temperature creeps above 90 and I am in stop and go traffic. I have to re-fill the coolant tank about once a week depending on how much I drive. I find no coolant puddles under my car when it is parked, so I do not believe it is leaking. What else could be causing my car to overheat?
View 2 RepliesI have a 2002 Intrepid ES with a 3.5L V-6 with 264,000 miles on it. I have recently had the timing belt and water pump changed. Three weeks later I am driving home and the temperature gauge starts climbing. This is the first time this car has ever overheated. Well, I call my buddy who is a certified mechanic and he tows the car to his shop. I have him check the water pump to make sure it hasn't prematurely failed. He tears the front of the engine down and inspects the pump. He finds nothing wrong with the pump but he discovers the timing belt tensioner has failed and it has caused the engine to jump time, I tell him to go ahead and replace the tensioner.
After he put the engine back together he started it and it ran cool while it was sitting at idle for about 45 minutes. Then he took it for a test drive and it overheated again. He checks the thermostat and finds that it has also failed; he replaces that also, still overheating. New radiator hoses, upper and lower, new radiator, new thermostat, new water pump and it still overheats. He put dye into the coolant to check for a blown head gasket and it tested negative for a blown gasket. The exhaust doesn’t smell of burning coolant or producing white smoke. My mechanic friend and I both have run out of solutions…
Toyota dealer said computer indicated the water pump and belt needed replacing. We decided to do the replacement ourself. Now the light comes on which indicates car is running hot. We did replace the coolant. The 2005 Toyota Prius never ran hot before the replacement, What did we do wrong?
View 3 RepliesI was driving my 2005 RX 330 (138k miles) North on I-75 through Atlanta in rush hour traffic when the car completely died in the left hand lane w/ no shoulder. GDOT stopped six lanes of traffic to push us up and over a couple of hundred yards to a right shoulder. It was determined that due to a coolant leak from the water pump the timing belt malfunctioned and shredded.
I had heard that the water pump should be replaced during the 90k maintenance when the timing belt is changed, but my water pump was not replaced according to my maintenance records. I understand from reading a couple of posts that this isn't always required but that they do check the water pump. Is this correct? And if so should they have noticed that there was a potential problem?
My audi runs great. Its has 170K miles on it. My mechanic replaced an air pump last Friday and by Monday I had a new issue. I noticed coolant leaking. I took it back to the mechanic who fixed the airpump to diagnose. He tells me that the leak is coming from the timing belt/water pump area and in order to get there it takes 7 hrs. He suspects that its the water pump or a cylinder block crack. He suspects it could be a water pump breakdown more than a block crack. A block crack could be a serious issue with the engine is what I suspect.
I think he did something wrong when he replaced the air pump. He tells me that these are in two different areas and that he canbe generous with his time in only diagnosis but not in fixing the problem. Do you think he is right ?
He recommends that when they open the timing belt cover its best to replace the belt, tensioners, water pump etc.. Now spending $ to get to know where the leak is sounds steep.
I had the timing belt, water pump and thermostat replaced on my '97 RAV4. The next morning while braking at a red light I heard a rapidly repeating sound that sounded like metal on metal. The car never made that sound again but now I'm hearing a noise coming from the passenger side of the engine (timing belt side). When the engine is cold I don't hear it. After driving a while its starts, then once the engine warms up it generally goes away (except for this morning which was the coldest morning since this started, temps in the 40s).
I was only hearing the noise when the car was stopped either in drive or reverse (reverse sounded louder) if I lightly let up on the brake pedal (there's no pulsing in the brake pedal). Once under way the sound goes away. This morning it was making the sound virtually every time I came to a stop (once the car warmed up) even with my foot firmly on the brake pedal. I recorded the sound Saturday while standing still with the car in drive and my foot slightly easing up on the brake pedal. The sound starts at the 20:30 mark, what it could be?
My car has 103000 miles on it and the timing belt was replaced several hundred miles ago. After the service I noticed it had a bit of a rough idle and a very slight sputtering noise, but still no check engine light. Was the timing belt put on wrong? The engine is non-interference, by the way.
View 1 RepliesRebuilt a motor due to the timing belt failing. Everything works except I can't get the timing to line up perfectly.
From what I'm getting from the service manual, line the camshaft sprocket with the mark visible from the hole
Line up the crankshaft gear with the yellow mark at the bottom.
Do I have to do a double/triple turn of the cam/cranks to get TDC to be achieved properly? My biggest problem on this car is having the crank gear shift a couple teeth after tensioning the belt.
The timing belt broke in my gf's '08 accent recently and I decided to have a crack at replacing the belt after getting a quote for $900 from the nearest mechanic (with no guarantee it would fix the problem).
When re-aligning the cam and crank to TDC, I wasn't sure if it mattered which revolution the crank was on (ie. 1st or 2nd revolution) when putting everything back together. I tested rotating the engine with the new belt on slowly to make sure there was no contact and everything seemed ok.
So basically now everything is back together, tried starting it up and it won't start and now i'm wondering if it would make a difference or not if the crank was rotated 1 additional revolution. Otherwise there is more significant damage.
In the process of rebuilding a 2007 Accent where the timing belt broke while idling.
Pulled the head, ran a "water test" on the valves (put spark plug in, pour water on the valves and see if it comes out the exhaust/intake side) and found that only 2 intake valves were belt. Also shut off all the lights in a pitch black room, shined a flashlight in the intake/exhaust and didn't see any light leak from any of the cylinders except the one with the 2 bent valves.
Does this make sense? I would assume since 2 cylinders are always TDC at once, at least 4 valves would be bent.
Lastly, before rebuild I'll be replacing the 2 intake valves, all the valve stem seals, intake manifold gasket, exhaust manifold gasket, head gasket, head bolts and valve cover gasket. Anything else I should replace on the head? Trying to keep costs down as much as possible.
To add: Pistons have no damage on them, there are no marks of the valves hitting the pistons. The timing belt was replaced after it broke and the engine still ran however it ran rough. Compression test was done on only cylinder 1&2, 1 had 60 PSI and 2 had 0 PSI. Compression test was also done by just rotating the crank with a socket since I already had some of the engine disassembled.
The timing belt went out at idle while making a turn. I changed the timing belt, but when cranked you have to pump the gas to keep it running and it is really rough running with a smell of gas when you turn it off. On the last run it backfired slightly. There is no knocking or pinging. And have triple checked the timing. Could improper torque on the crankshaft bolt cause this or failed ignition coils?
View 21 RepliesI was driving on the highway at about 80 mph when my car made a thunk noise and then the mph dropped to 40 mph. The car was hesitating but I continued to drive it to gas station. At this point steam was coming from passenger side engine front. The coolant was coming out now my car was overheating to the extreme. I drove it to shop. Next day he changed the thermostat and water pump. But he said it took him a while to get air out / bleeding it?! The day I drive off with my repaired car it still sounds loud eventually it sounds like a helicopter!!! Next day take it to Infiniti dealer they say I need a new engine. Internal engine failure! Could this have happened because the water pump wasn't replaced correctly? My car is a 2006 Infiniti G35x, 96k miles.
View 19 RepliesIs it possible to change the water pump and serpentine belt in a 2006 Toyota Camry with 4 cyl. engine in less than an hour?
View 4 Replies