Accent MC (2006-11) :: Buzzing Coming From Top Part Of Intake Manifold And Rough Idle
Apr 4, 2012
I was in the process of troubleshooting a quick to die battery tonight (ignition on and if you put a load on it like radio and headlights, a few minutes later it needs the booster pack. ) During this time I discovered a loud buzzing coming from the top part of the intake manifold (ignition on but engine not running.) As my battery drains, this noises this thing makes change. I started the car up and let it run for a sec, then back off/ignition back on and it stopped buzzing.
On a side note, the car has been idling like dump for the last month or so. Sometimes it's smooth as silk as it always has been when stopped at a light, other times you can feel a rapid vibration in the steering wheel, seats, and floor. To the point where stuff rattles sometimes. It's definitely at its worst when the engine is cold. I was hoping it was worn out plugs, but they've just been replaced and it still doesn't run right.
Linked is a video, hopefully it works. Is this the IAC valve?
View 9 Replies
Advertisement
Well my 39000 mile run of zero faults ended with a intake manifold failure. The check engine light came on whilst on a Yosemite trip, I checked fluids, etc, car was driving ok, but when I reached my destination I noticed a rough idle. Next time I started it a couple of days later the check engine light was flashing, and it was a rougher idle, so I knew enough not to drive it.
The closest dealer fixed it (no cost to me) under the power-train warranty (nice customer care from Michaels Fresno plus they had the parts in stock).
I learned a couple of things being stranded:
1) Problems happen but they can be accurately diagnosed and fixed.
2) $150 coverage for towing on my insurance policy doesn't get you very far. But I wanted to take it to VW to simplify any warranty work and have it repaired quickly, so I paid quite a bit of overage.
3) Tow trucks don't carry a family of 4, so the logistics of getting a rental car to get my family home wasn't simple.
4) If you have to be stranded, Yosemite valley with the free shuttles, is a pleasant place to be.
5) If you need a reminder just how good a car the Tig is to drive, just try renting a Jeep Compass for few days...
Diags for the record:
GFF found 9 faults: P0170, P0300, P0301, P0302, P0303, P0304, P0507, P068A, P2015. Found arm for intake runner flap came apart causing vacuum leak that caused engine misfires.
Parts
1 x 06J-133-201-AS Manifold
4 x 06J-998-907-B Repair Kit
View 8 Replies
OK, car has 94K miles, never had anything done to it, and the timing belt stripped out a bunch of teeth and bent the valves, you know the usual deal.
Pulled the engine apart, and order a head gasket set and scored a low miles head from a salvage yard. I was told the engine it came from was running fine but had a damaged timing cover so they parted out the engine, when i got the head the timing belt gear was bent and cracked, but i couldn't see any other damage and all looked good so i put it all in, and after having some trouble getting good info on where the timing marks are suppose to go i got it all back together and went to fire it up, start and die a couple times, i figured it was the fuel system re-priming itself, car starts and is running rough, i give it a few small revs and above about 2K it seems to run fine, but has def misfires at idle.
While i was looking around the engine bay checking over stuff i can hear a definite buzzing sound coming from the injectors, which i can tell you isn't normal, and is causing my problem i believe. The injector plugs are pretty straight forward, so im pretty sure i have them in the right spots.
The CEL came on, and i plugged in my code reader but was unable to connect to the ECM for some reason. Are these cars can bus?
View 16 Replies
I have an 01 Accent GL 1.6L. It will not turn over. Battery, terminals, and wires are all new. Alternator is also good. There is a buzzing noise coming from beside the cold air intake. I'm not sure what part that is. The part that is buzzing is where the cam position sensor is connected to. It also has wires that run into the firewall.
View 21 Replies
I am checking my car parameters at idle. I was comparing the values of intake manifold pressure and vacuum. When I press accelerator or give gas means throttle plate opening my manifold pressure decreases and vacuum increases, I hear when throttle plate open more air come inside so manifold pressure must be increases and vacuum decreases. Am I right? if so which part will be culprit of this action?
View 3 Replies
I have a chamfering noise coming from my intake manifold on idle. sometimes its there and sometimes its not, it goes away with any application of throttle.
View 9 Replies
I have a small clicking sound coming from my intake manifold. I recently installed a boost gauge and it did it once after that... I shut the car off and I didn't hear again until 1000 miles later and its back, why it would be clicking like this but its annoying
View 6 Replies
I have been having some issues with my 97 ford f150 4.6 liter, started out running rough, then hydrolocked with no serious damage, blown intake manifold gasket, fixed that, alternator over charging do to bad voltage regulator, fixed that. and airbag code 52, still working on that, as well as failure to connect when trying to do diagnostic scan. now I am wondering if the engine diagnostic is still even working. still running good just a very slight vibration when warms up. I am not getting any code. or my check engine light is not showing any codes. What I want to do is force a code. What would be the safest way to force a code or force engine light to give a code?
View 6 Replies
Need to know the part number to F Sport Cold Air intake for a 2006 GS300?
I have the car since day one and absolutely loved it since. Starting finally to a couple of Mods, recently installed a Strut Tower Bar, this weekend installing F-Sport Sway Bars (front and rear).
View 1 Replies
I have a 01 vr6 mk4 gti. When I bought the car I noticed a rattle but never paid mind to it. But now I just want it fixed. I hear the rattle come from the back of the engine near the intake manifold when I rev it a little. The most rpms the louder the rattle . I been doing some research and came to a conclusion that it could be the shift rod and bad intake bushing. But, I'll like a link on how to replace the shift rod.
View 5 Replies
2012 dodge caravan. Bought it used last year with 27k miles. Day after I bought it, it threw a misfire code. They said the spark plugs got wet when they washed the under carriage. Dried it out, cleared the code.
For the next month the car went from a slight shimmy during idle...progressed to strong shaking (its shakes, pauses, shakes...etc.) Finally another misfire code. Took it in and this is what the report says.
"Cylinder misfire on #4. Performed compression test found #4 cylinder compression at 100 PSI. All other cylinders at 150 PSI. Recommend to replace front cylinder head. Has burned exhaust valve seat. Replaced left cylinder head assembly."
About 2 months later check engine light comes on, car is over heating. Coolant bone dry. Replaced coolant, took it back in. They replaced the intake manifold?? Been slowly losing coolant. I have to replace it about every 2-3 months. I notice the car shakes worse when the coolant is low, with minimal shaking when coolant is replaced. Finally took it back in a few week ago when my husband got back from deployment. They said it was a loose bolt on the intake manifold causing the slow leak. They couldn't verify my complaint about the shaking.
Now, car still shaking. Its minimal on start up, gets worse the longer I idle. I can only feel the shaking while in idle. If I restart the car it goes back to minimal before progressing again. Took it back in. They verified the shaking, hooked it up to a computer, no codes or anything. Told me its normal. It CANT be normal, right? I neglected to check the coolant level before I took it back in. I left it with them saying they will look it over, but they don't think anything is wrong. This is exactly how it progressed when they ended up replacing the cylinder head. I have 1k miles left on the warranty, and am moving in 2 weeks 1500 miles away. I don't have time to wait for another code.
View 19 Replies
I have a 2003 Camry 4 cyl. around 60,000 miles on odometer and for around 3 months the engine seems to have gotten louder while at idle. At the back of the engine around the plastic intake manifold area the engine is making a light banging / tapping noise. It never made this noise before. The engine idles fine and the drives normally. I always keep an eye on the fluid levels and they are up to par. I'm not sure what is going on and if I should just keep an eye on it. I have provided a link below to a video of the noise. The noise can be heard best starting around 15 seconds into the video and fades away around 26 seconds into the video. [URL] ....
View 1 Replies
I have a 2003 Camry 4 cyl. around 60,000 miles on odometer and for around 3 months the engine seems to have gotten louder while at idle. At the back of the engine around the plastic intake manifold area the engine is making a light banging / tapping noise. It never made this noise before. The engine idles fine and the car drives normally.
I always keep an eye on the fluid levels and they are up to par. I'm not sure what is going on and if I should just keep an eye on it. I have provided a link below to a video of the noise. The noise can be heard best starting around 15 seconds into the video and fades away around 26 seconds into the video. [URL] .....
View 14 Replies
It makes a weird 'fppp' air shooting noise before the exhaust note and my 2003 gti vr6 makes the exact same noise. It sounds like it's coming from the intake manifold valve and not really the filter, but I'm not sure and yes my filter is clean, the noise also sounds a little bit more obnoxious and problematic in real life. What it is, I thought it was a vacuum leak but I don't wanna bring it in till i know exactly what it is,
View 2 Replies
I have a 2006 F150 screw 4.6 auto 116k miles that has evidence of a small coolant leak where the intake manifold joins the head. This is on the drivers side directly under the thermostat housing. The t-stat housing is dry and the hoses all appear dry. It's just wet right at the gasket where the manifold joins the head. Reservoir is still normal so it's not leaking too much just yet.
I searched this site and youtube but didn't find any other posts. Lots of problems with older trucks with composite manifolds but nothing for this one. It looks like a part of the bottom of the manifold is plastic but the entire top and where it is leaking is all aluminum.
It seems odd that this would start in the winter time just driving back and forth to work (no load). And, yes the antifreeze is good. Just wondering if this is a known issue with this truck. Is it just a matter of replacing the gaskets or is there some other flaw I should be concerned about?
View 2 Replies
My 2011 Hyundai Accent 1.6 runs fantastic and has since I purchased it three year's ago until two weeks ago when my domestic partners friend changed the spark plugs, oil, air filter and stuff so I could go on a short trip and back. About 200 miles into it I pulled into a rest stop and noticed it was rough before I put it in park. As soon as I put it in reverse it was running rough and sounded like it was going to die. Forty miles later the check engine light was on and it was running terrible. A parts store recommended different spark plugs. A nice man who was there overheard the conversation and offered to put them in for me since I know nothing about doing. He said he gapped the spark plugs at 0.40? When I started it it ran like a dream until about 75 miles later and it began doing it again but the light never came on. It is doing the same thing which is a rough idle when stopped but it smooths out when I put it in park.
View 3 Replies
I've had my 2010 Accent for about 9 months. It's got about 63K miles on it. Serviced regularly, no issues there. Yesterday while coming home from a road trip....6 hours there, heavy driving while in town, 6 hours back 2 days later, the check engine light came on the dash. I then noticed that the car was idling very rough. When I put it in gear after starting, I can visibly see the car the shake. Having major problems accelerating, I have to mash the gas to the floor to make it go. Shutting off the air conditioner seems to work a bit, but not totally.
I should note that I live in the South East US, it was over 95 degrees when we left town and the destination was over 100 the entire time we were there. I was told this could be vapor lock, but am not sure about what to do to clear that when the temps won't drop around here for some time. I took it to AutoZone this morning to have them read the codes on the check engine light and was told that their code reader was incompatible with my car.
View 2 Replies
I have a 2009 Accent and after about 20 minutes of driving it started running really rough and my check engine light came on. It's worse at an idle (feels like it's going to stall out) but isn't quite as bad when I rev it. My first thought is water in the gas tank since we've had a lot of rain for the past week or so and I filled it up a day or two ago.
View 2 Replies
I did not get the specific cel code but its what the guy told me at autozone.
Long story short. Washed engine, let sit for about 30 mins. Car started with flashing CEL and was "puttering" and very rough idle. Drove home took intake off and replace with stock, took spark plugs out and they were not wet. Then let it sit for about 15 mins. Started just fine. No CEL at all.
The accent saved the CEL and the guy told me that Cylinder 1 had a misfire.
My question is, should I do anything now even though the car seems to be running ok?
View 26 Replies
I have a 2008 Accent SE and I'm having some issues... The car was driving fine the other day all the sudden check engine light came on started flashing then and just stayed on. This happen before and the car was under warranty so the dealership fixed it but now it ran out and it's happening again. Anyway the car is running very rough at idle like the car shakes and acts like it doesn't want to run. Also when driving it honestly feels like the car has no power or acceleration what so ever. I replaced the air filter with a brand new K&N filter, I also changed the spark plugs today. I put NGK's in and the problem is still the same. I had it hooked to a code reader and it said I had a misfire in cylinder 2. I thought the plugs would have fixed it but I guess not.
View 9 Replies
I just bought a 2010 Accent for my daughter and this was the 2nd time I filled it up. I realize now I should not have topped it off all the way but I did. The tank was probably bone dry when I filled it up as well. Within 5 miles after I filled it up, it started running rough and the check engine light came on. I stopped it and checked around under the hood. Checked to make sure the gas cap was tight. I drove it again and it appeared to run fine. I stopped by an Autozone and had the code checked. It was a misfire code for cylinder 3.
Drove it home (10 miles) and parked it. I took the battery terminal off and cleared the CEL. When my wife drove it a few minutes later, the CEL came on again and it started running rough. Had the code checked again and the cylinder 3 code came back. The guy at Autozone said over-filling the tank when it was empty probably caused too much pressure on the fuel going into cylinder 3 and that it should correct itself in the next few days. I drove it 20 miles to work today without any problems. It seemed like it had to be related to filling up the tank since it happened a few minutes later.
View 3 Replies
