Accent MC (2006-11) :: After Replacement No Change Between Driving Lights And Low Beam
Dec 15, 2014
I have an accent 2006 GS Sedan. I bought this as used recently. Noticed that the lights are not powerful at nights. When I turn on the lights there is no changes in the power of the driving / low beam lights.
Whether this is the standard with accent 2006. Other vehicles I have with me changes the power of the light and in this case there is no changes at all. I bought extra powerful bulbs and put them and there was a slight change, but there is no change between the driving lights and the low beam.
View 4 Replies
Advertisement
Wanted to change my stock yellow high beam (DRL) bulb to an LED bulb i bought from jdmtoys I also changed the parking light to LED and it works perfectly, so after changing the high beam bulbs it worked for few seconds then stopped working... I put back the stock high beam bulbs and it still is not working did i blow a fuse or something? Now when I turn the high beam on my headlight turns on instead of the high beam....
This is the bulb i purchased : [URL] .....
View 14 Replies
Background: Sonata 2009 Limited. 165K Miles. Original factory installed everything. Chicago area.
Last week I drove to the mall in the snow. Headlights worked fine. Upon leaving the mall I realized that my low beam headlights were not working.
Purchased and installed one low beam headlight bulb, on the slim chance that both of them simply burned out at the same time. It didn't come on.
Results of an internet search indicated that the fuse might be blown. I pulled the 20amp Low Beam headlight fuse and sure enough it was bad. Put in a new fuse. Turned on the headlights and it blew instantly.
Have been driving with the high-beams the past 5 days. Only one car has "blinked" at me, so driving with the high-beams isn't a problem. Probably because there are so many cars with really bright low-beam headlights these days.
However, I would like some guidance to getting this problem resolved. What are the most likely reasons for the low-beam headlight fuse blowing instantly like this?
View 1 Replies
I installed a set of bi-Xenon HIDS identical to these.
in my wife's 2008 Accent. I unplugged the DRL module as shown in a thread I found here, but now there's no high beam indicator on the dash. Is there a wire on the plug that I can put a jumper on or something to make this work again?
And before all the nay-sayers growl at me, instead of assisting with this problem, I aimed the lights really low so there's minimal glare to oncoming traffic. We drove about 125 km last night with them and never got high-beamed once.
View 3 Replies
08 accent passenger headlight was noticed to not be operating while in low beam. Switched to high beam- it works, but still no low beam.
First instinct was replace the bulb. Low beam works but now.. high beam doesn't?? Bulbs are fine, brand new out of the box and driver's side works like a charm. Bright as heck... passenger's side isn't quite as bright If that's any relation to the problem.
Checked the fuses, they're all good. Made sure bulb was placed in secure. Filament didn't get bounced around either. Was poking around online and seems it could be the relay. Manual doesn't seem to list a relay for the headlights or am I not reading it right?
View 3 Replies
I bought a 2009 Accent last week after my 1987 Camry wagon bit the dust. It has 47000 km and seems to have been very well maintained. The only problem I have noticed is that the high beam indicator light does not come on, although the hi beams do work. I downloaded an owner's manual but am not sure which fuse the indicator light is on; in any case, everything else seems to be working so I expect the bulb is burned out. My problem : I don't know its location on the instrument panel since it has never worked, and I don't know if it is possible to replace it without special tools.
View 2 Replies
I have a 2012 Hyundai Accent GLS and recently noticed that my low beam only works in the high beam setting and the high beam doesn't work.
View 10 Replies
If you drive less than 6000 or maybe even less than 3000 miles a year, how often should one change the oil on the car? Or don't bother with time interval but mileage as recommended for the make and model? I'm not sure there's a recommendation for time on the make & model, I'll check sometime.
Car in question is a Hyundai Accent 2009
View 19 Replies
2006 Lexus GS300 AWD, My driver side low beam HID turns off at night while driving. Both lights come on, then after driving for about a few mins, the driver side low beam hid will go out. Then, if I quickly turn the lights off, and back on, it comes back on and stays on for another few mins. Repeat. Sometimes it will eventually stay on for the rest of the trip.
View 5 Replies
I have an '06 Camry, which has lost all power functionality. The follow items just stopped working
1. Key fob -- keyless entry and alarm stopped working
2. high beam doesn't come on when headlight is on. However, when headlight is off, it comes on--go figure
3. Power door lock also does not work, even from driver side door. Have to lock all doors manually
4. Interior lights don't come on when door is open.
View 4 Replies
It is a bit 'of time i notice that the water level goes down more than usual. Lately, the level drops from max to min in a month or so and, in addition, i smell of mold inside the car.
In the past I had the same problem on another car, and it was the tap on the radiator, which leaked. In the case of Rio/Accent, the radiator is a single body, so i suspect that will be drilled. Is it possible to remove it without completely dismantle the dashboard, as happens in many modern cars?
In the past i seem to have touched the internal radiator hoses, on the passenger side, but does not know if there's enough space to pull it off.
View 18 Replies
There were some minor coolant leakage from the upper hose radiator so I have it replaced. Took me 2 hours because the thermostat housing hose neck gunk up with white lime.
Everything works fine but the car still suffering from minor coolant lost. Found some water stain over the bypass hose neck so I get it replaced too. Took me another 2 hours to get it fix because of the white gunk buildup. Secured everything including the hose and the clamps. Minor water stain still can be found at the bypass hose neck.
Replacing the radiator hose? Does it takes few days for the new radiator hose to fit 100%?
View 6 Replies
My 06 accent GLS has become difficult to start only after refueling, which I'm guessing is related to a bad purge control valve from what I've read. Where exactly is the valve located, and is this something that someone with relatively little automotive repair experience could do on their own? I think I've located it on the backside of the engine near the air intake.
View 2 Replies
I recently bought new Accent 2011 and drove it for a couple of weeks. Couple of days ago I noticed that only one out 3 Power Window Buttons lights up with when dim lights are on. Also there are no lights for power lock bottom. Is it the way it suppose to be or it is some sort of an issue? The only reason I noticed it, is that my driver side power window button lights up and the rest don't.
View 5 Replies
I had to replace my brake sensor on side of pedal, and now my car won't recognize the brake is depressed to release safety on sifter to allow me to shift out of park.
View 7 Replies
The timing belt broke in my gf's '08 accent recently and I decided to have a crack at replacing the belt after getting a quote for $900 from the nearest mechanic (with no guarantee it would fix the problem).
When re-aligning the cam and crank to TDC, I wasn't sure if it mattered which revolution the crank was on (ie. 1st or 2nd revolution) when putting everything back together. I tested rotating the engine with the new belt on slowly to make sure there was no contact and everything seemed ok.
So basically now everything is back together, tried starting it up and it won't start and now i'm wondering if it would make a difference or not if the crank was rotated 1 additional revolution. Otherwise there is more significant damage.
View 17 Replies
I have recently had a problem with my 2004 Prius - the brake lights came on while I was driving (both the red exclamation mark and the orange exclamation mark to the left of the speedometer) ...
The Toyota service center told me that I need to replace the skid Control ecu - the part number that they quoted is 89540 47050.
View 1 Replies
I was trying to find a guide on how to change out my reverse lights to LED, I'm having problems removing the panel. The guide i found on here had all the pictures removed. I'm also trying to change the lights for the make up mirror.
View 14 Replies
I have a 2007 sonata, 4cyl, and just installed new KYB340022 gas,,, front struts. No other work was performed, just new strut installation. ABS and ESC warnings lights are now on since installation.
View 2 Replies
I have a 2008 Gs 350, and I want to change the front of my lights. I was thinking maybe like for the fog lights HID yellow and make the day lights match the head lights. Or make everything match?
View 14 Replies
Had my rear right hub replaced by a mechanic yesterday Faulty bearing ,and upon leaving his shop ,, my dash lit up like crazy , ABS ,Yellow and Red circle , AFS Flashing ,check 4WD ,Check VSC , Brought it right back ,he took it apart to verify the ABS sensor witch seemed ok visually ,and told me it was the hub that could be faulty.
Can a ABS sensor be damaged ,with the use of an impact driver nearby ? Can this ABS sensor be checked with a simple ohm meter ?
View 1 Replies
