I own a out of warranty 2008 Accent manual, now on 94 000km/58 408 miles. This morning, it started to not engage 2nd gear, then when I press the pedal hard it does, then sometimes 4th gear. What could be at fault here, and how do I fix it?
View 9 Replies2001 Accent 1.5 GL 165K miles.
The clutch doesn't engage until it's on the floor. I have to push real hard to allow the gear to engage. It then shifts... sometimes smoothly, sometimes it takes a hard push of the gear shifter, or it grinds until getting into gear.
I've changed the master cylinder twice in about 3 years but those times the pedal had no spring and just fell to the floor and stayed. Now, the pedal has spring (I push it to the floor and it springs back) so I assume the MC is ok. I even bled it with fresh fluid.
I'm not sure if the tranny fluid has ever been changed. Would changing the fluid fix this problem or does it sound like I need a new clutch? I'm guessing it needs a new clutch (or corresponding parts) since I've had two MC's go bad in a few years.
The pedal, even when it's shifting smoothly is pretty non-responsive and still engages a little mushy (comparing it to my 2012 Elantra 6sp).
I have brand new ( 800KM ) Accent with Automatic transmission and I noticed that it shifts from 1st gear into 2nd kinda rough. By this I mean that I can feel shift pretty good, and I don't feel shifts from 2 to 3 to 4. I don't rev engine high, typically shifts occur when engine revs around 2000 rpm.
I am not sure if it is a transmission defect or this is the way it shifts? May be I need to breaking my car first and it will go away?
I have a 2010 accent blue model with stick shift. been fine for 50k miles. Lately i have noticed an issue where i am in first gear and then when i push clutch in to go into second, the lever won't budge. it does eventually go in but it just isn't like it used to be. it happens say about 25% of the time. Since at higher rpms it won't do it but normal rpms it will.
Also, i just had a new short block installed, perhaps something is binding? If I sit in the car, stopped, i can shift into and out of all the gears perfectly. Maybe my 1st gear synchros are going?
My 2008 seems to be having some intermittent trouble shifting into the proper gear at a couple of speed ranges.
Occasionally I'll start it up and pull out of a parking space (or leave a stoplight) and it feels like it's stuck in 1st well after it should have switched to a higher gear (I sometimes feel the upshift at about 10* mph). If I continue accelerating and hit about 40-50 mph, once again it appears to stay in the current gear instead of shifting.
When this issue is happening, the car feels even more underpowered than usual and takes way more throttle than it should to accelerate. This results in a cruising RPM of 3.3-3.5k at 60 mph. At that speed the engine would normally be doing about 2.2k RPM. Similar power and RPM conditions exist in the lower-speed range, too.
This whole thing is usually preceded by a rough shift into gear (D or R) when I first start the car. It's always had a slight lurch in the appropriate direction as I take it out of park, but this is really noticeable.
If I stop the car and come back in an hour, it (usually) appears to have reset itself. I can drive around and the transmission control is as good as always.
This has been going on for about a month, with an episode maybe every week or two. I took it to a shop and they didn't find any problems (I told them about the weird shifting and lack of power).
Does it sound like this is what's happening (it's not getting into the right gear)? Thoughts on what I should do? I can't really remember the speeds.
My clutch peddle made a slight "snap" sound last night and now it is very difficult to get the car to engage in a gear while sitting still, while moving it does ok, but not nearly as smooth as it should be. The other odd occurrence is that while the motor is running and the car is not moving, you can't shift any gears at all, but as soon as you cut the motor, all 5 gears and reverse are easily accessible. Why the sound at the peddle and the trouble in the gear shift mechanism? I am only an advanced beginner with car repair, but I think think this is really bad... 2007 Honda Accord Manual Transmission
View 8 RepliesSo I just installed my short shifter and everything works great, all the gears engage, however, when I put my shift knob on I noticed I couldn't engage reverse because it sits down too low and doesn't allow the reverse lockout to get over the rail and engage reverse. I have to loosen the knob so it sits higher and then I can engage reverse, but it moves around, so I can't leave it like this...right now my plan is to make some sort of spacer for the knob to sit on and then put loctite on it...seems like it would solve my problem. I have a Hyundai Aluminum shift knob and the short shift is OEM so I don't see what could be wrong ...
View 8 Replies2008 Accent - driving down highway, heard a pop and car acted like it was in neutral. I have clutch pressure, you can see the hydraulic assist moving the fork, but gears just wont engage. I can free shift through all the gears with the clutch pushed in or not. Manual transmission and clutch kit replaced about 6 months ago when shifting fork broke inside last transmission and tore it all apart. With car in first (and turned off), I can push the car so I know gears are not engaging.
View 6 RepliesI recently bought a 2002 Accent with the 1.6 auto 133000 miles. I have been reading the postS around here about the crappy transmission. My car seems to have some life in the tranny still but it has slipped from 3rd to 4th gear around 45 mph when i get on the gas too hard. Its also a little sluggish to start off. My question is should i change the fluid out knowing i have a slipping issue? The reason i ask is that last time i changed the fluid and filter on a Jeep that was slipping i ended up having to rebuid it. Is that a real possibility if i change the fluid in this Hyundai?
View 3 RepliesI own an automatic transmission 2004 Hyundai Accent with about 180,000 miles. I bought it brand new, but it seems to be having trouble shifting into the right gear. Many transmission "specialists" keep telling me they can't figure out what is wrong, aside from offering to completely rebuild my transmission. The car has the following symptoms:
1. At a stop sign or red light, my car doesn't always begin idling properly. Sometimes it just won't go anywhere at all, even with the motor running.
2. As I drive down the highway, it acts like it jumps into a higher gear for no reason. It sometimes resets itself with no action on my part.
3. The car jerks back and forth, not seemingly due to shifting into gear, but randomly.
4. The check engine light does not come on often, but by the time I can use a DTC reader, the light goes off.
Everything seems to be intermittent, so I can't replicate the problem on-demand for anyone who wants to inspect the problems. Is there anything I can do? Is there an easy way to figure out what's really going on? I'm assuming this is transmission-related...
I've got a 07 accent with 90k miles on it. It has recently started slipping some (revs high, while in gear, without accelerating, especially in 5th gear). It also can be physically hard to move the shifter into gear sometimes (with my hand).
So, does this mean I need a new clutch? Or are there other possibilities? Should I replace/fix anything with the clutch? Sounds like the flywheel should be resurfaced? Will it shift more smoothly after the fix?
Is this something a newb could do himself? I can change the oil, rotate tires. Outside of that I haven't done much. My toolset for now is fairly limited: two jackstands, a trolley jack, torque-wrench and ratchet sets.
Replaced original clutch on Subaru Forester at approx. 130,000 miles because of slipping. Drove car for a few days and clutch would judder once warmed-up when trying to engage 1st gear. Took car back to repair shop, they said pressure plate was defective/set too stiff and replaced that. Whole car now shudders when trying to engage in 1st gear once the car has warmed-up and particularly on (even a slight) hill. What's not working correctly? Seen some discussion on throw-out bearings, master/slave cylinders and oil on clutch. Unsure.
View 5 RepliesThe Accent has been working great recently until the other day when I got in to go to work and now it suddenly shifts very hard into 2nd. And sometimes 3rd.
This problem seems to come and go. Sometimes it will shift smoothly. Other times it will have to reach super high rpm and I will have to let off the gas and slowly accelerate to get it to shift. This seems to happen throughout all the gears and it does not make any difference if overdrive is turned on or off. Also reverse works just fine.
I checked the fluid and it is at the proper level. It does seem to be a little dirty (not burnt) so I am planning on changing the transmission fluid, but something tells me that is not going to solve this issue. It seems like an electrical issue to me. What it could be?
There are no codes at all on the car. Don't know if it matters but the car just turned over to 100k miles. I've been reading on here about all the problems the automatic trannys have in this car but 100k seems a bit early to have any serious transmission problems.
My car has a bit of trouble starting every now and again. I have noticed it is when I have low fuel. When I try to start it it will just keep winding over. I'll switch my car off completely and try again. It usually starts the second or third time. What could be the problem? Its a 05/06 Hyundai Accent
View 4 RepliesMy wife's 2007 Accent started having starting problems right after filling the tank. Is this an EVAP canister problem?
View 8 Replies09' Auto accent developed an issue that I haven't been able to sort out. Car began experiencing a condition where it was harder and harder to start, over about a 2 day period. As well, when stopped at a light it would idle fine, but almost stall when you tried to accelerate. Once above about 2k rpms it was fine, but then near 4k rpm it felt dead, didn't want to pull.
Only code was P0171.
Here is what I have checked thus far.
All injectors ohm out exactly at 15.1
-Fuel pump primes at key on like it should
-Verified cam/crank are timed properly (timing belt didn't slip a tooth)
-Car is MAP based, so no MAF to deal with. It's totally stock down to the paper air filter.
-Purge solenoid is closed and appears to be functioning properly.
I was checking things last night and this time it didn't want to start at all. I haven't checked for injector pulse or spark (it's coil on plug), but this didn't seem like part of the issue it was experiencing. Almost feels like a cam or crank sensor going out (timing is acting weird). Is there a relatively easy way to test the cam or crank sensors other than just trying new ones?
I have a 2009 Accent. Last year I started to have a hard start issue, very intermittent. It eventually got worse this year.
During the cold, it was never an issue, but during the summer damp or rainy days it occurred quite frequently.
It would turn over, but never start. If I pressed the gas peddle while starting it up, it usually would start the 2nd or 3rd time.
I changed the usual start up components; plugs, ignition coils, cam shaft position sensor, crankshaft sensor, and cleaned the throttle body.
None of those changes worked for the startup. When I removed my throttle body to fully clean it again, I noticed there was an extra air channel into the engine from the TB. Following this, I found the ISCA.
Removing, taking apart, and cleaning the idle speed control actuator seemed to have fixed the issue. It was so caked up with carbon deposit/build up, it couldn't fully rotate.
I used the throttle body cleaner to clean it out and then it began to spin freely (I removed it from the black sensor part first).
Since putting it back altogether, I haven't had a start up issue since.
Here are the notes from the service manual .....
After the -20 winter my 2009 Accent started burning oil at startup and after hard right turns. It was burning about 1 quart of oil per 500 miles. No codes ever appeared. I assumed that it was a pretty classic case of broken valve stem seals. Upon taking the valve cover off I found that there are two oil galleys leading back to the oil pan. One on the passenger side of the engine was exposed and had a large carbon deposit on the valve cover just above it indicating all the crankcase vapors were coming through that gallery and condensing. The galley was partially plugged. The other galley on the left side below the camshaft was completely plugged. Some cleaning first with a loop of welding wire and cleaning out the PCV chamber which was filled with oil has cleared up the problem. I followed with an oil change and then another change at 500 miles. I've used no oil in 1200 miles since the last change.
View 5 Replies2007 Accent GLS, US-market, Automatic, 140k miles
This is my wife's car. She called me from the side of the road while I was on a job out of town. The car had stalled while driving. She was able to re-start the car with check-engine lamp showing and took the car directly to a garage. It ran normally during that trip.
The garage diagnosed the problem as a failed crankshaft position sensor. They cleared all codes from the ECU without telling us what they were. My wife told them I would fix it when I got home. She drove the car home, parked it there and used my car until I got back.
When I got home, I replaced the crank position sensor with a new beck-arnley part. It was a poor fit, but it did go in. Now roughly every other start takes a few extra cranks. It always starts. It does not stall once started. No check-engine light since the initial episode. I just don't like the random hard starts.
Normal fuel consumption & power output. All other maintenance is up to date.
Gremlin that causes the car to take a few tries to start when it is cold or damp? I've read that the crank sensor and fuel pump/fuel injection relays are possible culprits, but since the crank sensor is almost $100 I'm hesitant to throw money at an intermittent problem without a 100% diagnosis
-No codes in computer
-Brand new battery
-Mint NGK Platinum spark plugs
-Runs like a top once it starts
-5W20 synthetic oil
Usually it starts first flick of the key. Sometimes first flick fails no matter how long i hold it, then second flick it starts fine. If its really cold it sometimes takes up to 5 attempts. It cranks but doesn't "catch". The actual cranking itself is very strong with no hesitation which tells me it isn't starter, battery or thick oil.
My 07 has difficulty starting, only after adding fuel, or a fill up. I thought at first it was due to over filling, but it occurs after adding any amount of fuel. If I leave the car running while attempting to fill up, it sputters and dies. I have to press the gas pedal to the floor to start it, and it sputters for a few minutes, then runs fine, and starts fine until fuel is added once again. I searched and found where the General mentions a Vapor hose, but could not find more.
View 2 Replies