Accent MC (2006-11) :: 2010 - Timing Belt Went Out At Idle While Making A Turn
Sep 6, 2014
The timing belt went out at idle while making a turn. I changed the timing belt, but when cranked you have to pump the gas to keep it running and it is really rough running with a smell of gas when you turn it off. On the last run it backfired slightly. There is no knocking or pinging. And have triple checked the timing. Could improper torque on the crankshaft bolt cause this or failed ignition coils?
View 21 Replies
Advertisement
Rebuilt a motor due to the timing belt failing. Everything works except I can't get the timing to line up perfectly.
From what I'm getting from the service manual, line the camshaft sprocket with the mark visible from the hole
Line up the crankshaft gear with the yellow mark at the bottom.
Do I have to do a double/triple turn of the cam/cranks to get TDC to be achieved properly? My biggest problem on this car is having the crank gear shift a couple teeth after tensioning the belt.
View 4 Replies
2004 Accent 1.6L
Changed the timing belt and water pump this past weekend. I made sure the timing marks aligned before I put the belts on. They were still aligned after turning the engine by hand and still aligned after taking the car out for a test drive. I did not notice rough idle when I started the engine in the garage nor did I notice a rough idle during the test drive.
A few days later I am now noticing the car will idle roughly when I come to a stop. The idle will get rough enough to gently shake the car. No engine light and no unusual noise from the engine.
I am going to check the timing marks again tonight. I suspect the belt may actually be off by one tooth. I have driven over 100 miles since changing the belt so I don't believe it is off anymore than one tooth or else I presume I'd probably have already broken down or been hearing unusual noises.
Furthermore, I do not seem to have any loss in power. I still have good acceleration and no roughness unless at idle engine speed. I do, however, run rough at higher speeds (75+ mph) on the highway, but this was present before the timing belt change. Unfortunately the car does not have an RPM gauge.
Having said all of this, are there any other possible reasons why I might be idling rough now?
View 4 Replies
The timing belt broke in my gf's '08 accent recently and I decided to have a crack at replacing the belt after getting a quote for $900 from the nearest mechanic (with no guarantee it would fix the problem).
When re-aligning the cam and crank to TDC, I wasn't sure if it mattered which revolution the crank was on (ie. 1st or 2nd revolution) when putting everything back together. I tested rotating the engine with the new belt on slowly to make sure there was no contact and everything seemed ok.
So basically now everything is back together, tried starting it up and it won't start and now i'm wondering if it would make a difference or not if the crank was rotated 1 additional revolution. Otherwise there is more significant damage.
View 17 Replies
In the process of rebuilding a 2007 Accent where the timing belt broke while idling.
Pulled the head, ran a "water test" on the valves (put spark plug in, pour water on the valves and see if it comes out the exhaust/intake side) and found that only 2 intake valves were belt. Also shut off all the lights in a pitch black room, shined a flashlight in the intake/exhaust and didn't see any light leak from any of the cylinders except the one with the 2 bent valves.
Does this make sense? I would assume since 2 cylinders are always TDC at once, at least 4 valves would be bent.
Lastly, before rebuild I'll be replacing the 2 intake valves, all the valve stem seals, intake manifold gasket, exhaust manifold gasket, head gasket, head bolts and valve cover gasket. Anything else I should replace on the head? Trying to keep costs down as much as possible.
To add: Pistons have no damage on them, there are no marks of the valves hitting the pistons. The timing belt was replaced after it broke and the engine still ran however it ran rough. Compression test was done on only cylinder 1&2, 1 had 60 PSI and 2 had 0 PSI. Compression test was also done by just rotating the crank with a socket since I already had some of the engine disassembled.
View 4 Replies
I have a 2007 Accent with 119K on it.
I wanted to replace the water pump and I was wondering if this can be replaced without removing the timing belt or the lower timing belt cover?
View 8 Replies
My car has 103000 miles on it and the timing belt was replaced several hundred miles ago. After the service I noticed it had a bit of a rough idle and a very slight sputtering noise, but still no check engine light. Was the timing belt put on wrong? The engine is non-interference, by the way.
View 1 Replies
I was thinking about checking out the above vehicle at my local dealer (Chevrolet). They're asking 15.9k and it has 57k miles. I need to know if it has a timing belt or a timing chain and how reliable is the engine/transmission.
View 1 Replies
Serpentine belt on a 2006 Honda Odyssey fraying and then ripping into the timing belt causing that belt to break? I recently had this scenario given to me as the cause of my recently replaced timing belt breaking.
View 11 Replies
I just changed the timing belt and everything runs great. I pushed the AC button and no light came on. I checked all the fuses and they are good I took the H and L caps of and tapped the pin and there was air blasting out. Don't know what it could be? All I did was loosen the compressor and remove the belt and put it back on.
View 2 Replies
I just finished replacing my timing belt, water pump and all belts. I made sure to double check the timing marks lined up via this pic:
Timing belt diagram
I put everything back together and no go. I am not sure what to do now. Should the crank sprocket pulley be in a special starting position? I see is has a "1" engraved on it.
View 22 Replies
So 2 months after my accident I'm finally able to drive again and my car is 100% fixed and ready. Only 1 problem, every time I make a left turn my car makes this weird noise but I don't know what it is. I replaced my suspension and I thought it would take a couple days for the tightness to wear down and for the noise to go away, but of course with my luck it's still doing it. What can it be??
View 5 Replies
I have a 2006 Honda Odyssey. I got the timing belt replaced two weeks ago.Last week the engine started making a quiet clicking noise upon acceleration. The clicking noise happens intermittently not continuously. Then last night the yellow engine light came on. Questions: What does the yellow engine light mean? Is the engine light related to the timing belt work that was done? Would the clicking noise be connected to the timing belt work?
View 3 Replies
My mechanic just did the timing bet, water pump and other belts. Also changed the tensioner.
Car runs fine and everything seems great until I get to a red light. The engine sounds louder then before. Not very loud but its louder and maybe a very slight vibration, not sure yet. No noises while driving, seems like its running the same or better then before. Runs fine though
View 4 Replies
Is there a "how to" on adjusting the tension of the timing belt in a 2002 accent 1.5L ....
View 1 Replies
Vehicle is an 08 Hyundai Accent 1.6L three door (hatchback) with 20,197 miles. This car was born on Oct. 16, 2007 and purchased in April of 2008. I told the owner to call the dealer and find out about when they should replace the timing belt as I had looked it up at the Gates site and found that it is an interference motor and also these Hyundai have some kind of lengthy warranty. When the tech or whoever she spoke to at the dealership asked about the mileage, they told her that she does not need to worry about the belt for about another five years, were rude and sounded inconvenienced by her calling. This leaves her with a bad taste in her mouth and more importantly, mis-informed.
I get the "Maintenance Log" out of the glove box and upon trying to decipher the timing belt interval, it states that the first course of action is an "inspection" at 30,000 miles or 24 months. How is a timing belt inspected? From what I have seen, a belt can look perfect today and snap tomorrow. But anyway, the next entry for severe service is replacement at 37,500 miles or 30 months which means this belt should have been replaced in October of 2010. Next entry is normal change at 60,000 miles or 48 months which puts us at April of 2012. After this it goes to 75,000 miles or 60 months.
I have already picked up the kit for changing the belt, tensioner, idler, and the two seals. How critical is it to change the spring as that was not included in the kit I got? I'm planning to do this job here in the next couple days as from what I can figure from the above log, It's way over due. I was reading some Hyundai forums and one stated that the 2011 model with the exact same engine calls for the first replacement due at 90,000 miles. How's this possible? Seems like these people (engineers) don't have all their stuff in one bag...
View 7 Replies
We have a 2010 Hyundai Accent, with low miles (10,000), and the A/C Compressor is making a "growling" noise. The only way to explain the noise is when you hear a human try to immiate the sound of a dog growling. That's exactly what it sounds like.
First thing in the morning it doesn't make the noise to much, but as you drive for a bit you will start to hear it. Sometimes it's really loud, sometimes quieter. When you shut the A/C off, it will continue for a few seconds then stop.
The service department told me it was the compressor and it is, "pretty normal on the cars." How is that normal though? It sounds awful.
View 9 Replies
I bought a 02 accent base model hb 5 speed 109k miles for a winter car (have a mustang in garage.) It ran good until tonight when the timing belt snapped. I know this because while driving it made some ticking noises and then shut off and when you try to start it the noise that comes indicates no compression so the belt must've snapped and bent the valves.
View 3 Replies
I have 130K miles on my Santa Fe. I just replaced the timing belt without the water pump being replaced. Picked it up from the mechanic and the check engine light was on and it was idling very rough. Left it there for him to recheck. He said maybe he didn't plug in the Cam Sensor all the way or at all. Next day he called me and said that the cam sensor was bad and he replaced it for free. Picked up the vehicle and the idle was a little rough but got worse on the ride home.
View 1 Replies
My wife and I recently bought a 2005 Subaru Outback 2.5 XT with an automatic transmission. Last week, we had the timing belt changed by a mechanic I've gone to for the past four years and trust a great deal. He changed the timing belt, drive belts, water pump, pulleys, tensioner and a few hoses, and everything seemed to go off without a hitch. After picking up the car, though, we noticed that the idle seemed much rougher than it had in the past. We can't tell if it's also rough during driving, or when the car is in park or neutral, but there is definitely considerably more vibration when the car is stopped in drive and idling--you can feel it throughout the car. I haven't noticed it until the car has warmed up.
I asked my brother, who is a mechanic in another state, if he had any thoughts, and he said it could be that the belt is off a notch, a vacuum leak or an unplugged sensor. I brought the car back to the mechanic today to see if it he could fix it, and he said that the CEL would be on if it was a vacuum leak or unplugged sensor, and that the car has an automatic idle that the belt change would not have adjusted. He asked if the vibration was getting any better, since when the battery was unplugged it would take the computer awhile to relearn the correct idle, but we've driven it a few hundred miles and it hasn't gotten any better. I left the car with him to take a look at it, but he just called and said he couldn't find anything wrong.
I want to chalk this up to us imagining something, but we both have no doubt that there has been considerably more vibration at least when the car is idling since we picked it up after the timing belt change. Is there anything else that it could be or that I should ask my mechanic?
View 10 Replies
One of my belts squeaks. I've tightened one of them as far as it goes I think. The other one is the one with the alternator. Do I tighten the pulley bolt on the alternator to add tension to that one?
View 4 Replies
