Accent MC (2006-11) :: 2010 SE Grinds When Shift Into Reverse
May 2, 2011
I've had my new left over 2010 SE for couple weeks now. done 600 miles.
I noticed at first a couple times when shifting from 1st to reverse while parallel parking and still slightly rolling forward, the the gear grinded a bit, despite the clutch being fully depressed. I figured maybe with this manual tranny compared to others i've driven that you just have to be dead still before shifting into reverse.
But then yesterday morning from my driveway, from a standstill I shifted into reverse and it grinded too, again with the clutch fully depressed. Is this normal with these cars? I've driven manual gtis and a ford focus and never experienced this before? Is this a problem?
the fact that it's happened three times now within a couple weeks tells me it's not me being sloppy on the clutch, it is definitely grinding with my foot all the way down on the clutch.
View 16 Replies
Advertisement
So I just installed my short shifter and everything works great, all the gears engage, however, when I put my shift knob on I noticed I couldn't engage reverse because it sits down too low and doesn't allow the reverse lockout to get over the rail and engage reverse. I have to loosen the knob so it sits higher and then I can engage reverse, but it moves around, so I can't leave it like this...right now my plan is to make some sort of spacer for the knob to sit on and then put loctite on it...seems like it would solve my problem. I have a Hyundai Aluminum shift knob and the short shift is OEM so I don't see what could be wrong ...
View 8 Replies
So there is an imowa 20th that im really interested in, 100k chip and exhaust. But there is a problem that could be a deal breaker
He says that 6th grinds when you go into it, it has no problem getting in but it makes a noise when you shift in, best guess is that its a synchro problem. This would not bother me so much if this wasn't an 8 year old limited edition sporty hatchback with a transmission unique to the standard gti.
View 4 Replies
I have a 5 speed 99 Jeep Wrangler and when the car is running, it's extremely hard to put the car into first gear from a standstill. However, once it's in gear, shifting is fairly normal but still offers a little resistance. I feel like I have to wiggle it into gear. When putting the car in reverse from a standstill, the gears grind terribly.
Once the car is off, shifting is still difficult until I put it in reverse. Somehow, this "fixes" the problem and everything shifts smooth as a dream until I start the engine and then it's a 50/50 shot until it eventually fails later on.
View 4 Replies
I own a 1996 XL Ford Ranger 2wd 5 speed manual.
Last week I had it in for some service, which included bleeding the clutch lines and new fluid.
Since then when putting it in reverse the transmission grids. It is also very difficult to get into first gear - I really have to shove hard on the stick.
Better Description of symptoms: When the vehicle is moving it shifts fine. When I come to a stop, put it in neutral and let out on the clutch, it is then very difficult to get back into first gear. If I leave the clutch in, fter I come to a stop, I can shift around to all the gears no problem. It's only when I let out on the clutch, then push it back in to shift into first is the difficult part.
With reverse, I have to move ahead a bit, THEN I can shift to reverse without the grinding noise. I talked to my mechanic who check to ensure the fluid was NOT low (it wasn't) and no air bubble existed in the line. After that was checked, he said the clutch is worn and has to be replaced.
Well, then, why wasn't it doing this BEFORE I had him bleed the lines? It started the day I picked the truck up from service. He recommends the following to fix the problem...
- slave cylinder
- new line
- disc
- preasure
I am asking why this would happen after he bleed the lines? Is there another problem that can cause this?
View 14 Replies
Vehicle was repaired after front end collision and I get no codes found on scanner, had some bad connectors which I replaced and codes went away. I don't get ready light and the dash lights do not cycle off (ABS, SRS, Check engine, Etc. Etc.) The car will shift into neutral but not drive or reverse. Has new Aux battery and Hybrid battery is showing two bars. What to check ?
View 6 Replies
When I shift to reverse, the side mirrors angle downwards automatically. The driver's side one squeaks when it does this. Any tip to remove the squeak.
I recently upgraded my puddle lamps to blue LEDs to match my interior lights and took the opportunity to spray a little bit of WD40 on the mechanism. I didn't use much, since the mirrors are basically friction fit I didn't think it wise to spray all over, but that didn't seem to make any difference.
The mirror still seems to move freely enough and nothing obvious is rubbing.
View 3 Replies
I have a 2010 RX and I've recently noticed every time I shift from Drive to Reverse and vice versa there's a squeaking noise coming from the shift stick. What this could be and if there's an easy solution?
I'm not due for service or an oil change for another 5,000 miles so I'm hoping it's not something I need to address immediately. Do you think it would be safe to wait until then?
View 1 Replies
I bought a 2010 V8 Explorer on Monday and aside from the apparent "known issue" with the hard 2-1 shift (which I'm trying to get it to "unlearn" by driving differently), it's a really nice truck.
When I shift into reverse it says "Park Aid On/Off" in the display, and sure enough, it beeps when I get close to something. That said, there aren't the normal "dots" in the bumper that I normally associate with backup sensors.
Everything works just fine with it, I just am a guy who likes to know how things work and I don't see anything on the outside that would indicate it's a parking sensor.
View 7 Replies
So my automatic accent with 82000 KM is doing some funny things. The first, is occasionally when shifting from 1st to 2nd gear, it will shift, and then almost shift again with a bit of a jolt (double shift?). The second, is when in 4th gear, when at 2000 rpm, it will jerk, almost like if it shifts yet there is nothing to shift too (4th is the highest gear). What is going on here?
View 3 Replies
Like the title says. All of a sudden when I put the car in reverse I got a rumble and the car vibrates some.
View 41 Replies
[URL] .... You have to crank your speakers to hear properly, the mic in my phone was trying to cancel the engine noise I think... Someone suggested an exhaust hanger in another thread, I still have to get under the car next oil change and check that.
View 1 Replies
Two big issues of concern with my newly purchased used Accent with 40k on it.
When starting the car first thing in the morning, when I drive the car out my drive way in reverse, it feels like it runs a little rough in reverse. Nothing dramatic, but still strangely rough to cause me a little concern. The rest of the day i only have to reverse briefly from parking spaces, so i dont really notice it then. Is this normal? My driveway is also at a slight downhill angle, which may be related to the roughness?
My second big concern, is my AC makes a very low, hardly audible, but still noticeable growling sound. It is most noticeable after the car has been sitting a few hours, then I start it, and if I wait for about 30 seconds, I hear it growl for about 10 seconds. While driving the car around I hear it sporadically make the sound then too. It isn't consistent enough to say I hear it every certain amount of time. Its very random, except I always hear it after it's been sitting for a long time.
I can hear the sound best when the fan is set to Level 1. Turning it up to Level 4 doesn't make the growl louder, but it makes the fan so loud that its harder to hear the growl. Also, when I have it at level 1, and turn the AC button off, the growl goes away. It's concerning to me, and when I took it to the dealership, it wouldn't make the growl sound when the guy listened.
View 8 Replies
I was once the proud owner of a 2006 Prius with 106,716 miles on it. Never missed a regularly scheduled service. Now, I am no longer proud, but just another owner of a Prius with a failed transaxle.
Last week, I parked my car on my way to work and, while the car was idling in park, the Triangle of Death (red with exlamation mark within) came up on the dashboard. The car went into limp mode -- it was unable to shift into drive or reverse -- so I had it towed to Darcars in Silver Spring, MD. They thought the original 12v battery was dead, so they replaced it.
P0AA6 -- 526 and 613 codes 600 miles after Transaxle Fluid Replacement...
View 10 Replies
Should we go to a transmission specialist or a regular shop for our issue? 2006 Kia Sedona - won't shift into reverse suddenly and is in "limp" mode, only staying in 3rd gear.
My concerns are primarily getting it done correctly and as cheaply as possible. I've read that the issue could be an input or output solenoid or maybe having to get a full on re manufactured transmission instead. But the consensus appears to be having it properly diagnosed.
So my question is, will the local shop around the corner who is pretty good with most repairs be able to properly deal with this? Or am I better off skipping them and going to the specialist?
View 6 Replies
I noticed this week the gear shift light was out on my 2008 Accent GLS. I tapped the side of it and it came back. Next day, same behavior.
View 11 Replies
So, back when my car was my dad's, he used to drive a lot on the freeway for his job. He said that after getting off the freeway and transitioning to in-city driving, the transmission would start to act up. It only happened when the car was hot, and it's generally fine for just driving a couple miles to work like I do, albeit the occasional rough shift every now and again, but I'd like to be able to hit the freeway if I need to without worrying about the transmission badly misbehaving.
Also, I'm not sure if it's even relevant to that issue, but I've been aware of the fact that at least two of my ignition coils are bad, a common problem in MC Accents to my knowledge, and the engine hasn't been running as smoothly as it could be for the past several months. Is it at all possible that a long-standing misfire issue could play havoc with shifting patterns when the transmission changes from freeway to in-city shifting behavior?
View 2 Replies
I have brand new ( 800KM ) Accent with Automatic transmission and I noticed that it shifts from 1st gear into 2nd kinda rough. By this I mean that I can feel shift pretty good, and I don't feel shifts from 2 to 3 to 4. I don't rev engine high, typically shifts occur when engine revs around 2000 rpm.
I am not sure if it is a transmission defect or this is the way it shifts? May be I need to breaking my car first and it will go away?
View 16 Replies
Everything was working fine until I started messing with camera settings in the service menu today . Now when I shift into reverse, it says "system not ready". Will not let me parallel park or reverse park now. I tried to reset the settings but maybe I don't know how to "save" settings.
View 5 Replies
2007 GS350 ... Mirror only moves down sometimes when I shift into reverse. Malfunction started about month ago.
View 14 Replies
My Accent is a 2007. It regularly has the check engine light come on. They continually claim it's the fuel cap. When it's colder, even when it's been running it continually stalls when your putting it in reverse. They also claim that's not a problem. It's only got 25K on it. So the fact that it's already have problems is rather annoying.
View 5 Replies
