Accent MC (2006-11) :: 2008 - Won't Start Up After Replacement Of Timing Belt
Aug 24, 2014
The timing belt broke in my gf's '08 accent recently and I decided to have a crack at replacing the belt after getting a quote for $900 from the nearest mechanic (with no guarantee it would fix the problem).
When re-aligning the cam and crank to TDC, I wasn't sure if it mattered which revolution the crank was on (ie. 1st or 2nd revolution) when putting everything back together. I tested rotating the engine with the new belt on slowly to make sure there was no contact and everything seemed ok.
So basically now everything is back together, tried starting it up and it won't start and now i'm wondering if it would make a difference or not if the crank was rotated 1 additional revolution. Otherwise there is more significant damage.
View 17 Replies
Advertisement
Vehicle is an 08 Hyundai Accent 1.6L three door (hatchback) with 20,197 miles. This car was born on Oct. 16, 2007 and purchased in April of 2008. I told the owner to call the dealer and find out about when they should replace the timing belt as I had looked it up at the Gates site and found that it is an interference motor and also these Hyundai have some kind of lengthy warranty. When the tech or whoever she spoke to at the dealership asked about the mileage, they told her that she does not need to worry about the belt for about another five years, were rude and sounded inconvenienced by her calling. This leaves her with a bad taste in her mouth and more importantly, mis-informed.
I get the "Maintenance Log" out of the glove box and upon trying to decipher the timing belt interval, it states that the first course of action is an "inspection" at 30,000 miles or 24 months. How is a timing belt inspected? From what I have seen, a belt can look perfect today and snap tomorrow. But anyway, the next entry for severe service is replacement at 37,500 miles or 30 months which means this belt should have been replaced in October of 2010. Next entry is normal change at 60,000 miles or 48 months which puts us at April of 2012. After this it goes to 75,000 miles or 60 months.
I have already picked up the kit for changing the belt, tensioner, idler, and the two seals. How critical is it to change the spring as that was not included in the kit I got? I'm planning to do this job here in the next couple days as from what I can figure from the above log, It's way over due. I was reading some Hyundai forums and one stated that the 2011 model with the exact same engine calls for the first replacement due at 90,000 miles. How's this possible? Seems like these people (engineers) don't have all their stuff in one bag...
View 7 Replies
I just finished replacing my timing belt, water pump and all belts. I made sure to double check the timing marks lined up via this pic:
Timing belt diagram
I put everything back together and no go. I am not sure what to do now. Should the crank sprocket pulley be in a special starting position? I see is has a "1" engraved on it.
View 22 Replies
How to change the timing belt and water pump on a 2006 2.0t passat?
View 3 Replies
I recently replaced a timing belt in a 2003 ALH TDI & since it will not start. When I took everything apart I found the belt extremely worn & the engine had actually slightly jumped timing. When I replaced the pulleys & belt & reset the timing to the way it would be from factory. When I tried to start the vehicle it turns over fine but will not catch. I double checked all the timing, fuel pump, everything - all okay. I can get it running with ether but will not start with diesel fuel. I also replaced the fuel filter, checked to make sure there was fuel at the injection pump but nothing works.
View 4 Replies
Rebuilt a motor due to the timing belt failing. Everything works except I can't get the timing to line up perfectly.
From what I'm getting from the service manual, line the camshaft sprocket with the mark visible from the hole
Line up the crankshaft gear with the yellow mark at the bottom.
Do I have to do a double/triple turn of the cam/cranks to get TDC to be achieved properly? My biggest problem on this car is having the crank gear shift a couple teeth after tensioning the belt.
View 4 Replies
2.5 Litre ... Okay, I've done this on other cars, both Fords without a problem but now I'm stuck on the no start situation. I have spark and my fuel pressure is 60 psi. About to do a compression test. Only issue with replacing the belt is that no matter how many times I try removing and installing it I'm always 1/2 tooth off after rotating the engine a couple of times but that shouldn't be enough for a complete no start. Tried starting fluid. Replaced cam sensor. new plugs. checked firing order. I have spark at #1 according to my test lamp which plugs inline.
View 6 Replies
In the process of rebuilding a 2007 Accent where the timing belt broke while idling.
Pulled the head, ran a "water test" on the valves (put spark plug in, pour water on the valves and see if it comes out the exhaust/intake side) and found that only 2 intake valves were belt. Also shut off all the lights in a pitch black room, shined a flashlight in the intake/exhaust and didn't see any light leak from any of the cylinders except the one with the 2 bent valves.
Does this make sense? I would assume since 2 cylinders are always TDC at once, at least 4 valves would be bent.
Lastly, before rebuild I'll be replacing the 2 intake valves, all the valve stem seals, intake manifold gasket, exhaust manifold gasket, head gasket, head bolts and valve cover gasket. Anything else I should replace on the head? Trying to keep costs down as much as possible.
To add: Pistons have no damage on them, there are no marks of the valves hitting the pistons. The timing belt was replaced after it broke and the engine still ran however it ran rough. Compression test was done on only cylinder 1&2, 1 had 60 PSI and 2 had 0 PSI. Compression test was also done by just rotating the crank with a socket since I already had some of the engine disassembled.
View 4 Replies
I have a 2007 Accent with 119K on it.
I wanted to replace the water pump and I was wondering if this can be replaced without removing the timing belt or the lower timing belt cover?
View 8 Replies
The timing belt went out at idle while making a turn. I changed the timing belt, but when cranked you have to pump the gas to keep it running and it is really rough running with a smell of gas when you turn it off. On the last run it backfired slightly. There is no knocking or pinging. And have triple checked the timing. Could improper torque on the crankshaft bolt cause this or failed ignition coils?
View 21 Replies
2008 Hyundai Elantra, 2.0 it. We replaced a bad water pump, and timing belt while we were there. I followed directions found on multiple websites. We spun the crank shaft to the top dead center mark on the crank sprocket/engine block, and the cam sprocket / assignment mark. Then removed tensioner, and belt. Installed new belt and ensured alignment marks had not moved. Applied pressure to tensioner and tightened. Reassembled everything else. Car started with no problems, drive for about twenty minutes started making clicking sound from under the hood, we turned around to come back home and the car still making clicking sounds gradually started to loose power and speed until the engine stalled and would not restart. Trying to find out what could have happened.
View 2 Replies
I am looking for a link or instructions on replacing the timing belt on a 2.8 30V. I attempted to search and mostly came up w/ the info relating to the turbo.
View 2 Replies
Serpentine belt on a 2006 Honda Odyssey fraying and then ripping into the timing belt causing that belt to break? I recently had this scenario given to me as the cause of my recently replaced timing belt breaking.
View 11 Replies
My 2004 Passat 1.8T GLS (station wagon) has 72,000 miles. I checked the manual which says that timing belt is to be replaced at 105,000 miles.
However, car is 8 years old - does the age matter or I should be fine until I get to 105,000 miles to replace the timing belt, tensioner, water pump etc.
View 8 Replies
I got 123000 km on my car. Manual says 144000 km is the right mileage to replace the belt, but I have heard opinions that it should be done earlier.
View 7 Replies
Does VW have an official recommendation for replacing the timing belt?
None of the publications I've seen list the timing belt interval. My car is very close to 95k miles.
View 22 Replies
I was told that I must replace the timing belt every sixty thousand miles. Is this true?
View 24 Replies
Looking for the proper instructions in replacing timing belt and oil seal I have done this on a Honda accord before but I need to know how to properly align everything so I can do it right the first time.
View 2 Replies
2007 Santa Fe GLS 2.7 V6. T belt replaced by dealer at 62K. Noticed engine vibration when picked up vehicle. RPM is steady, engine runs smooth, no error codes, no strange noises. Mechanic who did the work confirmed vibration problem and recommended bringing it back - had no answer on the cause but mentioned lose motor mounts which I doubt - the car ran perfect until the dealer did the work.
View 3 Replies
My 2001Honda Civic EX (manual) has only about 46,000 miles on the clock and runs very well. My mechanic says I should consider replacing the timing belt (the manual suggests after seven years). I plan on keeping the car for many more years -- should I replace the belt now? How devastating is it if the belt breaks while driving?
View 5 Replies
I think I made a bad decision. Almost a year ago, I purchased my used Odyssey. I cannot remember if the timing belt had been changed. My check engine light came on, and the mechanic I took it to indicated it was the seal on the gas cap. He proceeded to tell me that I have an oil leak coming from the oil pump and that I should replace it and while I'm in there, I should replace the timing belt. There were a myriad of other things wrong with it, including broken engine mounts (which I can get fixed elsewhere from the man I purchased the car from) and some other things he said I can spread out and are basic maintenance, but I said to go forward with the oil pump and timing belt.
View 6 Replies
