Getting some vibration at high speeds on the highway, and when I changed my wheels, I noted that there seems to be some free play in the ball joint on the end. Is this normal? Can I replace just the end of the tie rod?
View 3 RepliesI have a 2006 accent 1.6l dohc. While doing highway speeds the rpms are very high considering the small engine. There for it give me a result of bad fuel mileage with 480km per 40l tank. I'm curious is there is any 6speed transmission I can swap out my 5 speed with in order to give me that extra gear to bring the rpms down.
View 10 RepliesI just bought a 2011 accent 5 spd ... Quick question, when I drive it at highways speeds. (65mph) I notice that i am running around 3500 revs. Is that normal? It seems a little high to me. Every other 4 banger I had never ran that high in 5th gear at 65 mph.
View 5 RepliesThis has been happening for the past 6 months or so. I recently had new ball joints, 4 wheel alignment, and 4 wheel balance. Even with this I'm noticing a very slight high frequency vibration at highway speeds. I noticed on one of the front wheels that a weight fell off, so this might explain the high speed vibration.
However - When I'm starting at 0mph, and accelerate to say 50mph for example, the car vibrates rather substantially as the speedometer moves from around 25mph to just past 30mph. After those speeds it goes away.
I've also noticed that it tends to be worse if I'm going up hill, which, according to the laws of physics, would tell me that going uphill would put more pressure on the front end, given it's heavier with the engine there. If I'm going downhill it vibrates much less.
When I drive I tend to not accelerate quickly, meaning, I don't 'punch' it, and accelerate gradually instead. If I'm driving on a level, well-paved road, and accelerate quicker than regular, the vibration seems to not be as heavy.
Any other tests for this? Struts, control arm, steering knuckle, drive shaft ?
I recently got a used 2000 silverado 1500 ext. cab with a short bed. Has a 5.3L engine. I noticed it has vibrations at highway speeds. I thought it was the crappy tires on it so I had all the tires replaced and balanced. Now it has all new tires and does the same thing. Runs really smooth all the way up to 40mph and then the vibrations begins. It is mostly felt in the steering/dash and pedals. A little more pronounced on accel. but vibrates if your on the gas on not.
Once your reach 65mph, the vibrations stop. I have also noticed that asphalt makes it vibrates more. When I go over concrete overpasses in the problem area of 40 to 65mph it smooths out. I took a look under the truck and saw nothing obvious. U joints feel tight and no play, seen it had weights which appeared welded onto the one piece drive shaft.
My accent just crossed 180K mark. From last year the steering wheel shakes quite a bit at highway speeds ,say 70MPH. It's especially bad when I accelerates . Took the car to a shop, they told me two things, the CV axle of passenger side needs replacement, and the wheel hub bearings are bad(both front wheels). They quoted me $200 for replacing the cv axle, and $400 for replacing both front wheel bearings. Since I don't even think the car worth $600 right now(given high mileage), I told them I'll just do the axle(I know how to do it myself but don't have the time, plus it won't be that much cheaper DIY anyway). They said fine, but if you don't replace the bearings you may have the wheel fly off one day and that's dangerous.
They replaced the axle, and the car drives a lot better now. There's still a little bit of shaking at high speed but 75% of that shake has gone away. My question is, does the worn out bearing causes car to tremble at high speed? I heard other people told me there should be a grinding or loud hawling sound if the bearings are bad, but I don't hear that. I searched the internet and some people say, to determine if the hub bearings are bad, just drive it for 10 minutes then feel the hub. If it's barely warm, the bearings are good. If it's warm to hot, then the bearings are bad. I felt it and it's warm, but not too hot to touch. I tried the rear wheels and those are barely warm indeed.
So from this method it seems the front wheel hub bearings are indeed bad. I wonder how long I can keep driving this without endanger myself. $400 is not cheap for this car and I don't have a machine to press in the bearings myself. I can disassemble the rotor and hub that's not a big deal, but I don't know how to get the old bearing out and the new bearing in. Is there a machine shop that just do the pressing? Or, is there any shop selling the hub assembly with bearing already in place? this way I just remove the old hub assembly and replace it with the new assembly, a lot easier. I searched the internet but can only find pre-assembled hub w/ bearing for the rear wheel of this car. I need the front ones.
I've got a 2000 Suburban 1500 4WD with the Auto 4WD. I'm running into a vibration at highway speeds along with a clicking sound at idle speed which speeds up and slows down with speed. I've discovered the u-joint on the front drive shaft where it connects with the transfer case is worn and has play in it. Could this cause the vibration?
Also, The front drive train spins any time the vehicle is motion, which is to say the front drive shaft spins as the truck goes down the road, correct?
I drive a 2000 Dodge Dakota Sport w/ 4.7L V8 engine. I have been dealing with an overheating problem for about 6 months now and have nearly exhausted all hope of correcting the issue. It has been in the shop on 4 separate occasions and seen 2 different mechanics. The radiator has been replaced, the thermostat and thermostat housing have been replaced, the radiator fan works properly, hoses have been replaced and no subsequent leak has been found by either mechanic, they haven't mentioned the possibility of a blown Head Gasket (nor has the typical "milky residue," shown up in my oil cap). Each time I got it back from the shop the problem was fixed for about two weeks, then returned and slowly got worse.
It overheats in idle (with the fan running), on the highway at high speeds, and while driving slow. Sometimes it only gets about 3/4th to the red (usually when its cool at night) and sometimes it will hover just below the red; while I'm doing everything I can to keep it from hitting red (defrost on, revving engine). Some days it takes a little while to get hot and some days it happens very quickly. I'm tired of sinking money into the vehicle but as a recent grad I don't have the money for a new truck at this point. Suggestions included heater core clogged, water pump gone bad, fan clutch.
I drive a 2002 4-dr 1.6 L Accent and there is a strange, high-pitched squeaking that comes about from somewhere under the car at very slow speeds (30 mph or below). If I hit the brakes, the noise continues sometimes as the car slows. (The noise isn't the brakes, though, I know that), but if I hit the gas pedal slowly, the noise stops. Whatever is vibrating underneath doesn't seem to be causing a problem at high speeds. Or I just can't hear it.
Secondly, I am going to try to do some tune-ups for the summer for lack of better things to do, mostly, I can pretty much do anything (intake/exhaust, engine, electrical) as long as I can find detailed instructions.
For a while I had been having vibration at between 60-80mph I think I mentioned it in a thread before too. Well anyway when I got my 30,000 mi check up they told me it was probably due to the tires being unbalanced and that my tires were in such bad shape that balancing them woudln't make a difference. So I got to new tires (and my rims as you all remember) from NTB. I took it back to Toyota to get the alignment done after that I got on the highway to see if it was vibrating still and it was so they told me to bring back in.
So today they told me one of the tires that I got at NTB was bad because they couldn't get it balance within the range of the other 3 tires so I took the car back to NTB got into it with the guy there and they eventually saw things my way and put a new tire on the car. So after that I get back on the high way the car starts vibrating right when it hits 60. So I take back to Toyota, the guy tells, I heard him mention to one of the mechanics that it might be a bad axle.
Around 6:30 or so they call me and tell me they are going to take rims and tires off a brand new Camry and put them on my car and the manager who lives far away is going to drive my car home and then back again in the morning to get a better idea of the problem with the car. And to top that off they wanted to charge me 40 bucks for a rental car, but luckily I can drive my dad's Cam to work.
On my 09' passat wagon 2.0t: I've been on a couple of long highway runs and noticed that my steering wheel is vibrating slightly at higher speeds. Naturally I went for a wheel balance. They showed me one rim was slightly bent from a pot hole or something, but they were able to balance it and put it in the rear. Still a vibration. Took it back to the tire shop and they checked the balance again.
At this point I was still noticing the vibration and went so far as to swap the "damaged" wheel with another off of a passat with the same wheels. No difference noticed. Is it my imagination or is the steering so light in these passats that im feeling every imperfection of the road? I don't remember the car always feeling like this. I am at 14k miles and have the crappy stock good year tires.
for the last several weeks, I've noticed a problem that seems to be getting progressively worse... there is a vibration seemingly from the front end (possibly passenger side), and it only appears on the interstate at typical highway speeds (70-75 MPH). facts:
1. It does not happen below ~70 mph.
2. It doesn't appear to be a wheel bearing - no noticeable change in tone or "amplitude" while turning at speed.
3. I use cruise control all the time on the highway, and it is more noticeable going downhill (increases in vibration), when the engine is obviously off-throttle.
4. The car is a 99 V6 5mt.
5. The axles that are presently on the car are Raxles, and have been on it for ~4 1/2 to 5 years.
6. I recently changed over (this past weekend) to my winter/stock wheels and tires, but it was doing it with the summer wheels and tires.
7. It happens regardless if the gears are engaged or not (5th or neutral - I coasted down a hill on the interstate today in neutral to add more info).
8. I've replaced the wheel bearing on the passenger side about 6 weeks ago.
I'm thinking I have an inner CV Joint that is starting to fail. The boots are intact, as I inspected them recently while replacing the clutch/pressure plate/throwout bearing/flywheel. The transmission axle flanges had no play. The vibration was occuring prior to when I changed out the clutch.
Thoughts? Inner CV joint, or...???
Driving on the highway the other day and I was doing about 80 and I noticed that the front end started to vibrate pretty loud so I slowed down to around 70 and it stopped. I got home and called up the local tire shop had all my wheels re balanced as I heard that could be the cause they were near perfect. Tires have about 3,000 miles on them. so yesterday I took it out to see if it would do it again and I noticed when it starts to vibrate at about 80 and I push in the clutch it stops immediately. Could my clutch be going out? or possibly like the throw out bearing.
View 10 RepliesI'm having an issue with my wife's 2008 Camry. We're feeling vibration at highway speeds. Feels like it's coming from the front passenger side. We've had all 4 tires replaced (two of them replaced twice because we got lucky and the shop gave us a set of 4 for free with all the trouble we were having with the goodyear tires they sold us), and added hub-centric rings to her wheels. There are no noises to tell me whether it's a cv axle or a bearing. I've been under the car and the only thing I can find that comes close to loose is that the passenger side axle has a just a little more side to side play (runout - inner cv) than the driver's side.
View 11 RepliesMy 04 Solara 3.3L vibrates like crazy at highway speeds, but the vibration goes away after a couple of miles, only to return again later, and it isn't a tire balance issue. The vibration comes on quickly, and I have to hold the wheel with both hands, then it slowly diminishes and runs smooth again.
View 4 RepliesI have been feeling a vibration in my right rear at highway speeds (70+mph) At first i thought that maybe it was a wheel bearing but that would constantly be vibration and it wouldn't be off and on like it is. The car is on coils and a friend mentioned to check and make sure my right height is the same all around. I checked just by comparing the fender well gaps and it does seem as if the right rear is a bit lower. If this is the case, can ur car being a little lower on one side cause this vibration? if so, how?
View 2 RepliesSo about 5 months ago I started feeling vibrations in my seat and steering wheel. I got my tires road force balanced and it solved the issue. I just got back from a weeks long vacation in Maine. Before I left I had the tires road force balanced again to ensure a smooth ride up. I left some shaking in my seat so I wanted to get it ironed out.
While driving up my seat and the entire cabin shook when I exceeded 70 MPH, it got worse and worse the faster I went. The steering wheel didn't shake at all. I figured the tech balancing the tires did a bad job so I visited the BJ's in Portland. They re-balanced all my tires, I was present when the job was being done and noticed they were all out of balance.
The BJ's tech said it look like the shop that did the balancing over balanced each wheel (too much weight on each wheel). As soon as I hit the highway the same thing happened, shaking above 70MPH. At this point I determined it was probably a bent wheel. I visited a local wheel repair shop, they checked out both my rear wheels, since the steering wheel wasn't shaking I didn't bother checking the front ones.
It turns out both rear wheels are ever so slightly bent, they attempted the straighten out the more bent one. They tech repairing the wheel said he was surprised I even felt anything at all. So I had my hopes up that the problem would be fixed but as soon as I hit the road the same shaking returned. At this point, what's wrong with my car. I'm thinking of buying 4 new wheels, the car came from the factory with low profile 18 inch wheels which have been a curse.
A few more details about my car:
Toyo Proxes 4 Plus - Ultra high performance tires (Maybe contribute to harsh ride?) 20K miles on them
Installed thicker 20mm rear sway bar 6 months ago (But I never had shaking until now)
Installed front tower strut bar 6 months ago.
Total mileage 32K
I have hit lots of pot holes the past 2 winters lost 2 OEM tires and bent 1 wheel last year which was repaired.
Also I can't drive through it, the shaking doesn't stop with more speed it only gets worse. And the back end has started to feel squirrely over bumps.
i have a 2004 Mitsubishi lancer es 2.0 engine, and it's an automatic. I seem to consistently get a little under 23 mpg no matter how i drive. I've noticed that when going down the highway at 65 mph, it is at like 2900 RPM, is this normal? We also own a 2010 toyota corolla 1.8 auto and it only revs like 2400, and a 2005 xB that revs the same as the corolla, i'm just confused that with a bigger engine, it would rev so much higher.
View 6 RepliesI recently purchased the rims from another member here on Club Lexus.
Ever since installation, I have been experiencing a vibration at highway speeds and while braking. The wheels are correctly balanced.
My technician has told me that I need to buy a hub ring/spacer (not too sure what that is) but nonetheless, a grommet of such that fits between the backside of the rim and the frontside of the hub. I'm not too sure where to begin from there or what to even look for.
I bought 2012 Prius ii around 6 weeks ago. From day one I started noticing vibrations in the steering wheel most noticeable at highway speeds. I can describe this as high frequency vibrations that become very very annoying especially if you drive to work for an hour every day. This car has OEM Bridgestone Ecopia EP 20 tires. I took the car to the dealership twice already, they balanced the tires twice and road force tested it twice. They replaced front tires for me because based on the test results one tire was at 16 lb the other one at 19 lbs.
The new tires are at 8 and 10. They keep on telling me that this is by design and is a characteristic of the vehicle. However the Prius I test drove when I was buying it did not have this problem, otherwise I would never buy it. This vibration happens in any mode and I can even feel it at lower speed now though it is not as noticeable. I had a few people including Prius owners drive my car and everyone feels the vibration. With so many Prius models sold I highly doubt that everyone just accepts it as a feature.
I've been doing a lot of decently long highway trips this summer (5 hrs @ 75-80 MPH) and I've noticed that the 2008 VR6 Passat has some kind of pressure/wind noise/vibration above 75 MPH. It's hard to describe; it's like the noise you get when you open your sunroof too far and you get a harmonic noise from it. The sound seems to be coming from the upper rear of the car; behind the sunroof and almost from the rear glass.
All of the windows are up, the sunroof is closed and even the shade is closed to muffle the noise, yet it is there. However sometimes it isn't bad. If I have the radio on I don't notice it really, but when it is off it is very noticeable on certain stretches of highway. I'm having a hard time nailing it down as it is not entirely reproduceable. I don't know if it has to do with temperature, angle of the wind, climate control fan settings, what.
I did notice a few reviewers of the new CC complaining of a similar thing, which freaks me out that it is a design flaw - yet searching on here brings me up empty so I think it might be something I can fix. My first thought is that I have a tire slightly out of balance, yet the noise seems more wind related than tires.