Accent LC (2000-05) :: Transmission Won't Engage Gears
Aug 31, 2015
own a 2005 Hyundai accent 1.6L engine. I replace the engine today. The previous engine had internal damage. The transmission I left alone. I didn't disconnect the wiring. I only removed the engine. The transmission worked flawless. When I turned on the car the engine sounds great and the transmission sshifted gears and the wheels were moving. The speedometer worked so then I turned the engine off and lowered the car down from the Jack stands and tired it shine but this time the transmission did not shift gears. I lifted the car back up and did still did not shift gears. The transmission does nothing. The checked the guild level and it's full. What can cause a transmission to suddenly stopped engaging gear?
View 2 Replies
Advertisement
My 2000 Subaru Outback (75,000 miles) runs well almost all of the time. Every so often, especially when the weather is cold and I have been making many short trips, the transmission will refuse to engage into any of the forward gears (Auto-Trans). It will do reverse, no trouble, but not the forward ones. It does not do this with any sort of regularity or consistency. I have had it checked by my mechanic and he said that although it did this it sounded fine and was not shifting roughly. Thinking it might be a fluid pressure problem, he put in fluid additive to soften the seals and this worked for about a week, then back to square one. I saw enough notes posted on other forums by other Subaru owners to know that this might be an issue with this year's model--maybe some sort of quirk that I hope can be fixed without a new trans.
View 5 Replies
My 2000 Hyundai Accent, and it has started shifting gears when not traveling at the right speeds to do so.
I'll try to describe it the best I can, When driving I will be going whatever speed limit and all of the sudden it will make a winding noise (like when jumping on highway and pressing hard on gas peddle) and the RPMs will stall. It is like when shifting up, the car drives as normal but then it will shift down and pulls back (making a winding sound)
I am not sure what to do, I was told it seems like it may be the transmission is shot(I had the fluid flushed previously) and that it could cost over $1000 to get it replaced.
View 7 Replies
2008 Accent - driving down highway, heard a pop and car acted like it was in neutral. I have clutch pressure, you can see the hydraulic assist moving the fork, but gears just wont engage. I can free shift through all the gears with the clutch pushed in or not. Manual transmission and clutch kit replaced about 6 months ago when shifting fork broke inside last transmission and tore it all apart. With car in first (and turned off), I can push the car so I know gears are not engaging.
View 6 Replies
99 Passat1.8t auto, transmission doesn't engage into any gear ... Cluster shows that all gears selected ....
ATF level OK and VAGCOM doesn't show a ny codes/errors for trann When I put D or R - car revs up to 1200RPMs and thats it Checked ECU and TCU (tranny computer) no signs of water in them I don't really know history behind this vehicle but it had been sitting from 2009, had run before without problems (at least thats what previous owner told me) ...
View 7 Replies
i've got an accord 4 cylinder with an automatic transmission that does not engage any of the other gears when i shift it out of park. all indicator lights are out except for the park position on the dash.
View 1 Replies
Been working on tightening up the 3 on the tree assembly because shifting has become troublesome; not wanting to engage gears completely, tough to go from 1st to second and so on. I have already adjusted the linkage per the shop manual with no improvement and found that it was not misadjusted. One of the first tasks is to replace the bushings from the shift rod to shift level under the hood though the bushings have some play but don't look that bad.
I have noticed the amount of play in the column when in neutral seems excessive, between 2nd and 3rd I can move the shifter about 2-3 inches up or down from center without feeling any tension toward a gear. This I think is the shift collar. Before I go tearing into the column, after replacing the shift collar was the amount of play significantly reduced?
View 5 Replies
I have a 2003 Hyundai accent that was not shifting into higher gears about (45 mph) max speed. I took a transmission out of a 2005 ( same engine bad unibody) and put in the 2003. Making sure the torque converter was in all the way. Now I have no gears at all, no park, nothing. But the car does start. I went to the salvage yard and noticed that all the cars like it (hyundai) had no park either. So I must be missing something electrical right?
View 11 Replies
My friend has a 2007 accent with a manual transmission they said that they were driving and the transmission stopped shifting gears. The clutch pedal still has pressure so I don't think it is a master or slave cylinder issue. They freaked out and turned off the car and now the car will not start up again. Have any of you experienced anything like this before or know on this car where to start looking? I think the issue with not being able to switch gears could be a pressure plate issue but this would not cause the car not to start.
View 6 Replies
I own a 2003 accent and it would start then go but stall, when let sit for some time it would start back up, I have changed all two relays and pump and filter but now it wont start at all. I don't seem to have power to pump as I have hose off and when i turn it over no gas comes out of pump and no sound!!
View 1 Replies
That said my wife bought a 2001 Accent 1.6L Auto while I was overseas and it's been a great car, about 8 days ago it just crapped out. The reverse went out on her so we took it to get the codes read and on the way it went in limp mode, started hard shifting between gears and wouldn't go over 45 she says. Took it in to the stealership today and they said that the trans is shot as well as showing codes for P1527, P0732, and P0734. I know what the two slippage codes are and I can prolly just replace the speed sensors and that will be fixed but I'm not sure about the reverse and P1527.
View 4 Replies
Recently bought a `01 Accent 5 speed.. First question . How do I tell if its the 1.5 or 1.6 ? That will really point me in a good start. Ha... Ok.. Check engine light is on and I found a paper in the glove box with some of the codes wrong with it.. The one I focused on was telling me the fuel system was to lean . blah blah blah... Dont remember the exact code as I felt that my research was good and I replaced the MAF sensor... Didnt clear the code...
Also it was sputtering quite a bit in all gears mainly at low rpms. I did change the fuel filter , checked plugs and wires etc.. Now I replaced the MAF sensor and it has not solved the problem.. Took it to have it rescanned and have been given codes p1127 and p0136 .. both seem to relate to the Bank 1 sensor 2 O2 sensor. question is I have saw the "upstream" sensor located right below the exhaust manifold but did not see a second sensor?
From what I have gathered sensor 1 does the most work, so I`m curious if these 2 sensors are interchangeable? Could I buy the downstream sensor and if that does not solve my problem , take it out on try it in the upstream sensor? Also do you really feel as though just changing that sensor will "cure" my sputtering issue? the car only has 88k on it and seems to be in good shape otherwise.. I really need this check engine light problem fixed so I can get inspection..
View 3 Replies
What this may be. 2004 Accent Automatic. We just purchased recently for my daughters fist car. Today when leaving the house the car stays in first gear, you can move the shifter through the gears but it wont shift up. Reverse is fine. Checked the oil level in Neutral when hot and it was ok. Hooked up my code reader and there are no Codes. Car only has 85,000 KM on it.
View 5 Replies
I have the opportunity of getting i believe a 2004 accent gt for next to nothing. It recently lost reverse and all gears aside from first. The codes it is triggering are p0734 p0732 and p0733. Prior to throwing the codes it moved back but wouldn't budge forward. With codes no reverse or any gear higher than first. Car has 160k miles I am pretty mechanical. Should I run from this "cheap" "gas saver" or pick it up? With all 3 codes could it be just that sensor?
View 6 Replies
I don't like the way my transmission switches gears, is it possible to make the car change gears with 0.5 revs more then what it is right now... I feel like Hyundai only considered gas mileage for this car and didn't even think about the stress on transmission and engine...
I want the car to switch gears on higher revs then it is right now..
2012 Accent GS hatchback... Automatic transmission
View 3 Replies
2001 Accent 1.5 GL 165K miles.
The clutch doesn't engage until it's on the floor. I have to push real hard to allow the gear to engage. It then shifts... sometimes smoothly, sometimes it takes a hard push of the gear shifter, or it grinds until getting into gear.
I've changed the master cylinder twice in about 3 years but those times the pedal had no spring and just fell to the floor and stayed. Now, the pedal has spring (I push it to the floor and it springs back) so I assume the MC is ok. I even bled it with fresh fluid.
I'm not sure if the tranny fluid has ever been changed. Would changing the fluid fix this problem or does it sound like I need a new clutch? I'm guessing it needs a new clutch (or corresponding parts) since I've had two MC's go bad in a few years.
The pedal, even when it's shifting smoothly is pretty non-responsive and still engages a little mushy (comparing it to my 2012 Elantra 6sp).
View 4 Replies
Just the other day I was driving my car till I've noticed the gears started slipping. At first it was having some issues shifting through the gears (automatic transmission btw). As soon as I got off the highway, I parked in a parking lot just to check underneath the hood. Everything looked fine, went to pull out of the parking lot, no reverse. The gears started to slip up really bad. I noticed that the RPM's kept on reving up and wouldn't go any faster than 20mph. I went to an advance auto parts to get automatic transmission fluid. Still having the same issue and no reverse either. I had to park the car at a location to get it towed back to my house. Some people are saying my transmission is bad, some say it could be a real simple fix. Where to start diagnosing this issue. The car was driving normally until last Monday. My question is where should I start to check and what can I do to see if the transmission is completely shot??
View 33 Replies
I have a 2004 Hyundai Accent 1.6 DOHC 5-speed Manual Transmission ... so here is my problem;
Regardless of whether I am going from a complete stop or if I am simply changing gears the acceleration is practically non-existent, sometimes taking up to 3 minutes to accelerate just 5 mph. While I am driving at a consistent speed of 65 mph, the RPMs will randomly jump from 3000 to 4000 or 5000 with no apparent cause.
I have been told everything from putting air in the tires to replacing the clutch. I do not have the time nor the money to try every option of fixing this issue. I need to attempt to narrow this down to as few probable causes as possible.
View 5 Replies
I own a hyundai accent 2000 GLS, i have recently replaced the ECM wiring and a brand new ignition coil, however the engine still sputters when i try to accelerate in higher gears, my mechanic told me that the engine mounting bushes need replacement. is it one of the causes? the sparks plugs are new, fuel pump is working fine.
View 7 Replies
My standard 2002 accent is undriveable and at the mechanic right now (100,000km). For the past few weeks the car has driven very jerky. While in first and second gears if i accelerate too quickly it just jerks/slips and has very little power.
Yesterday the check engine light came on and i got codes P0300, P0302, P0303...misfire in cylinders 2 and 3. Checked this forum and decided to buy new spark plugs (last replaced plugs and wires 1.5 years ago). Got into the car and could go more than a block because it was jerking and then kept stalling. Replaced the sparkplugs and nothing changed. Had it towed to the mechanic...after a few hours he said he had cleaned the exhaust manifold and it was driving fine. I picked it up and a block away it stalled again.
The mechanic now says 3 of my fuel injectors need to be replaced and the fourth will probably go soon and it will be about $700 to fix. Does this sound right for these codes?
I called hyundai parts and they told me each injector is $236...he also told me he doubted they had to be replaced cause he has never seen an accent have fuel injectors replaced and also they rarely sell these injectors, he said it was probably something electrical.
I have found 4 injectors on ebay for $200 but is this really the problem? The mechanic says it is 100% the problem. But from reading the forum I dont think so.
Also wanted to add that i often noticed the smell of burning plastic. Smoke seems to be coming from spark plug area when i notice the smell but nothing looks burnt/melted.
View 14 Replies
I inherited this car from my grandmother when she passed. It has low miles, around 40k. Since I paid zero for it, I would like to keep it. Historically I have done all my repairs, but never trans work.
Here are the symptoms. The car has issues shifting into higher gears. I have to punch the gas and then it will switch gears. It then began to do this for reverse, and now now reverse does not work at all.
At first I thought it was a speed sensor problem, but when I took it in to be read, it came up with P0734. It could be electrical (Speed sensor?), low fluid (it's not low), or 4th gear.
Is this transmission worth me fixing or paying to have it repaired, or should I move on?
P.S. If I drop the pan and find shavings, I understand that to point to 4th gear and bearing (also what the computer code read as the issue). Do shavings mean it definitely is 4th/bearing, or could it be another blown part?
View 4 Replies
