I have a 2000 Accent that I changed the clutch and CV Axles on and now the transmission seams to be stuck. When i got done replacing the axles and installing the brakes I spun the wheels while installing the nut to aline the cotter pin. Once I got the car down, serviced the gear oil, bled the clutch master. Went to drive the car and it wouldn't move .
View 5 RepliesBought a 2001 hyundai accent 1.3 si petrol manual 2 weeks ago. After pulling off today, i went to go into 2nd gear, and I couldn't move the gear stick. I parked up and turned the engine off, then started the ignition again. When the clutch is in, the gear stick will not move in any direction, its completely stuck, but when the clutch is out, the gear stick will move in all directions.
View 6 Replieshave had this car for 2 years with out any problems whats so ever. Drove home from work today parked in drive went to leave again and transmission is stuck in first will not shift.
View 10 RepliesSo yesterday, this had happened for the third time in 3 years owning this car. Unhooking the battery for 20-30 minutes resets the computer and it is ready to go for a while with no issues. This has become annoying though. What is causing the car to enter "limp" mode and stay in third gear? One time it happened, I brought it to AutoZone and they did a scan and came up with the speed sensor. I haven't replaced it because it didn't happen for a while after that.
View 11 RepliesI have a 2001 Hyundai Accent with 120,000 miles on it. Up until a few months ago, its been a great little car. The transmission started acting funny by shifting irregularly and then getting stuck in 3rd gear occasionally. I took it to the dealer and they told me that the tranny is shot. The estimate for the repair is $2000.00.
I just can't see putting that much money into this car. It needs Struts, Shocks and a timing belt. Basically what it needs is what its worth if it were running well.
How hard it is to replace the transmission in this car? I have the 1.6L DOHC with the Automatic transmission.
My mechanic told me that something was wrong with the driver's side front axle of my 1990 Mazda 323, which has been a dream car for 21 years. He got a new axle to put in but could not get the old one out. Now it is at another mechanic's, and he also can't remove the old axle. He says there is a pin on the end and it is stuck inside the transmission (a 5-speed manual transmission). He has broken the axle trying to remove it, and now it cannot be driven.
View 19 Repliesif a 2002 4x2 ford ranger was towed into a shop because the clutch failed is there anyway the #2 syncro or anyother internal part of the transmission could be damaged while the service department repalced the clutch?
View 1 RepliesI have a 2004 Hyundai Accent 1.6 DOHC 5-speed Manual Transmission ... so here is my problem;
Regardless of whether I am going from a complete stop or if I am simply changing gears the acceleration is practically non-existent, sometimes taking up to 3 minutes to accelerate just 5 mph. While I am driving at a consistent speed of 65 mph, the RPMs will randomly jump from 3000 to 4000 or 5000 with no apparent cause.
I have been told everything from putting air in the tires to replacing the clutch. I do not have the time nor the money to try every option of fixing this issue. I need to attempt to narrow this down to as few probable causes as possible.
I recently bought a accent, changed the oil then upon starting it back up it just pours out white smoke from the exhaust. i might have put a little too much oil in, would that cause the issue? It didn't happen before the oil change either.
View 6 RepliesI have a 2000 Ranger
The door sticker has an axle code 97
What is the gear ratio?
I own a 2000 Hyundai Accent with 85,000 miles on it. I recently took my car into a local shop because the pressure on my brake pedal was extremely low. I was almost pushing it to the floor. On my first trip to the shop, they replaced the rear wheel cylinders because they were leaking. This replacement didn't fix my problem.
On the second trip to the shop, they replaced my master cylinder. I did call around to other shops to do a price comparison and the price was reasonable on both jobs. This work was done about two weeks ago.
At first, this seemed to fix my problem, the pressure was perfect. Since then I've been having an intermittent problem with the brake pedal pressure changing. It would get a little hard during driving, but would correct itself after a few moments. I don't drive that often or very far, so I was waiting to see if the problem would get worse.
Last night it did. I went out and when I tried to drive my car home my pedal was extremely hard. I could barely push it. While I was driving my car home (I was close to home), it felt like I was driving with my brakes on. My car would stop as soon as I took my foot off the gas pedal, I could not coast. When I got out, I could feel heat coming from the front tires, which I didn't even have work done on. There was also a smell that I've never smelled before. It almost smelled like something burning.
I was told I should have my car towed back to the shop on a lifted bed and not rolled there and that they should fix my car at no charge because they did something wrong.
My ultimate question is did the shop do something wrong and should I take it back to them if they did? Should they be responsible for this new repair? I don't want to go demanding anything if it's possible this is a whole new problem and not their fault. Even though it does seem like an awfully big coincidence. My next question is: what could be possibly wrong with my car? I would like to know what I'm getting myself into.
I'll drive my 2000 Ford Ranger, 4cyl XLT about 5 miles to the store without a problem. On the way home, after a few miles, the clutch pedal will either jam at the top, or go all the way to the floor without engaging the clutch. If I wait 5 or 10 minutes, the clutch pedal will start working again for a short time.
If I feel the clutch pedal starting to misbehave, if I ride the clutch and don't release the clutch pedal all the way, and if I don't push the clutch pedal all the way down, I can keep driving the truck. As soon as I release the clutch pedal, it will jam up again, or the clutch pedal will go all the way to the floor without engaging the clutch. I don't like riding the clutch, but that seems to be the only way to get home once the clutch pedal starts jamming.
It certainly seems related to the engine warming, or heating up. Sometimes, after the clutch jams up, I'll wait 5-10 minutes and the clutch pedal will start working as if nothing every happened. So, it can't be strictly a hot engine, hot clutch fluid issue, right?
What would you attempt to replace first, the Slave Cylinder? The Master? Changing the fluid? Shooting the truck!?
I have an Accent 2005 model with problem (speedometer) not working at all... All gauges are stuck (RPM, Speed, Fuel & Temp) also no mileage digits appear. I already check fuse. I remove speedometer cables and connect it again, also clean it and change the bulbs but still same...
View 14 RepliesThe a/c on/off button seems to be stuck. If I push it the whole switch moves. This happened after removal of the fascia for a radio mount job.
What could be the problem? Can I maybe override it? It is no problem if it always works when the fan is on.
I bought a used accent 1.3 before few months , with 100k miles on the clock. I did all the basic maintenance stuff, oils, filters, spark plugs, coolant, timing belt etc... I replaced the clutch disc also, because it was slipping.
The problem is that the clutch engage with a knock sound, just like when you have a loose engine mount. But... if i stay with clutch pedal pressed for a second, do the shift and released, the clutch engage smooth and all works fine. So, that's the way I do shifts for now.. Is this a flyweel problem?
i have a 2002 accent 4 door and it's stuck in park, its an automatic. I removed the park override little cover thingy next to the shifter and released it out of park but when I put it back in it got stuck again.
View 5 RepliesMy clutch makes a hissing sound whenever i press it down while driving, its working fine, but am worried about the sound, i checked the master as well as the slave cylinder and there is no leak. Plus how do i remove the moisture from my headlamp.
View 3 Repliesl have a 2000 model accent and the air conditioner compressor clutch is not engaging . you press the 'AC 'button and the indicator comes on when a fan speed is selected which l am sure is the correct operation.l checked for 12 volts at the coil terminals of the relay and there is no 12 volts.l shorted the switch contacts of AC relay and the compressor did engage so the wiring from the relay base to the the compressor clutch is ok. l also checked the contacts of the 'AC' switch itself and it seems to be ok. l haven't had much luck with sorting out the wiring from the switch to the relay as l do not have a wiring diagram.
View 4 RepliesI have just changed my clutch and machined my flywheel on my 1.5ltr 16v dohc 2000 lc accent. I used all the correct trans fluid and refilled and bled the clutch fluid. It takes of from lights like a new car but if you put your foot down around 40kph it revs out a bit and does so through all gears untill you reach a bit of speed. What is going on?
View 11 RepliesGot it on the motorway to find the passenger window had dropped slightly when shutting the door.. And on pressing the electric window buttons, the passenger and two rear windows aren't working! The driver window opens and closes perfectly fine. Looks as though the window lock button is stuck on, but pressing the button makes no difference as though there's a loose connection.
Might this be a fuse problem with the locking mechanism, or what may have caused this and if I can fix it easily, or whether it does need to go back to the dealer.
2001 Accent 1.5 GL 165K miles.
The clutch doesn't engage until it's on the floor. I have to push real hard to allow the gear to engage. It then shifts... sometimes smoothly, sometimes it takes a hard push of the gear shifter, or it grinds until getting into gear.
I've changed the master cylinder twice in about 3 years but those times the pedal had no spring and just fell to the floor and stayed. Now, the pedal has spring (I push it to the floor and it springs back) so I assume the MC is ok. I even bled it with fresh fluid.
I'm not sure if the tranny fluid has ever been changed. Would changing the fluid fix this problem or does it sound like I need a new clutch? I'm guessing it needs a new clutch (or corresponding parts) since I've had two MC's go bad in a few years.
The pedal, even when it's shifting smoothly is pretty non-responsive and still engages a little mushy (comparing it to my 2012 Elantra 6sp).