Accent LC (2000-05) :: Tranny Shifting Into A Lower Gear And Get Stuck While On Freeway
Sep 5, 2013
My problems started out around the beginning of the year. Mostly, it was the transmission. It would slam really hard when shifting. Worst, sometimes while on the freeway, it would shift on it's own, for no reason, into a lower gear and get stuck. (Happened twice and was really scary).
Along with this, a couple times I would start it up and it would rev really hard, about twice what it normally would.
Usually, with the revving, I could turn it off and back on, and it would stop. A few times I could disconnect the battery, reconnect, and it'd be fine.
As for the tranny, I could turn it off then back on and sometimes that would work. Other times after a few miles it'd work itself out.
I did take it to my local Hyundai dealership. The first few times they couldn't get any code to pop, and they couldn't simulate the issue. It was very random when it'd happen. Luckily, on the 3rd try, they did get the tranny to shift hard. They said it was a bad tranny and replaced it (free due to warranty).
Unfortunately, that hasn't gotten rid of the issue. After a few months... maybe 3K - 4K miles the issue is back. Again, it's very random.
I've had the high revving which I've had to disconnect the battery to resolve. And the tranny is slamming again.
I don't notice any other issues. No engine light (except the one time the engine was revving really high and I had to disconnect the battery to reset, then the light went off).
Sometimes I can go a month with no issues. Sometimes it'll happen back to back days.
Could it be a computer issues? Is that something I can fix/change out as a novice?
View 10 Replies
Advertisement
I have a 2001 Hyundai Accent with 120,000 miles on it. Up until a few months ago, its been a great little car. The transmission started acting funny by shifting irregularly and then getting stuck in 3rd gear occasionally. I took it to the dealer and they told me that the tranny is shot. The estimate for the repair is $2000.00.
I just can't see putting that much money into this car. It needs Struts, Shocks and a timing belt. Basically what it needs is what its worth if it were running well.
How hard it is to replace the transmission in this car? I have the 1.6L DOHC with the Automatic transmission.
View 12 Replies
My friend told me the other day her car was in overdrive (hwy driving) and suddenly, it shifted to a lower gear. It seems no one knows why. She does have an extended warranty, but the garage might charge her $300 to open it up to see what is wrong. Another friend suggested a clogged filter. Another one, a sensor.
View 7 Replies
I recently bought a 2002 Accent with the 1.6 auto 133000 miles. I have been reading the postS around here about the crappy transmission. My car seems to have some life in the tranny still but it has slipped from 3rd to 4th gear around 45 mph when i get on the gas too hard. Its also a little sluggish to start off. My question is should i change the fluid out knowing i have a slipping issue? The reason i ask is that last time i changed the fluid and filter on a Jeep that was slipping i ended up having to rebuid it. Is that a real possibility if i change the fluid in this Hyundai?
View 3 Replies
I had the transmission rebuilt a year and a half ago, when I took it in it came up 4th gear incorrect ratio. The guy who rebuilt it said it wasn't the original tranny that came with the car because it was modified to fit in the car. When I got it back, after a couple hundred miles or so, the check engine light would come on for a day or two then go off. When the check engine was on it would get stuck in 3rd gear, once the light went off all was well until the next time. I took it back to the guy who rebuilt it since it was still under warranty. the P1529 code came up for TCM issue. He put some sensors and a chip in and thought it fixed it, no such luck. Finally I had the cash and had it looked at by another shop and the 4th gear incorrect ratio came up as well as the P1529 TCM code. He's suggestion to fix it was to either get a used tranny or rebuild this one again. He believes since it isn't the original tranny that the tranny in there now was for a SOHC engine, not a DOHC engine and that's why the ratio in 4th gear is off and it throws the TCM code.
View 6 Replies
I have a 2005 Accent GL (4dr Sedan) base model, 5 speed. I live in Canada (not sure if that will play a part); I notice that when I shift from first to second there is a 'clunk', not really a grind, and not a major clunk... but it's noticeable. As the car warms-up, it seems to be less pronounced (or maybe I start to ignore it). Is this something to worry about? or could it be the clutch plates.
I have had lots of bikes with wet clutches and this is 'normal' for a bike going into first gear. With the bike it's due to what I call Hydrolic-stick ... (2 or more) plates 'sticking' when you let the clutch out, one spinning faster than the other. Off topic now...
View 5 Replies
I am having a few issues with my 2001 accent. I bought this car for around 500 bucks after my friend hit 3 deer with it. At 101,000 miles the transmission went on it and he had it replace with a new one. At about 113k he hit his third deer and parked it. I bought it off him a few years later and its been running great. It died on me one time and it was the crank position sensor. Now I have about a 156k mile on it and it will not go into overdrive.
I have gotten mis fire codes, I know it needs new O2 sensors, and also P0733 Gear 3 Incorrect ratio. The button on the shifter does nothing, If i press it on or off the light does not come on on my dash. I noticed it was not going into OD this last winter if i dropped it into low and shifted to drive it would no longer go into overdrive until i placed it in park and then drive again. Ive been searching everywhere for an answer I was reading one post that it could be the TPS sensor causing issues but i haven't had time to check the voltage.
View 5 Replies
I have a 2005 Hyndai Accent GT automatic (83,000 km) and I am having a problem with the gear shifting. It's happening more and more.
As I am driving I am pretty sure that it's changing to a higher gear but when I slow down it seems like its not shifting down at all. Coming off the Highway I have to slow down and when I speed back up it seems like its still in the high gear. The RPM's instantly jumps up.
The only way it fixes it self is when I pull over and shut off the car and then start it up again and I am fine. A friend at work said that I may have to have my transmission fluid checked and filled up.
View 7 Replies
The Accent has been working great recently until the other day when I got in to go to work and now it suddenly shifts very hard into 2nd. And sometimes 3rd.
This problem seems to come and go. Sometimes it will shift smoothly. Other times it will have to reach super high rpm and I will have to let off the gas and slowly accelerate to get it to shift. This seems to happen throughout all the gears and it does not make any difference if overdrive is turned on or off. Also reverse works just fine.
I checked the fluid and it is at the proper level. It does seem to be a little dirty (not burnt) so I am planning on changing the transmission fluid, but something tells me that is not going to solve this issue. It seems like an electrical issue to me. What it could be?
There are no codes at all on the car. Don't know if it matters but the car just turned over to 100k miles. I've been reading on here about all the problems the automatic trannys have in this car but 100k seems a bit early to have any serious transmission problems.
View 1 Replies
have had this car for 2 years with out any problems whats so ever. Drove home from work today parked in drive went to leave again and transmission is stuck in first will not shift.
View 10 Replies
I drive a 2002 Accent GL, automatic transmission with only 86,000 on it. For a while now I've been having transmission issues where the car will jerk violently when shifting or starts to rev in certain gear or in park. It also doesn't seem like it knows what gear it wants to be in half the time when I accelerate. Recently, while driving somewhere, it got real worse. It started revving and jumping and redlining and just going crazy while I was driving. I turned the car off and waited a while and turned it back down and it seemed to calm the issue a bit.
But I am afraid to drive right now. It's not the fluid. I've changed it twice in the past two years. Never works. I've seen issues like this on here before. If it IS the transmission needing to be replaced, why so soon with just 86,000 miles on it? And would having the transmission rebuilt be a better choice, cost-wise, but still just as effective?
View 7 Replies
So yesterday, this had happened for the third time in 3 years owning this car. Unhooking the battery for 20-30 minutes resets the computer and it is ready to go for a while with no issues. This has become annoying though. What is causing the car to enter "limp" mode and stay in third gear? One time it happened, I brought it to AutoZone and they did a scan and came up with the speed sensor. I haven't replaced it because it didn't happen for a while after that.
View 11 Replies
My wifes 2001 Accent at slow speed seems to change into its gears ok. But when at normal driving speed, it seems to hang I believe between 3rd and 4th grar. If you let off the accelerator a little, it will change, kinda hard into gear.
Also, when decelerating, it seems to "surge" when going from 2nd to 1st and almost acts like it wants to die. this is an Automatic Transmission.
Things I have tried: replaced flex exhaust and reset a P0133 error code. Condition still exist after 100+ miles of driving. Tried cleaning MAP/MAF sensor, PCV valve. It will not showing any more codes or check engine light with this current condition. I am at a loss as where to go next for diagnostics. If I just had a code # to work off of....
View 20 Replies
I just bought this transmission from a reliable parts dealer. Should have about 50k miles on it. Looked really clean when I got it.
The guys who put in the tranny cracked a speed sensor, so I bought a new one and put that in. I dried off the sensors and screwed them into their spot on the tranny after removing the intake filter that was in the way.
Even with the new speed sensor the car is still doing the following:
1) Does not go into reverse until I've gone into drive for a couple seconds, pulling forward. Reverse does not work. However, when I unplug the speed sensor reverse works right away, but we still experience the following...
2) car goes from first to second gear to third gear smoothly, as it should. Seems really smooth like a car should shift! However... it won't go past 3rd gear and then it won't downshift! So, even after stopping and idling, I can't leave 3rd gear.
3) When I turn the car off, then turn it right back on, I can go through first, second, third gear again then... it stays in 3rd gear.
Another issue that has come to my attention since I got the car back, is the steering wheel shakes pretty hard while idling with no gas. While driving it seems smooth -- idling again it shakes heavily. what could they have damaged while putting in the tranny to cause this shaking?
So far as the funny tranny stuck in 3rd gear, it seems to me like it's a computer issue? But, what could be the cause? What tests can I do to determine the cause of this problem besides the ones I've run so far?
View 17 Replies
Bought a 2001 hyundai accent 1.3 si petrol manual 2 weeks ago. After pulling off today, i went to go into 2nd gear, and I couldn't move the gear stick. I parked up and turned the engine off, then started the ignition again. When the clutch is in, the gear stick will not move in any direction, its completely stuck, but when the clutch is out, the gear stick will move in all directions.
View 6 Replies
My 2006 Elantra (54,000 miles) shifts really, really hard when it's not cold and passes through the 35 mph range -- hard enough to make you glad you've got your seatbelt on. I've taken it to my regular mechanic and now it's in an automatic transmission shop.
My mechanic changed the fluid (twice), and took it through a "learning sequence". The fluid didn't look that bad and he reported that there were no codes to work with. He thinks I'm going to have to get a new transmission.
The AT shop has confirmed that there are no codes to work with and that the problem begins at 143 degrees. They tell me that the transmission is shifting into a higher gear without releasing the lower gear. They tried replacing a couple of solenoids, but that yielded no change in behavior. Now, they're telling me they "think" I need a new computer. I'm just afraid the trial & error approach is going to cost me a boat-load.
View 1 Replies
I have a 2014 2.0T AWD Limited, now it's about 9000 kms so far with regular maintenance at dealer. Recently I have found the tranny is shifting a bit lagging, in particular shifting from 1st to 2nd gear. I didn't think it was like this when it was new, not sure if it's something wrong, or now I'm getting more used to the shifting and start complaining.
View 3 Replies
I unhooked the battery for about an hour. I hooked it back up. I started the car put the selector into drive. CLUNK. Disengaged the parking brake. Drove. It turns out when I shifted to D it went straight to third and stayed there. I turned off the car, restarted it. Still stuck in third. Drove a few miles. Restarted it. No more issues. My guess the tranny went into safe mode, but why?
View 3 Replies
I have a 2002 Camry with (440K Kms) and automatic transmission. I am the second owner and had this car since 130K Kms so I have been driving it for a while. The car was in great condition but recently, the transmission started to give some trouble where it's gear changes were not smooth. Also, when I would come to a complete stop, trany would go into neutral even though I have not touched the gear shifter and it is still in drive.
I had my mechanic drain and fill transmission fluid since it was a bit dirty. A few days later, the car would park with gear box in "P" but no matter which gear I would put the gear shifter into, it would remain in neutral and won't pick up into any gear at all. So, I parked the car on the driveway. Couple of days later I wanted to try to see what the issue was and now, no matter what gear I put the gear shifter into, it stays into park.
View 14 Replies
Seems like the problems just keep building up. Today leaving work T-reg shifts fine untill it got to 5th gear. It was around 35 mph. Went to give it more gas and it never shifted out of 5th to a lower gear. It did accelerate but even with pedal to the floor it never downshifted. Whats going on. It has done it twice in the past two days. After only having it on the road for less than 5 min each time.
View 6 Replies
My 99 V6 with Tip just started to malfunction this past weekend. By malfunction, I mean when I shift over into Tip mode, the display remains on automatic and even shifting up and down will not change the tranny gear.
I was driving with the cruise on and shifted into Tip mode to slow down for a toll booth ( slow to 25 and not stop all the way). When I got through the booth, I hit resume on the cruise forgetting I had shifted into tip and the car revved back up to 65 mph in 3rd gear for about 5 seconds ( I had the stereo cranking and couldn't hear the engine)before I realized what I had done.
I tried to upshift in Tip but it wouldn't let me so I had to go back to full auto setting where it works fine.
Is it possible to burn out a fuse or circuit of some kind by doing a dipshizit maneuver like that? The car runs great otherwise and still is getting low to mid 20's mpg in spite of the ethanol crap.
BTW, just had the computer reflashed last week after putting a new battery in because the Throttle Body was not working properly.
View 2 Replies
