Accent LC (2000-05) :: Tapping Sound When Idling
Apr 14, 2015
I have a 2000 Hyundai accent. Bought the car used at a lien sale over 3 years ago, with about 120k miles on it... it now has over 197k miles on it. I have changed the oil and filter religiously since I bought it, using Castrol GTX High mileage 5w30 synthetic motor oil. I have also (in the last year) replaced the plugs with platinum plugs, the plug wires, and the air filter. A the car has always made a tapping sound when idling since I bought it, but recently (in the last week), it makes little shoemaker sounds when I accelerate. I used to associate this with detonation and adjust timing (back in the day when you could put a timing light on a car and turn the distributor to set timing). Since timing is now controlled by the computer in the car, am I right in assuming that I need to replace the timing belt?
View 4 Replies
Advertisement
I have a 2010 Accent. My Accent has a tapping sound when the engine is cold. I have read on this site that others have had this problems and it was the chain tensioner. I was wondering if this was something Hyundia would fix for free or how much it cost to get this fixed. Is there a recall for this problem? There appears to be a problem with a chain tensioner on the 2010 model of Accent.
View 26 Replies
I own a 2001 Accent 1.6, auto. 150,000 well-taken-care-of miles. New plugs/wires/timing belt/coolant flush 10,000 miles ago. Most recent oil change was with Shell Rotella T5 (I believe 10w-30 blend) and Purolator PureOne filter, 4-5,000 miles ago. It does not burn any oil, and runs very well. It has never been low on oil, revved high, or abused in the 10,000 miles I've owned it (except an ebrake u-turn on a dirt road to scare the wife )
The engine has always had a mild tick when cold, that goes away within about 30 seconds. Normal, from what I could tell. Also, it has always had a tick from roughly 1500-idle when releasing the gas, in neutral. Again, seems fairly normal for a little engine, I figured just some valve noise.
This morning I started the car (sat overnight) and it idled a bit rough for about 20 seconds, and I noticed that the ticking from before was now closer to a knocking/tapping, nowhere NEAR the horribleness of a spun rod on my WRX . But it was still a bit alarming. It never really quieted down, but as I rev, the sound goes away completely above 2k, and the flutter when I release the throttle is louder than before.
View 11 Replies
I've got a 2001 Accent 1.5 liter 5 speed. Car has 105,500 miles. Whenever the car is running, it makes an irritating tapping noise somewhere on the left side of the motor. I've been told that it sounds like the timing belt, but the car runs perfectly, doesn't miss. The tapping used to go away 30 seconds to a minute after starting it, but now it's constantly there and slightly louder. The noise goes with the rpms. When the rpms are higher, the tapping is faster. I've also noticed some loss of power. I recently added some octane booster to the fuel but noticed no difference. My uncle told me it may be a main bearing starting to go out but the tapping does not have a metallic tone of any.
View 3 Replies
My accent had been sitting neglected for a few years. I decided as a side project I would get it in working order before winter and do more to it next spring. The car had a rough idle when started but I had ran it nearly all day a few months ago.
Last week I changed spark plugs and a few other minor things. The undercarriage was wire wheeled and coated with POR 15. This weekend I added gas (with gas cans, car is off road currently) and added techron fuel treatment. The car took two tries to start (always two) so I changed the fuel filter and that problem went away. However, I noticed that when the car idles it begins stalling when it reaches temperature. Thermostat says car is not overheating.
After 15 or so minutes of idling the car just cuts out and SOMETIMES will start but usually it just cranks and cranks. If I wait a bit it will start up again but will die more quickly and this will keep happening until I let it cool. I am also noticing a fairly loud clicking sound from behind fuel injectors. Not the injectors themselves but somewhere behind the fuel injector rail. I am unsure if this had been going on previously or if it is a symptom of the stalling problem.
I cleaned throttle body, IAC, crank and cam sensors though no error codes to speak of. Rough idle takes a few minutes as at first the engine is smooth.
View 8 Replies
What happened was, the car was not starting (its a manual, so I can push start). I replaced battery but accidentally put it in with the neg connected to pos post and pos. connected to negative.
The car was off when i did it so as far as i know I only blew a couple fuses. So I replaced the fuses and now the car is idling really high. So I cleaned the throttle body, still idling high.
Now, the car wont start unless pushed and I have no ac/heat (the fan has no power).
I have checked all of the fuses and they are fine. I have also tested the Throttle Position Sensor, it is fine.
Could it be the diodes, relays???
View 3 Replies
2000 Hyundai Accent GS, 1.5l, 4cyl SOHC...
I have a slight issue. A few weeks ago, I put some "STP" style fuel injector cleaner into my gas tank. Either A) It cleaned everything really well and clogged my injectors, or it turned into gunk and possibly clogged something else up.
Ever since that day, my issue is that the car "stutters" very slightly. When idling, it'll "hiccup." When I'm doing normal driving, 55-60mph at 2k RPM, It'll almost feel like a transmission slip.
I've went and replaced my Fuel pump, filter, and now I've done half a can of seafoam through the brake line power booster (vaccuum) straight into the engine, and the other half into my oil for further cleaning. I also applied Seafoam Deep Creep into my throttle body, just for further maintenance.
Ever since then, everything has been running noticeably better, and I've had a huge increase in gas mileage, but there's still a slight hiccup that occurs during idle and driving.
I change the oil /filter, plugs, wires, air filter on a regular basis.
I also had to change the MAF at one point in time, as it died and the car wouldn't start at all.
Next thing I'm thinking about doing is changing the plugs / wires one more time (it's been about 5 months since my last change) just to see if I bought a faulty plug.
The car was put on a computer and the only error code that came up was one about my check engine light being out.
View 3 Replies
I just bought this transmission from a reliable parts dealer. Should have about 50k miles on it. Looked really clean when I got it.
The guys who put in the tranny cracked a speed sensor, so I bought a new one and put that in. I dried off the sensors and screwed them into their spot on the tranny after removing the intake filter that was in the way.
Even with the new speed sensor the car is still doing the following:
1) Does not go into reverse until I've gone into drive for a couple seconds, pulling forward. Reverse does not work. However, when I unplug the speed sensor reverse works right away, but we still experience the following...
2) car goes from first to second gear to third gear smoothly, as it should. Seems really smooth like a car should shift! However... it won't go past 3rd gear and then it won't downshift! So, even after stopping and idling, I can't leave 3rd gear.
3) When I turn the car off, then turn it right back on, I can go through first, second, third gear again then... it stays in 3rd gear.
Another issue that has come to my attention since I got the car back, is the steering wheel shakes pretty hard while idling with no gas. While driving it seems smooth -- idling again it shakes heavily. what could they have damaged while putting in the tranny to cause this shaking?
So far as the funny tranny stuck in 3rd gear, it seems to me like it's a computer issue? But, what could be the cause? What tests can I do to determine the cause of this problem besides the ones I've run so far?
View 17 Replies
Owning a Hyundai. I have a problem and it seems to be pretty common but haven't gotten anywhere with it yet. Last week my 2004 accent 1.6 manual transmission started running rough. It was idling higher than normal and while driving would not go past a certain rpm (about 2500 if I had to guess,no tach). On the way home from work it was running this way and then started badly misfiring and shut off, when attempted to restart it would not. I pulled the codes with a scanner and got p2400, p0562, and p0121. I charged the battery and replaced the throttle position sensor, still won't start. I can hear the fuel pump kicking on when I turn on the ignition. Also found the ecu 1 fuse blown, replaced it and continued to attempt to start with no luck, fuse was blown again. Like I said I haven't owned the car long and I don't know much about it. I am not sure where to go from here and I don't know how all these symptoms are tied together.
View 42 Replies
I have got a hyundai accent and I was getting a really annoying rattling sound from the boot i have been looking every where to find it and today i have sust it out if you open your boot up and just drive it round the block and it does not rattle then its probably the same problem that i had its the catch that the boot locks on to they must of been a bit of a gap to it and the metal was rattling together on the clip and the lock all u have to do to fix the problem is open your boot up then on clip on the car that the boot locks on to simple apply some installation tape around it so its pretty thick but not to much close your boot and problem solved it should be ok mine is fine now back to silence again now instead of a annoying rattle when driving.
View 1 Replies
I just had lots of work done on my car, and since then the Hyundai radio (HM5064) is not working. I thought I just needed to put the radio code in again, but when I went to do that today, all the LEDS are showing for the stations, time, Cd etc.There is just no sound.
View 5 Replies
My clutch makes a hissing sound whenever i press it down while driving, its working fine, but am worried about the sound, i checked the master as well as the slave cylinder and there is no leak. Plus how do i remove the moisture from my headlamp.
View 3 Replies
My 2005 Accent started making this weird slapping sounds last night. I hesitate to call it knocking b/c it's not that loud. It sounds almost like if you put a some cards in the spokes of a bicycle (weird description, I know). But basically the sound speeds up as I accelerate and vice versa. It started last night as I was pulling up to the house. When I opened up the hood, it sounded like the sound was coming from the top/top back of the engine. I recently had all belts and radiator (small leak) replaced about 2k miles ago. What it may be? Car only has 67k and I drive 95% on the highway at about 70mph. I drove my truck to work this morning so I don't make the problem worse until I know what it is.
View 1 Replies
This start this morning on my way to work. When I took my foot off the gas I would hear a clicking knocking sound the sound slowed down as the car slowed down. Any time I took my foot of the gas this would happen. Was still there when I hit the break. If i had my foot just barely on the gas it would go way. Its an automatic 2000 Accent 156K miles.
View 20 Replies
Ignition turns over, but no sound. There is power to lights, radio, etc. Tried a boost, thinking it was battery, but the boost was unsuccessful. Tried using the spare key but that was also unsuccessful.
The tow driver said it sounded like a fuse or clutch safety sensor. I also heard that it could be the battery leads. We're fairly new at fixing the car ourselves, learning as we go, so not knowing some otherwise basic things, like how to clean and tighten battery leads, what fuse to change, or what the heck a clutch safety sensor is.
View 5 Replies
Have replaced BOTH half axles. Clicking sound present when driving - does NOT change when turning right or left. Seems slightly affected by acceleration/deceleration - makes clicking slightly louder/quieter. Clicking is DIRECTLY proportional to speed - slows down until car stops. Transmission works fine, fluid level is correct. New trans fluid and filter. What the heck could this be? Wheel bearings seem solid - jack up car and try to wiggle wheel - solid as a rock both right and left sides. WHAT ELSE COULD THIS BE???
View 4 Replies
I bought a 2005 Hyundai Accent about 5-6 months ago, GS 2 Dr model, 52,000kms (69,000 on her now), and lately she has been making a weird ticking sound form the engine when idle, if you give her some gas it slowly goes away as your RPMS increase. I had my father look at it, he said it seems fine, i also had a garage look at it and they also said its fine, but too me the engine sounds different then it did when i got it, maybe the cold from the winter could be doing this? when the engine is heated up it still makes the noise.
View 4 Replies
My '03 gives a rattle sound under load/acceleration conditions. This does not happen during the warm up period, so it appears that the engine runs lean under acceleration. There is no check engine light on for this. Approx 172k KM, (100k miles). The noise appears worse when it is hot/humid outside. I have run a can of Seafoam through it (half in the crankcase, half in the fuel line), and that doesn't seem to have worked. Therefore, I don't think that it is the injectors. Possibly fuel filter (still original)? Any easy way to test?
View 8 Replies
This started a few months ago. At first it only happened when making a hard right turn, its a repeated click or grinding noise. Over time it has gotten worse, and now happens when turning either direction, and its worse the faster the car is going. Turing into the parking space at our apartment is fine... turning from one street to another going to work is not. Various things I looked up suggested the cv joint, but when I went to parts stores websites to look up prices all it gave me was cv boot kits in the results. Is this whats actually wrong, and is it something easily fixed for a DIY person?
View 7 Replies
Came off the highway just now and there's a tapping sound coming from the engine. It's louder than the ticking these engines make so believe me it's nothing I've heard before. No codes, no overheating and doesn't seem to be anything else wrong. I am due for an oil change soon and I'm wondering if that could be it?
The engine wasn't cold obviously. I did shut off the car and then back on and it still did it. Just want to make sure my engine isn't going to explode anytime soon!
View 11 Replies
2009 Accent with a manual transmission
I am at about 65K miles so far. I changed my oil last night like I normally do. The car was on rhino ramps and as I started the car to back off the ramps, I noticed a very audible, "Tap tap tap" noise on start up, only. It goes away a second after I let off the key turn once the engine catches.
It did this when I backed it off the ramps and then when I shut the car off and waited a minute to check for it again on level ground and the same thing happened. Only two times and it has been quite as a mouse on start up since ever since. I want to say it is starter related as the noise sounds like a rapid tapping that slows and immediately stops as if the starting gear that engaged the flywheel is slowing to a stop once disengaged.
View 5 Replies
