Accent LC (2000-05) :: Sudden Stall Without Warning / Won't Turn Over - Code P0340 And P0134
May 12, 2013
2005 Hyundai Accent stalled on freeway today. It was running fine and suddenly stalled without warning. I tried to restart but the engine doesn't turnover just makes a electrical "weeee" sound. Battery works and lights work. Code reader gave P0340 and P0134 codes.
P0340 Camshaft position sensor "A" circuit malfunction bank 1 single sensor
probable causes:
-Open of short circuit condition
-poor electrical connection
-Faulty CMP sensor
-Engine Mechanical fault
P0134-Heated O2 sensor bank 1 sensor 1 (H02S11) circuit no activity detected
Probable cause:
-Poor electrical connection
-Rich or lean Air/Fuel ratio
-Engine mechanical condition
-Faulty H02S11 (Bank 1 sensor 1)
I'd like to fix it myself; where should I start?
View 3 Replies
Advertisement
I have a 2002 hyundai accent gl, 1.6l dohc engine. The issue is in the cold weather, the car will turn over, and then buck and stall right out. After a while, she will finally catch and idle really rough, until the car warms up, and the temp gauge goes to halfway, and then it all goes away, and the car runs perfectly fine. Its only in the winter it does it, and when the car is really cold.
I just put a new battery in today, the alternator is newer, fuel pump is newer, new plugs and wires. I am leaning towards the coolant temp sensor gone faulty. I was wondering, where it is located to on the engine so I can change it out.
View 23 Replies
Our 2005 Hyundai Accent GLS refused to start yesterday. It seemed like the engine was struggling to turn over. It took about 10 minutes and then the engine FINALLY started. CEL came on. We drove about 1 mile and back, and the engine seemed fine. We even turned the car off, and turned it back on with no issues.
We took it into the shop but it's been about a day and they can't replicate the issue.
FYI, the CEL code is "P2096" (Post Catalytic Fuel Trim Bank 1 System Too Lean). This has prompted the garage to look at the fuel pressure system.
Historical Issues:
1. Last year, we found out that the car had minor issues trying to start up. Specifically, it takes an extra second or two for the fuel to be injected into the engine upon start-up.
We would mitigate this by: sticking the key in > turning the key halfway > wait about 2 seconds > then turn the key all the way.
I wonder if this starter ignition or fuel injector is wearing out.
2. About 2 months ago, the car started to struggle when it came to changing gears -- especially on the highway when trying to reach the 4th gear. The car would also randomly jerk regardless if we were decelerating, accelerating or maintaining speed.
Around that same time, the car struggled to go uphill (especially on a very steep highway hill that's near our house). The CEL would flash and we were constantly nervous that the car would simply die and roll backwards.
It seemed like a transmission issue but the garage we took it to replaced the coils, wires, plugs, and vacuumed out excess carbon dioxide buildup. Since doing so, the car was running perfectly.
View 4 Replies
2004 Honda Civic with 166000 miles.
--Had Check Engine light on for a couple days and code reader said P0135. Parts guy said this means "Bank 1", my Haynes book calls this code for " Primary Sensor 1" Is this the same as "Upstream"?
--Replaced O2 sensor (Denso 192400-1160 05F12) myself with a new one (Bosch 15710). Fit perfectly, plugged right in.
--Check engine light goes off for about 5 minutes but comes back on with code P0134.
What should I do now? I replaced the sensor closer to the engine before the catalytic converter. Very easy to reach from the top. I rented the correct tools and did not damage or force anything. Is there a second O2 sensor after the cat that is not so easy to reach? Was that the one I needed to replace? Did I misunderstand the meaning of "upstream" or "Bank 1"?
View 12 Replies
Well zipping along the highway tonight, sitting on 100KM/h, and all of a sudden the engine loses all power. As luck would have it a fuel station was just closing (the only one for half an hour either side) and kept the lights on so I could have a look. The starter is nice and lively, and the engine is trying to fire, but just wouldn't. I asked a mate of mine in town to come out and give me a hand troubleshooting.
As it turns out, when the ignition switch is set to the "ON" position, normally the fuel pump primes the lines. It's only doing it intermittently for some strange reason, and not making it past the fuel filter (despite the filter being new). The temporary buzzing in the engine bay when the car is switched off is gone now too.
Now my question is - does this sound like fuel pump? I'm only used to the older fuel pumps in carburetor vehicles, not these fingle fangle electric things!
View 4 Replies
2000 jetta 1.8t ... Yesterday driving home from work (1.5 hr drive and it was 25+ degrees) my car died on the highway just before I made it home. Just lost power all of a sudden with no warning signs before and no overheating. No lights came on I just felt sudden loss of power and pulled over and turned the ignition off and it wouldn't start again. Just makes a high pitched whining noise and won't crank over. I just found out the other day that both O2 sensors need replacing but I can't see that being the reason.
View 5 Replies
I have a 2002 accent, 1.5L 16v. So the story is the other day my fiance was driving home and about 200m after she took off, the front wheels chirped all of a sudden and then she noticed it was lacking power. It was still moving along ok and got her home, however it didn't have enough grunt to even get up our steep driveway. I went outside and turned the car off and on again, then all of a sudden the problem was gone and the car drove fine up our driveway. To me this sounded like a sensor or computer issue, although no warning lights are coming up on the dash at all. The next day when driving it, it gradually lost more and more power as the drive went on, but didn't seem as bad as the first day. And again turning the engine off and on again seems to resolve the problem short term. My only thoughts are possibly the maf sensor or the trp sensor. But I'm not really sure.
View 2 Replies
My 2004 Accent transmission with 145k miles all of a sudden started slipping while driving. It would be fine until i needed to slow down and then step on the gas again. It wouldn't catch right and it would slip. At first the pull of the slip was very slight and at times now it is very rough. My check engine light does not turn on when it slips slightly, but only when it has a really rough slip will it turn on. I had it checked at the local advance auto parts and i was told it has a 4th gear ratio that is off. The only thing that confuses me is that when i turn the car off and on it resets and works fine, that is until it slips again. If i drive carefully it usually wont slip. Could it be an electrical problem?? I changed my speed sensor when my car had about 132k miles because it went out, i replaced my ignition coils, new spark plugs/wires, tranny oil change, and filter change.
View 2 Replies
My 2001 Accent doesn't give me any power when its cold in fact when I try starting it when its cold, the car will start and then after 1-2 min would violently (may be that's a little too strong a word to describe it) shake and then stall. This happens about 1-2 times and then the car finally starts.
If I drive my car uphill (not a very big), after heating it up, car would just start moving along slowly (or stall) even on the first gear and full gas. And sometimes while driving the car loses all power. It just trudges along no matter how much gas I press,
I no nothing about cars, so I am not sure if I conveyed my problem correctly. I just hope that the problem is fixable and wont cost me my entire salary to fix.
P.S: I always thought that the problem was me and that I couldn't drive a manual. Today a friend of the mine, who has been driving manual for 20 years also had the same trouble.
View 4 Replies
I have an Acura 2000 TL. My car all of a sudden stopped starting. I called AAA and the tow truck driver did some repair like thing. The car started after this. He told me, there was a problem with the remote starter or security alarm issue. After that the car starts but the immobilizer light is completely off. It gives P1607 OBDII code. When I looked under the dash, I saw a black button and pressed on it. It gave some clicks and nothing happened. I pressed on it and turn the ignition switch on and off a couple of times and nothing happened. I pushed on the button while pressing on the brake peddle and released within 2 seconds etc. The car has a Code Alarm remote start with two button fob and it was disabled. I don't know whether the AAA driver enabled it causing the immobilizer bypass to actuate to have the P1607 code. The car starts ! What can I do to get the Code Alarm remote start to disable it?
View 8 Replies
My wife drove the car to work, and it ran good. She got a check engine light, but it was not on when I got home from work. I started the car and it idled fine for a couple of minutes and then it stalled. I check the codes and there was nothing locked in. There was a pending coding P0321. I am not sure what a pending code is, but I assume not enough to trigger the check engine light.
After work each night this week I tried troubleshooting but I have not gotten anything accomplished. Each night the car would start fine but if I turned it off it would not start until many tries if at all. It turns over strong but won't start. I drove it around the neighborhood today and it stalled and wouldn't restart.
The fuel pump primes. When the car won't start the fuel pump relay clicks constantly. Is this normal? I replaced the fuel filter because it has been 50k miles. Is the crank shaft sensor the problem? I hate to throw money at parts that aren't the problem when I can't get a code to trip the check engine light.
View 4 Replies
I have a '00 RAV4 I bought from my Mother. It was having loss of engine power and it would stall while driving and then turn off while driving. The car was taken to 4 mechanics, non could figure it out changed the sensor air fuel ....worked then did it again sent to the Toyota dealer changed the same part ....the problem seemed to be fixed....I've had for a couple of weeks and the problem came back...what I notice was a low idle, loss of power....then the car started stalling while driving, the rpm idle dropped to 0 and car shut down took to mechanic said the throttle body was dirty . They cleaned it they said that it fixed the problem ....2 weeks later it happens again to 2x .....I don't know what to do ...
View 1 Replies
P0300, P0301, P0303, P0305, P0032, P0052, All this happened after the car was being driven at 74 mph all of a sudden it started to stall and had to pull over to unfortunately get a wrecker back home, no previous issues, original owner 2003 camry le v6 now has 230k. I changed the fuel pump/filter, changed the coils, changed the plugs, removed the firewall bank 1 catalytic, looks good still, I do have a video of the car as soon as it got home off the wrecker running rough...
View 2 Replies
I bought a 2006 Prius. A few days ago the car was driving along just fine when the red triangle appeared together with the 'problem' message followed by the red oil warning displaying in the top left corner of the screen. A few seconds later, the yellow engine light lit up and I drove the remaining mile or so back home (very slowly and carefully). I should point out that the car didn't drive any differently after these warnings appeared and I haven't noticed any strange sounds or anything like that.
I've been out to the car on a few occasions since. It goes into ready mode just fine and drives perfectly in EV mode. The triangle and oil warning reappear shortly after the engine cuts in every time it's started. The hybrid battery charges and discharges on the display when it's left at idle as normal. A friend of mine has a cheap and cheerful diagnostic machine that he brought over and that pulled the P0340 code which relates to the camshaft position sensor. That sensor has been replaced for a brand new one and the fault codes cleared but the code is still showing.
View 9 Replies
Bought this car new and really haven't had any major issues until the last month. It's a 2003, six-speed, inline 4, 1.8L engine. When I came to a stop, the engine just died and would not restart until I let it "rest" for a couple of minutes. It restarted and ran fine. This same thing happened again a week or so later.
Then, just yesterday, I was doing about 65 on the interstate and the engine died, tach dropped to 0, but I didn't lose power steering or brakes. I was coasting for a few seconds and the engine came back. When I slowed down to pull into a parking garage, it died but I was coasting enough to pop the clutch and it restarted for a moment allowing me to almost get into a parking stall. As I slowed to get into the stall it died completely and had to be pushed into the stall.
I left it there for a few hours. When I got back, it started and ran fine. I feel this is just the beginning of some problem with the electronic control module/unit.
View 3 Replies
Ok had a check engine light. It directed me to replace the IAT sensor.. After some research I found it was integrated into the MAP sensor. Purchased a new sensor and replaced. Drive about 15 miles CEL throws another code. P0106 (sensor i just replaced) faulty Map sensor.
Followed procedure to replace sensor.. unhook battery cable reset ecm. After reset engine is hard to start. Followed by RPM changes (assuming its the ECM re-adjusting). Then CEL flashes 5-6 times and goes out, Drive 15 miles. Map sensor code reappears. (note i only purchased one sensor But repeated install 2 times).
My thought is against wiring. since the codes refer to different signal wires one for IAT one for MAP sensor. Faulty replacement sensor?
2002 Accent 1.6L
View 3 Replies
I have a 2001 accent 5-spd. I was on my way to work and I was making a u-turn when the car suddenly died. I tried to start it back up but it didn't even sound like it was turning over. I tried to bump start it or do a rolling start and nothing. I had to go to work. When I returned to it 8 hours later I again tried to start it and nothing. When I turn the key it makes a "whirring" or "humming" noise, kind of like a vacuum noise. When I had someone else try to turn it, I noticed the belt was turning, but the engine wouldn't crank or make any attempt to turn over. Just the belt was spinning and no engine crank. What could this be?? Could it be the crank position sensor?
View 1 Replies
My CEL is on and according to Auto Zones code checker read a P0340 on my 2002 KIA Sedona with 160400 miles. It said Camshaft position sensor A circuit malfunction 1 or single sensor.
So what should I do now? Van is running as smooth as ever so not sure what I should do.
View 11 Replies
I have a hyundai accent 2005 vehicle and there is no Low warning fuel indicator in the vehicle. My entire fuel tank ran dry still there was no low fuel warning light. According to my mechanic there is no low fuel indicator installed in the fuel pump
My VIN number is KMHCG41GR5U633054
View 8 Replies
My mother has a 1999 Camry 4cyl. that has code P0340. She says that she was driving down the road and felt like a misfire, saw the MIL turn on. When she let off the gas, she said the car stalled. It is a crank no start issue now. I was able to pull the code, but really am not familiar with Toyotas in General. I am mechanically inclined but do not have access to media such as All Data or a Service manual. Do this is most likely the sensor itself or more of an ECU issue?
View 10 Replies
2002 Santa Fe 2.4L Automatic. Driving on the freeway when it lost power. Couldn't go over 65 even with the accelerator all the way down, even slower on uphill climbs. The engine wouldn't rev higher than around 3000rpms.
I figured it sounded like a loss of power due to weak fuel pump. I replaced it as well as the fuel filter, and verified it was pumping. Put the car together, and still the same loss of power. Drove home and parked it, but next morning it won't run at all. It cranks all day long but doesn't fire.
So far, I have made the following repairs and checks:
-Verified catalytic converter was clear and not plugged
-Verified fuel pressure
-Checked spark plugs - all are good and gaped properly
-Replaced crank position sensor (With the code, I thought this would solve it)
-Verified timing belt and cam belt in time - both have also been changed recently
-Checked all relays and fuses
-Battery and alternator are good - both are new
I still have a crank no start issue, and I'm going crazy taking things apart and putting them back together only to have this car not fire.
View 13 Replies
