Accent LC (2000-05) :: Shuts Off When Idling Warm
Dec 19, 2013
My accent had been sitting neglected for a few years. I decided as a side project I would get it in working order before winter and do more to it next spring. The car had a rough idle when started but I had ran it nearly all day a few months ago.
Last week I changed spark plugs and a few other minor things. The undercarriage was wire wheeled and coated with POR 15. This weekend I added gas (with gas cans, car is off road currently) and added techron fuel treatment. The car took two tries to start (always two) so I changed the fuel filter and that problem went away. However, I noticed that when the car idles it begins stalling when it reaches temperature. Thermostat says car is not overheating.
After 15 or so minutes of idling the car just cuts out and SOMETIMES will start but usually it just cranks and cranks. If I wait a bit it will start up again but will die more quickly and this will keep happening until I let it cool. I am also noticing a fairly loud clicking sound from behind fuel injectors. Not the injectors themselves but somewhere behind the fuel injector rail. I am unsure if this had been going on previously or if it is a symptom of the stalling problem.
I cleaned throttle body, IAC, crank and cam sensors though no error codes to speak of. Rough idle takes a few minutes as at first the engine is smooth.
View 8 Replies
Advertisement
I know, sounds like blown head gasket. However oil looks fine, no coolant leaking and coolant looks fine. It also does not overheat (that I can see, it dies first). This all started a few weeks ago. I changed spark plugs, oil and undercoated the car with primer. I did get some paint on the radiator. I also put techron in the fuel tank and changed fuel filter. The car ran fine before, now here is what is happening step for step.
Car starts fine, idle is a bit rough (it was before too) but nothing drastic. I rev car at 2500 RPM until it is warm. The thermostat stays in the middle yet I begin to see a good amount of white smoke coming from the exhaust. If I take foot off the accelerator the car will shut off at this point. If the car is not warm yet, it won't shut off. When it does shut off, I cannot restart it even with gas pedal down. It just cranks and cranks. When I let it cool down it starts up fine and the same thing occurs. I cannot tell if the radiator fans are turning on as the car dies before they turn on (it's cool outside). The thermostat never indicates overheating.
The entire radiator is smoking white (not from cap) but I assume that is from my paint overspray burning off. Could this be getting sucked in and stalling the car out when the car warms up enough to start burning off the paint? Could I have painted something inappropriate? What could this be? I know a decent amount about cars.
If I let the car warm up just by idling it will run until it gets warm then it stalls and again, won't start until it cools. It seems to keep running if I keep RPMS up but right when I take foot off accelerator when warm it shuts off.
View 19 Replies
Car starts and run find when cold. Shut off when warm up , will not restart? Could this be a crank sensor problem?
2004 accent GS with 150,000
View 6 Replies
I have a 2000 Hyundai accent. Bought the car used at a lien sale over 3 years ago, with about 120k miles on it... it now has over 197k miles on it. I have changed the oil and filter religiously since I bought it, using Castrol GTX High mileage 5w30 synthetic motor oil. I have also (in the last year) replaced the plugs with platinum plugs, the plug wires, and the air filter. A the car has always made a tapping sound when idling since I bought it, but recently (in the last week), it makes little shoemaker sounds when I accelerate. I used to associate this with detonation and adjust timing (back in the day when you could put a timing light on a car and turn the distributor to set timing). Since timing is now controlled by the computer in the car, am I right in assuming that I need to replace the timing belt?
View 4 Replies
What happened was, the car was not starting (its a manual, so I can push start). I replaced battery but accidentally put it in with the neg connected to pos post and pos. connected to negative.
The car was off when i did it so as far as i know I only blew a couple fuses. So I replaced the fuses and now the car is idling really high. So I cleaned the throttle body, still idling high.
Now, the car wont start unless pushed and I have no ac/heat (the fan has no power).
I have checked all of the fuses and they are fine. I have also tested the Throttle Position Sensor, it is fine.
Could it be the diodes, relays???
View 3 Replies
I have a 2000 Accent that wont shift past third gear until the car is warm. The car has 140k miles. When I turn on the car and pull onto the high way it sticks in 3rd. I then have to slow down and drive through a small town. When I get on the other side of the small town and get back up to speed it will shift. Over drive is on.
View 4 Replies
My friend's Accent LC 1.3L won't start from time to time. This never happens on cold start, this is always the situation after warm engine stops and needs to be run again after 5-15 minutes. When you try to turn on the car then, starter is rolling the engine but nothing happens (Yellow key light on dashboard is on, so there is no problem with a key code). Then he wait for a few minutes and car starts like it nothing happens. I suspect the crankshaft sensor.
View 2 Replies
This is what my car is doing after it warms up. It will do it then stop, then do it again and so on. I am pretty sure when the motor is under load it runs a little rough but is hard to tell. The car has 178,000 miles on it. timing belt was done at 113,000. I just replace the plugs and wires changed the oil and the air filter 1,000 miles ago. and it will still do it. I am at a loss as to why it keeps doing this. I have tried injector cleaner, sea foam and engine restore. What would cause this? The check engine light is not on. i replaced the crankshaft positioning sensor about 40,000 miles ago.
Its a 2003 hatch with the 1.6 5 speed .....
View 8 Replies
2000 Hyundai Accent GS, 1.5l, 4cyl SOHC...
I have a slight issue. A few weeks ago, I put some "STP" style fuel injector cleaner into my gas tank. Either A) It cleaned everything really well and clogged my injectors, or it turned into gunk and possibly clogged something else up.
Ever since that day, my issue is that the car "stutters" very slightly. When idling, it'll "hiccup." When I'm doing normal driving, 55-60mph at 2k RPM, It'll almost feel like a transmission slip.
I've went and replaced my Fuel pump, filter, and now I've done half a can of seafoam through the brake line power booster (vaccuum) straight into the engine, and the other half into my oil for further cleaning. I also applied Seafoam Deep Creep into my throttle body, just for further maintenance.
Ever since then, everything has been running noticeably better, and I've had a huge increase in gas mileage, but there's still a slight hiccup that occurs during idle and driving.
I change the oil /filter, plugs, wires, air filter on a regular basis.
I also had to change the MAF at one point in time, as it died and the car wouldn't start at all.
Next thing I'm thinking about doing is changing the plugs / wires one more time (it's been about 5 months since my last change) just to see if I bought a faulty plug.
The car was put on a computer and the only error code that came up was one about my check engine light being out.
View 3 Replies
I just bought this transmission from a reliable parts dealer. Should have about 50k miles on it. Looked really clean when I got it.
The guys who put in the tranny cracked a speed sensor, so I bought a new one and put that in. I dried off the sensors and screwed them into their spot on the tranny after removing the intake filter that was in the way.
Even with the new speed sensor the car is still doing the following:
1) Does not go into reverse until I've gone into drive for a couple seconds, pulling forward. Reverse does not work. However, when I unplug the speed sensor reverse works right away, but we still experience the following...
2) car goes from first to second gear to third gear smoothly, as it should. Seems really smooth like a car should shift! However... it won't go past 3rd gear and then it won't downshift! So, even after stopping and idling, I can't leave 3rd gear.
3) When I turn the car off, then turn it right back on, I can go through first, second, third gear again then... it stays in 3rd gear.
Another issue that has come to my attention since I got the car back, is the steering wheel shakes pretty hard while idling with no gas. While driving it seems smooth -- idling again it shakes heavily. what could they have damaged while putting in the tranny to cause this shaking?
So far as the funny tranny stuck in 3rd gear, it seems to me like it's a computer issue? But, what could be the cause? What tests can I do to determine the cause of this problem besides the ones I've run so far?
View 17 Replies
This problem has plagued me for a while(since last year). When I start the car in the morning, there's a brief period when the power steering is totally gone. When the car is thoroughly warmed up(after 2 minutes of driving), the power steering is back and there will be no problem. Wondering what could that be. The power steering fluid level is normal.
View 5 Replies
Owning a Hyundai. I have a problem and it seems to be pretty common but haven't gotten anywhere with it yet. Last week my 2004 accent 1.6 manual transmission started running rough. It was idling higher than normal and while driving would not go past a certain rpm (about 2500 if I had to guess,no tach). On the way home from work it was running this way and then started badly misfiring and shut off, when attempted to restart it would not. I pulled the codes with a scanner and got p2400, p0562, and p0121. I charged the battery and replaced the throttle position sensor, still won't start. I can hear the fuel pump kicking on when I turn on the ignition. Also found the ecu 1 fuse blown, replaced it and continued to attempt to start with no luck, fuse was blown again. Like I said I haven't owned the car long and I don't know much about it. I am not sure where to go from here and I don't know how all these symptoms are tied together.
View 42 Replies
I am Having problems with my AC. In order to get it working i have turn the fan on- off two or three times to kick the compressor on. then when idileing it will sometimes shut down?
View 3 Replies
2005 Saab 9-5 ARC 2.3T67,000 Miles
Noticed a problem 2 weeks ago with my little Swedish meatball while at a red light on the way home. While idling, the car just shut off. I'm assuming it was a stall, but the car did not sputter and it was idling at around 900-1k RPMs but then just cut out. I put the car in park, and it started right up without issue and I drove the rest of the way home with it running fine. A couple days later, the same exact thing happened.
I took it in to my local Saab shop for a radiator hose replacement and an oil change. I told him about the stall/cut out problem, so he hooked up the Tech II but could not find any trouble codes. So he did a software update to the computer and told me to monitor it and call him if it happens again.
After getting my car back, it ran fine for a few days. I tried to get it to stall again by just letting it run in idle for 10-15 minutes but it wouldn't cut out. One night, I went to the gym for about an hour and came out and my car started right up and I drove about 5 minutes and came to a light. Car cut out again. However this time, it did not start up again. The engine would crank, the computer would go through the checks and give me the Check OK but it just wouldn't turn over. I tried to start it 5 or 6 times but no luck. I got out and pushed it to the side of the road. After about 2 minutes for sitting there, I tried it again and it turned over. Started right up like nothing ever happened.
The car drove again fine for a few days and then yesterday it cut out again. Same thing. Car would crank but not turn over. I let it sit there for 2 minutes (as traffic was going around me at a red light ) and then tried it again. The engine turned over but it did not start up fine. It definitely stuttered as it was trying to start and I had to give it some gas to get it running smoothly.
Couple of observations: This has only happened while idling (in Park or Drive)This has only happened when the car was warm. I've never had an issue starting in the morning or before the car warms upThis appears to only occur when it has been warm outside. (We've had a few days in the 60s here in PA)The Check Engine Light has never come on. So no trouble codes have ever been logged.
I've been searching the forums and most people seem to recommend replacing the Crank Position Sensor (my mechanic wants to do this as well). However from what I understand, if it was the CPS the car wouldn't stutter like it did when starting after a stall and wouldn't the CPS cut off the engine while driving as well?
View 3 Replies
I have a 2012 Prius. It has twice shut down spontaneously when idling while in traffic. I have explained this, the Service Advisor said he had never heard of it. My question is: why is this happening? The car has been properly serviced. It never happened with my 2006 Prius.
View 12 Replies
Yesterday, my truck began to shut off abruptly. Under every condition, from idling to slow running (30mph), and 70 mph, to load and no load. Wait 1 minute and it would start and run for 1 minute 15 seconds. If the batteries were disconnected, the truck would run for 13 minutes before shutting off. Have replaced the fuel filters. Still does it, but runs for between 10 and 20 minutes before shutting off.
Am seeing only two errors codes. P1000, and P0603. I was 40 miles into the Ville Vidal, when this started, and 150 miles from home. To get home, I disconnected the batteries too many times to count, and bled the HFCM numerous times. Am also seeing the moisture in fuel icon on teh dash light up when it quits, but so far as I can tell there is no moisture in the separate.
2003 F450 6.0, automatic. 150K miles.
View 14 Replies
I am having a problem with the heater on my 98 2.7 Intrepid. Will not blow hot air when idling (just warm). After several minutes of driving with heat on air temp goes from hot to warm. It might just be me, but it seems like the air flow is cooler coming out of the defrost vents than from the dash/floor vents. Thermostat has been replaced (proper operation verified before installing). Had to replace gooseneck and heater coil supply tubing due to a leaking bleed valve. There appears to be NO air in the system.
Heater core was backflushed, there appears to be no restriction. Hose temp on exit line is approx. 15 deg. cooler than supply line when fan is running. Blend door actuator was replaced last spring (motor shorted). When temp control is moved from hot to cold temp changes drastically and door can be heard moving. On-board ATC diagnostics indicate all is good. Engine is running at normal operating temperature, not overheating or running cold. Is there a cabin filter or inlet supply for the air that could possibly be obstructed? Air flow seems adequate, not restricted. AC works fine.
View 4 Replies
I can't believe what I'm saying as I always say to start driving (slowly) to warm up the engine. Besides, who has the time?
But, this AM, I was stopped as soon as I exited my driveway as big garbage trucks blocked my cul-de-sac street. The engine went through the warm up cycle as I waited stopped and later, I went through my usual commute.
The thing is the commute ended at 67 MPG (indicated). I usually get "only" 60 MPG on the very same route, unless the engine is prewarmed before driving and I get exactly 67 MPG. I always clear MPG trip counter before driving on a daily bases.
View 19 Replies
Having problems with the A/C on F150 2006 or newer. It blows warm air while idling. I have taken mine to 2 different dealerships had Ford engineers down and no one can seem to find the problem. I love Ford vehicles but I can't handle this in the these hot summers.
View 10 Replies
I have a 95 4.0 EFI inside of my 83 Ranger. Once the motor warms up, it starts to have an idle issue. I have to press the gas, in order for it not to cut off. Here is a video I posted a while back. A person suggested that it could be the MAF needed to be cleaned. I did that, and it did not work.
View 9 Replies
My '04 Ranger has over 240k on the odometer. Runs great and has never given me any issues. Everything checks out OK - all the fluids, filters, and whatnot are in good shape. No CEL or any other indication that anything is wrong (except for maybe the IAC valve and clutch slave.)
I've noticed, though, that when I fire it up in the mornings to let it warm up while I scrape the ice and snow off the windows, the heat/defrost will not blow warm air. It doesn't matter how long I let it sit, it will only blow ambient air through the ducts.
When I get going down the road, however, the heat kicks in, after a bit, and works very well!
I've not found anything that would indicate an issue with the blend door or any other component and this is the first vehicle I've had that did this.
Is it normal for a 4.0 SOHC Ranger to do this? Or is there something I'm missing?... It's not really that big of a deal, but I do find it a bit odd that it would do this.
I mentioned the IAC above - I think it's "sticking" every once in a while and, when it does, I'll hear a loud "thump" right before it idles down to around 1k rpm. I can't see how this would affect the heat, though...
View 14 Replies
