The steering on our 02 Accent has been becoming more and more difficult. The belt on the AC compressor snapped off recently. Could this missing belt be causing a problem with the power steering belt? The power steering belt is now making a squeaking noise.
View 3 RepliesMy car is a 2002 Accent. So last weekend I replaced my timing belt and my 3 other belts. Before I did this the belts were not squeaking and I was not having any issues with my power steering. I started my car up and the power steering pump was making lots of noise, the power steering reservoir was still full. I was told it's probably the power steering pump and that I would need a new one. So I got a new one, put it on and still the same thing. I looked online and saw that it may be an air bubble in the line so I removed the cap on the reservoir and, with the car turned off and the front wheels off the ground, cranked the wheels lock to lock about 20 times. I started the car and it still makes noise. This morning the power steering felt like it was lagging as I was backing out of my driveway and the squeaking happens when I am idling and gets louder and worse up to about 2000 rpm then stops, which it has been doing since I replaced the belts. I am not sure what else to do, did I mess up the new pump by driving and not bleeding the air out?
View 2 RepliesI purchased a new 2000 mazda b4000 2 weeks ago and the belt was squeaking and I knew I had to change the water pump so I replaced it and the squeaking didn't went away... I thought maybe my idler pulley bearing was worn out cause I could see it wobble back and fourth when the engine was running... Replaced it, still squeaking! Change my belt still squeaking! look further turns out my power steering pulley wobbles slightly. I'm thinking about trying a gator back belt and see if the squeaking goes away. Could it be dangerous to run the truck as it with a slight misalignment in the power steering pulley? or it'll be a must replacement asap?
View 3 RepliesWhere to find a nice, simple step by step instructional for tightening power steering belts for a 2003 hyundai accent?
View 4 RepliesAwful belt noise that erupts during cold starts. I realize that this usually means a replaced belt. I want to know how to go along diagnosing which belt and then how to replace it. Here's the symptoms:
1. Awful belt screech when turned on, goes away within 20 seconds
2. Belt noise comes back when turning the wheel to back out of a right driveway
3. The STEERING WHEEL feels like it has no power steering WHILE the screeching is happening.
4. The headlights (when on) dim for about 3 seconds
5. All these symptoms happen when the temperature is below freezing and it's a cold start.
How is the belt screeching connected to the steering wheel being tough I turn?
My '02 Hyundai accent's power steering pulley makes noise when the car is turned on all the way. That noise doesn't go away until I shut off the car. It is not the same noise as a belt slipping as I have that problem before and had fixed it by tightening the alternator adjuster bolt.
When I spray a little bit of WD-40 on the P/S pulley bolt(bolt and split washer) the noise goes away. However, it comes back the next day, since I am guessing the WD-40 has been dried away. So, should I replace the pulley to fix this issue or is it something else?
Pic of Bolt (Its yellow and black in the pic) ....
I have a 4 door 2005 Accent with ABS. I mainly drive in the city, and lately I noticed a squeaking noise that sounds like it's coming from the front right side (from inside the car); it is a constant noise. I pulled the brakes off both sides, the pads are fine, the rotors were a little rough (normal). Before I reinstalled everything I took some 80 grit emery cloth and roughed the pads and the rotors with it just in case there was some glazing.
The noise is still there and what concerns me more than the noise is the fact that the longer I drive the car the more gas I seem to need to apply to get the car to move.... not a huge amount but enough. Also, once I stop the car, there is a slight brake smell and the passenger side front tire area (brake) is crazy hot. Long story short; I would like to check to see if I have a stuck piston in the caliper, But I'm not 100% sure how to. Do I pull the pads off, push the piston in , watch how fast it goes in, and then compare it to the drivers' side? Or do I need to pull the caliper apart?
Since it's "auto repair season" in my driveway, I was working on my daughter's car (2001 Accent, 1.6 GSi) and noticed that the air conditioning compressor makes a noise (like a cross between a burble and a shriek) when it cuts out. I'm assuming it's the head unloader and was wondering if it's supposed to make a noise that's quite that loud or if maybe it's getting low on refrigerant - the compressor runs quietly when it's turning and the clutch doesn't make any strange noises.
View 3 RepliesMy engine is making a ticking noise. Louder when I start it and not as intense after it warms up but its still there. I first thought it was one of my pulleys making noise but I brought it to a friend who knows a lot more then I do and he says to check the engine valves. Did some searching online and thinking it might be the valve lash adjuster but not sure.
Anyway whats the best way to go about this? What type of oil should I be using and I also read I should be only buying Hyundai oil filters?
My daughter has bought a 2003 4 door accent and on the way to work she lost most of the brakes. I could not see any fluid leaking and the level was ok. I did try pushing on the brake pedal with my hand and it was making a noise like a clicking? I was thinking it was just the brake light switch but not sure. The place she bought it from put new brakes on it when the driver side was getting really hot. I am thinking maybe air in the system? It sounded like a caliper was sticking when I test drove it but only a couple of times. You would have some brakes but you had to pump the peddle.It is in a parking lot right now but I can work on it unless it is some sort of different? I am going to try to bleed it in a little bit but was thinking I should ask around. I read that the piston could be sticking but can you just rebuild the master cylinder to fix it if that is what it is? I could pull the pedal back a little bit. I only looked at for 4 or 5 minutes kinda dark and no tools with me.
View 10 RepliesI bought a 02 accent base model hb 5 speed 109k miles for a winter car (have a mustang in garage.) It ran good until tonight when the timing belt snapped. I know this because while driving it made some ticking noises and then shut off and when you try to start it the noise that comes indicates no compression so the belt must've snapped and bent the valves.
View 3 RepliesI have a 2001 1.6 DOHC Accent the engine has been making a lot noise coming form just the back of the head it kinda sounds like a diesel. I pulled the valve cover off and turned the engine over by hand. I noticed that cam chain has a good amount of slack in it. Is there a tensioner to take slack out of the chain? If so can I adjust it? If not how do I replace the chain?
View 8 Replies2004 Accent 1.6L
Changed the timing belt and water pump this past weekend. I made sure the timing marks aligned before I put the belts on. They were still aligned after turning the engine by hand and still aligned after taking the car out for a test drive. I did not notice rough idle when I started the engine in the garage nor did I notice a rough idle during the test drive.
A few days later I am now noticing the car will idle roughly when I come to a stop. The idle will get rough enough to gently shake the car. No engine light and no unusual noise from the engine.
I am going to check the timing marks again tonight. I suspect the belt may actually be off by one tooth. I have driven over 100 miles since changing the belt so I don't believe it is off anymore than one tooth or else I presume I'd probably have already broken down or been hearing unusual noises.
Furthermore, I do not seem to have any loss in power. I still have good acceleration and no roughness unless at idle engine speed. I do, however, run rough at higher speeds (75+ mph) on the highway, but this was present before the timing belt change. Unfortunately the car does not have an RPM gauge.
Having said all of this, are there any other possible reasons why I might be idling rough now?
I own hyundai 2000, 1.5L. About 5 days ago the engine started making strange noise that sounds like sewing machine.
I went to my garage and they said that its the hydraulic valve lifters and that I should replace all of them(12 total).
My question is, what can happened if I wont replace them? can I postpone the replacing for a few months or it can cause damage?
By the way, I heard that the noise from hydraulic valve lifters can start due to bad oil, I had 20W50 so I changed today the oil to 15W40(manufacturer recommendation) and the oil filter and still got the noises.
Last week, on our mercury monterey, we found that the level of power steering fluid had dropped and steering was making squeaking noise while turning. Filled up the fluid and it worked. Today when checked again, i am seeing drop in level again. So certainly there is some leak. Can we find it at home? Also is it safe to fill the fluid and drive or should we get it fixed asap?
View 6 RepliesThe timing belt went out at idle while making a turn. I changed the timing belt, but when cranked you have to pump the gas to keep it running and it is really rough running with a smell of gas when you turn it off. On the last run it backfired slightly. There is no knocking or pinging. And have triple checked the timing. Could improper torque on the crankshaft bolt cause this or failed ignition coils?
View 21 Repliesmy P/S is making whining weird noises i checked the reservoir and there it is low fluid. question is there a nipple somewhere that i can bleed the air i'm not sure if i am right on this one but i have a feeling that when i ran low on fluid i created an aeration in my pump,reservoir?
View 2 Replies2002 Accent GS, automatic 1.6L engine ... Have a leak in the Power Steering system and I was wondering if it was safe to take the Power steering pump belt off just to get to my mechanic (who is about 18 miles (27 Km) away). I would rather not get towed, but I don't want to do any damage either. I am not all that mechanically capable but think I can get the belt off myself.
View 4 RepliesI have a 2002 Accent 1.6L and when I turn the wheels all the way too the right or all the way to the left the pulley stops spinning. Could this be that the pump is going bad or something else?
View 2 RepliesI just recently had a new pressure hose (had a leak) replaced on the power steering pump but there is a slight squeaking noise when I turn the wheel. the mechanic says it'll go away after a week or so because of the new fluid that was put in? Is this correct?
View 4 RepliesI have a 2001 accent 5-spd. I was on my way to work and I was making a u-turn when the car suddenly died. I tried to start it back up but it didn't even sound like it was turning over. I tried to bump start it or do a rolling start and nothing. I had to go to work. When I returned to it 8 hours later I again tried to start it and nothing. When I turn the key it makes a "whirring" or "humming" noise, kind of like a vacuum noise. When I had someone else try to turn it, I noticed the belt was turning, but the engine wouldn't crank or make any attempt to turn over. Just the belt was spinning and no engine crank. What could this be?? Could it be the crank position sensor?
View 1 Replies