Accent LC (2000-05) :: Power Loss / CEL Blinking (Misfire)
May 14, 2015
So, I have a 2000 Hyundai Accent that has had the CEL light on ever since I have owned it (about 7 months). I was told it was the O2 sensor and did not have it scanned. Occasionally, it would lose power and the CEL would blink. After I would take my foot off of the pedal and baby it for a sec it would usually go solid again and drive okay. About 2 weeks ago it started blinking constantly and it sputters and drives like sh*t. Now, I know that I should take it to Autozone or someplace so that they can tell me which cylinder is misfiring and all, but it is really sketchy to drive. I put NGK spark plugs in it today with no change. I ordered plug wires and a coil pack to see if that straightens out the problem. If it doesn't then I am going to lean towards intake gasket or perhaps a missing or bad o-ring at an injector. So, does this sound like a reasonable plan of attack to get rid of the blinking CEL (misfire) and restore my Accent back to all of its craptastic glory?
View 2 Replies
Advertisement
Well zipping along the highway tonight, sitting on 100KM/h, and all of a sudden the engine loses all power. As luck would have it a fuel station was just closing (the only one for half an hour either side) and kept the lights on so I could have a look. The starter is nice and lively, and the engine is trying to fire, but just wouldn't. I asked a mate of mine in town to come out and give me a hand troubleshooting.
As it turns out, when the ignition switch is set to the "ON" position, normally the fuel pump primes the lines. It's only doing it intermittently for some strange reason, and not making it past the fuel filter (despite the filter being new). The temporary buzzing in the engine bay when the car is switched off is gone now too.
Now my question is - does this sound like fuel pump? I'm only used to the older fuel pumps in carburetor vehicles, not these fingle fangle electric things!
View 4 Replies
I have a 00 Accent with 132k miles, I replaced the motor a year ago with a correct 2000 Hyundai 1.5 with 50k miles. I replaced everything that I could at the time, timing belt , starter, water pump, and clutch. It has been running fantastic getting 40 miles per gallon with zero problems , However in the last week I have noticed a rough idle that seems to miss with a vibration that it didn't have before. I have a noticeable loss of power and torque. My miles per gallon has also dropped to about 25 mpg. My check engine light is not on. I will check the plugs and change the air filter today but I would like to know what else could be causing the problem as I am not really sure what to check.
View 9 Replies
I have a 2002 accent, 1.5L 16v. So the story is the other day my fiance was driving home and about 200m after she took off, the front wheels chirped all of a sudden and then she noticed it was lacking power. It was still moving along ok and got her home, however it didn't have enough grunt to even get up our steep driveway. I went outside and turned the car off and on again, then all of a sudden the problem was gone and the car drove fine up our driveway. To me this sounded like a sensor or computer issue, although no warning lights are coming up on the dash at all. The next day when driving it, it gradually lost more and more power as the drive went on, but didn't seem as bad as the first day. And again turning the engine off and on again seems to resolve the problem short term. My only thoughts are possibly the maf sensor or the trp sensor. But I'm not really sure.
View 2 Replies
2004 Accent 1.6L
Changed the timing belt and water pump this past weekend. I made sure the timing marks aligned before I put the belts on. They were still aligned after turning the engine by hand and still aligned after taking the car out for a test drive. I did not notice rough idle when I started the engine in the garage nor did I notice a rough idle during the test drive.
A few days later I am now noticing the car will idle roughly when I come to a stop. The idle will get rough enough to gently shake the car. No engine light and no unusual noise from the engine.
I am going to check the timing marks again tonight. I suspect the belt may actually be off by one tooth. I have driven over 100 miles since changing the belt so I don't believe it is off anymore than one tooth or else I presume I'd probably have already broken down or been hearing unusual noises.
Furthermore, I do not seem to have any loss in power. I still have good acceleration and no roughness unless at idle engine speed. I do, however, run rough at higher speeds (75+ mph) on the highway, but this was present before the timing belt change. Unfortunately the car does not have an RPM gauge.
Having said all of this, are there any other possible reasons why I might be idling rough now?
View 4 Replies
I have a 2003 Chevy Malibu, V6, 3.1, auto, 140k miles. Car started out with code 0420 with no noticeable symptoms, but then added code 0303 (miss fire cyl #3) with loud knock (mostly after warmup) and loss of power under load. Now internal loss of coolant (no puddles or external drips). Changed plugs and wires - no change - all plugs looked good with no sign of contamination. Questions - if this is a valve/piston/lifter problem (which would explain the knock, miss-fire and loss of power), why would I get the loss in coolant? If the loss of coolant is fouling plug #3 (which would explain the coolant loss, miss fire and loss of power), could that give me the loud knocking? I don't see how a valve/piston/lifter issue would cause a leak in coolant but I also don't see how a coolant leak into cyl #3 would give me such a loud knock. Do I have two different problems? If it is a leak into cyl #3, is there any way to tell if it is the intake manifold gasket (which leaked before and was replaced five-six years ago and which I could do again if I had to) or a blown head gasket (which I don't think I could fix or afford to get fixed)? Engine will occasionally get hot (but not overheat).
View 7 Replies
2000 Jetta AEG ... An intermittent CEL light turned into a blinking CEL after a few months. Checked codes and it threw a P0303 (misfire on Cyl 3).
Pulled the plugs and found this:
There was oil dripping off of the plug from Cyl 3.
I last changed the plugs in July 2014 and only drove around 10k miles this past year.
When I changed them back then though Cly 3 looked like this:
Before I changed them back then I had an oil cooler gasket fail on the freeway and oil shot everywhere under my hood. Obviously oil is in there and it is causing problems.
I have read online and most of what I have read says that it's likely an issue with the VCG (Valve Cover Gasket) or the PCV (Pressure Control Valve) that is allowing oil to get to that part of the spark plug tube. I've also seen some non VW stuff talking about replacing the spark plug tubes.
Also it does appear that there is a little bit of oil around the threads of the other plugs but nothing getting to the all the way to the tip around the electrode.
I have pulled the plugs, wires and the ignition coil as well ... I'm ready for whatever. I am by no means a mechanic but I am capable of following instructions and doing what is needed. My problem is generally finding out what is needed to be fixed.
View 4 Replies
I have an 05 Accent with about 115,000 miles. It is a GLS automatic.
This morning as I was pulling from a stop light about 30 seconds from my office the car was extremely sluggish. I noticed the CEL light blinking and could hear a knocking sound from the engine. I pulled over and found code P0303, cylinder #3 misfire.
I checked the spark plug cable on the coil side it looks ok. I have not been able to check anything else yet as I am at work.
View 2 Replies
2002 Passat GLS, 1.8T, 98K miles.
Was driving home tonight and nearly didn't make it. A few miles down the road I hit the gas hard going up a hill but the Passat kind of lunged a little and lost a lot of power and the engine emblem starting blinking. Coasted down a hill and it stopped and all was well again. From here on I am going careful up hills and not accelerating too fast.
I drive about 30 miles, 10 miles to go and I have to pull a tall hill. Going up this hill the light starts blinking again and I lose most of my power, engine feels like its not hitting on all cylinders and the turbo must be out. Barely make it home going about 40 mph. My check engine light has been on for quite some time, in fact I have had reset about 6-8 times with replacing sensors, air mass meters, etc. Could this be the timing belt?
View 9 Replies
My car is a Canadian 2002 Accent. I believe it's a GLS, and it has the 1.5L engine.
It has a worsening misfire in the low RPM's, although the RPM range this happens in has been broadening. I can now smell unburnt gas when this happens.
This problem first reared its head around a year ago. I replaced the fuel and air filters without it resolving the problem. I changed the spark plugs - the old ones looked to be in reasonable shape, but suddenly it ran great with the new plugs - for a few months.
The misfire started to creep back in. Since then, I've replaced the upstream O2 sensor and cleaned the MAF sensor. I replaced the throttle position sensor. None of these things solved the problem.
The battery terminals were getting pretty corroded - I hadn't thought this would be related to the issue, but I cleaned them. This did not fully solve the problem, but it did drastically improve it. I bought a new battery the same day - the problem while not gone, seemed to be much more manageable.
About 100km later, the problem has significantly worsened again. I tested voltage across the battery - with the car running, the voltage is ~14.2V. When the fan is on full and my fairly high powered stereo is running, voltage still stays ~14.2V. I'm assuming that should mean that the alternator is good?
Previously, I had tried my ignition coil on my sister's Accent, and it seemed to work fine - but I'm not entirely convinced that the coil is guilt free. I have not done any further testing on the coil, and have not tested the spark plug cables - I'm not sure how to properly test the coil or cables, and don't know where to find the appropriate specs for them should I learn how to test them.
I got the car on the cheap, however, aside from the low (now mid) RPM stutter, the car seems to otherwise be in great shape, and only has 150,000 km on it. Unless it's going to cost an excessive amount, I would like to get this car running right again.
View 4 Replies
Well, coming home from work Friday and my truck turned on the check engine light. I did not notice any loss of power or other driveability issues. When I got home I pulled the DTC's. I got P0264, P0273, P0276, P0279, P0611, and U0306. The first four being low voltages. The Second FICM. And the last cylinder 6 misfire.
I sent a message to Ed at FICM Repair asking if there was anything to check before I pulled the beast. He said no it needed service no matter what at this point. BUT, I needed to test batteries and alternator. So I spent some time today pulling off my FICM.
I went ahead and pulled the EBP sensor and tube off from the exhaust manifold. The manifold end was very clean. BUT, the sensor end had a noticeable restriction. I would guess a 40% restriction. I cleaned the tube and the sensor and put it back on.
Next I moved to the EGR. I pulled it off and it was dirty but not what I would call restricted. The valve moved freely. I cleaned it anyway and blew out the manifold before I reinstalled it.
I have the batteries on a charger right now. Once they each charge for 12 hours each I will let them sit a day or two before I load test them. They are about four years old, AC Delco 60 month 875CCA batteries. I have had problems the last 6-8 months with staring the truck. If she sits for more than 3-4 weeks without being run she turns over slow and won't start. So I have had to jump start her a few times. And before you ask I have done a parasitic check and only have .05amp draw. So maybe the alternator is getting weak.
On that note I pulled the alternator and will get it bench tested this week. While I was there I noticed the top grooved and smooth idler pullies were a little "wobbly" so I yanked them too and will replace. Might as well do the belt while I'm at it. Boy this is going to get expensive real fast.
So, I decided to go ahead and replace the bottom coolant recovery hose and the long hose/pipe heater hose too. Boy it never ends. Oh well. I would rather do it now while I have stuff pulled off and it is easier to get to. Ordered those parts from RockAuto to the tune of 219 dollars. OUCH!!!
I accidentally broke my new engine oil dipstick while I was trying to get to the FICM!!!! CRAP!!!! More money. So......... Is there anything else I might want to look at while I am there?
The truck is 2006 F250 6.0 PSD CC SB 4x4 mid optioned XLT with 108,000+ miles. I have a 4" turbo back exhaust, AFE Cold Air Intake, Blue Spring, Hypertec Power Program 3 on the lowest setting, and an after market intake elbow at the intake manifold and an engine oil bypass filter. Turbo was pulled and de-coked about 18,000 miles back. Otherwise no issues. The 90,000 mile service was done about 10,000 miles ago. She gets regular services.
How about methanol injection? Will that keep the intake clean from the EGR sludge? I'm not thinking about added power, just keeping things cleaner? I plan to do the Atlas 40 when the FICM gets repaired.
View 14 Replies
I have a 2004 Accent Gt with only 43k miles on it and I am getting a cylinder 4 misfire when I refuel. I have replaced the 4 spark plugs. The original code was random multiple and now it is just cylinder 4. I tried to swap 2 spark plugs to see if maybe there was something wrong with the plug but the misfire did not move to another cylinder. I've read about maybe swapping fuel injectors, where I can find directions on how to do that?
View 8 Replies
I have an 02 Accent 1.5L that has a misfire on #3. I have replaced the head gasket, valve cover and gasket, intake gasket, timing belt, yes it was top dead center, MAF, Charcoal canister sensor, MAF, plugs, wires, coil pack, injector #3, and the compression in #3 is 130. What else to check. No other codes.
View 3 Replies
2004 Hyundai Accent has is misfiring, after warming up, only in idle. This only happens after about 30 seconds in idle. Could it not be getting enough gas? This being said I was getting misfire on 3 as well but that would happen all the time and cause the entire car to shake. This problem is now fixed and only #4 is causing me problems.
View 2 Replies
I have a 2000 LC that has a few symptoms - intermittent misfire/running rough at these times it has:
dark smoke
uses 3 times the fuel
loss of power (to normal)
will pick up revs slow without running rough and runs normal at high revs.
dies misses and then picks up revs slowly when accelerator is pushed fast to the floor from idle.
Hyundai mechanics checked computer and it coded change spark plug leads this did not fix the problem, and have no idea.
About 6 months ago the car was doing the intermittent thing when it died and liquid was heard splashing on the ground. I found the main petrol line connecting to the pump had come completely off. After replacing all problems ceased and the car ran perfect with full power etc.
I've checked the fuel lines none appear to be leaking etc.
View 12 Replies
Car threw a multiple cylinder misfire, changed plugs, wires, and then coil packs. Code keeps coming back.
View 12 Replies
I have a 04.5 GLI 1.8t, performance mods include, cone filter on the end of my maf, silicone TIP, Forge splitter, 3in custom tbe and unitronics stage 2
I started noticing this problem on the day I got the car tuned, I hadn't noticed it before hand. I replaced the spark plugs and it worked a little, but it continues to do it.
The problem: When I get on it at WOT under full boost, around 2500 rpms, the car loses all torque, misfires spits and sputters throughout the rpm range until about 5300 rpms then it all of a sudden has torque and pulls great.
I don't have any boost leaks that I know of along with vaccum leaks. There is no flashing cel or misfire code for my coil packs. Can this be a faulty n75 valve? if so what could fix it?
View 24 Replies
I got a 2002 and its giving ma a po301. I know that means a misfire in cylinder 1. I replaced the Coils, Plugs and wires, and now its still there but the check engine light is flashing. What next?????
View 2 Replies
Symptoms:
- Check engine light: misfire on all cylinders, and "lean fuel trim at part throttle".
Started with changing leads and plugs without improvement. Then I found the tank ventilation seemed to be clogged, as there was a massive vacuum when opening the filler cap. Checked the canister and replaced a couple of corroded lines. Also used compressed air to blow through the canister and lines up to the Evap-purge valve. Seemed to be OK afterwards (no vacuum), but still misfires.
Changed the Mass Air flow sensor, and it seems the misfires got better, but instead I have some other issues:
- Hard to start when cold. Starts up fine for a second then sounds like it's getting to much fuel and dies. Possible to keep it running if pumping the pedal or holding it at higher revs.
- Rough idle when warm. (Same as before I changed the MAF and plugs/ leads.)
- Drives and runs ok when out on the road.
- Pulled the cable to the Idle Control Valve without any change in idle...?
- Got flashing engine light and "misfire cylinder 4" when giving full throttle on low revs and seond gear up a steep climb.
What could cause this?
- Temperature sensor?
- O2-sensor?
- Idle control valve?
- Coilpack?
View 26 Replies
THE FREQUENCY: This is a condition that has become progressively worse over the last six months. Initially it occurred once a week and now it is happening almost every day, lasts longer and is more acute.
THE SYMPTOMS: Initially and randomly, while driving at any speed, the car would begin to hesitate as if it might stall but did not- The hesitation was much like a shudder or power loss. At this time the check engine light would blink and stay on for a couple of days. This whole event would last less than a minute and the car would return to normal until the next one.
Now, six months later, it is occurring almost every day. At startup, at low speeds, at stop lights.... A LOT!
WHAT HAS BEEN DONE SO FAR: After frequent and unsuccessful visits to the Volvo Dealer all the plugs, the wires, the cap, and the rotor have been replaced with no luck.
The dealer says the code indicates a misfire on the #3 cylinder.
View 3 Replies
I just bought a 03 accent the same day i bought it the CEL came on got it read and it was cylinder 4 misfire. took it to the garage the dealer i bought it from takes it to he said there was a little water around the boot in that weird little channel area under the cover he said he cleaned it up dried all out then reset the code and it was good, for a little about 2 weeks later it comes on again i get it read and it says cy 4 misfire again but also P0133 (o2 sensor bank 1 sensor 1) and i cannot remember exactly but i think the CEL came on after the exhaust started sounding loud, like it has one of those ricer mufflers on it.
Well I jacked up the car today and looked the only thing i saw was after the first cat right before the braided flex pipe there is this weird "shield" looking piece on the underside of the exhaust pipe dunno if its really supposed to be there or what it is for but from somewhere under that piece i can see exhaust coming out(its cold right now) also the flex piece is kinda blackened like its had exhaust fumes blowing on it for a while. i cant imagine why this would be a normal thing but i have never worked on hyunda before. i am thinking if there is some sort of "leak" there that is why the o2 code is showing. i am stumped, esp on the cy 4 misfire all sparks and wires look good i pulled each wire with it running and it bogs down til i plug it back in.
View 4 Replies
