Accent LC (2000-05) :: P0734 Error Code - Hard To Shift Into Higher Gears
Jun 10, 2012
I inherited this car from my grandmother when she passed. It has low miles, around 40k. Since I paid zero for it, I would like to keep it. Historically I have done all my repairs, but never trans work.
Here are the symptoms. The car has issues shifting into higher gears. I have to punch the gas and then it will switch gears. It then began to do this for reverse, and now now reverse does not work at all.
At first I thought it was a speed sensor problem, but when I took it in to be read, it came up with P0734. It could be electrical (Speed sensor?), low fluid (it's not low), or 4th gear.
Is this transmission worth me fixing or paying to have it repaired, or should I move on?
P.S. If I drop the pan and find shavings, I understand that to point to 4th gear and bearing (also what the computer code read as the issue). Do shavings mean it definitely is 4th/bearing, or could it be another blown part?
View 4 Replies
Advertisement
So I bought a 2000 Hyundai Accent for my 16 year old daughter and the guy sold me a car that has a slipping trans. So I went to the Autozone and had the codes pulled and it was a P0734 code. I replaced the trans fluid and replaced the internal bearing and shim with the 42220LK kit from whatever it takes transmission parts store. Trans still slips. What else or should I just unload it?
View 3 Replies
I own a hyundai accent 2000 GLS, i have recently replaced the ECM wiring and a brand new ignition coil, however the engine still sputters when i try to accelerate in higher gears, my mechanic told me that the engine mounting bushes need replacement. is it one of the causes? the sparks plugs are new, fuel pump is working fine.
View 7 Replies
Recently bought a `01 Accent 5 speed.. First question . How do I tell if its the 1.5 or 1.6 ? That will really point me in a good start. Ha... Ok.. Check engine light is on and I found a paper in the glove box with some of the codes wrong with it.. The one I focused on was telling me the fuel system was to lean . blah blah blah... Dont remember the exact code as I felt that my research was good and I replaced the MAF sensor... Didnt clear the code...
Also it was sputtering quite a bit in all gears mainly at low rpms. I did change the fuel filter , checked plugs and wires etc.. Now I replaced the MAF sensor and it has not solved the problem.. Took it to have it rescanned and have been given codes p1127 and p0136 .. both seem to relate to the Bank 1 sensor 2 O2 sensor. question is I have saw the "upstream" sensor located right below the exhaust manifold but did not see a second sensor?
From what I have gathered sensor 1 does the most work, so I`m curious if these 2 sensors are interchangeable? Could I buy the downstream sensor and if that does not solve my problem , take it out on try it in the upstream sensor? Also do you really feel as though just changing that sensor will "cure" my sputtering issue? the car only has 88k on it and seems to be in good shape otherwise.. I really need this check engine light problem fixed so I can get inspection..
View 3 Replies
What this may be. 2004 Accent Automatic. We just purchased recently for my daughters fist car. Today when leaving the house the car stays in first gear, you can move the shifter through the gears but it wont shift up. Reverse is fine. Checked the oil level in Neutral when hot and it was ok. Hooked up my code reader and there are no Codes. Car only has 85,000 KM on it.
View 5 Replies
I have an 02 accent with 1.6 that has no reverse and throws P0732 and P0734. How to repair?
View 5 Replies
That said my wife bought a 2001 Accent 1.6L Auto while I was overseas and it's been a great car, about 8 days ago it just crapped out. The reverse went out on her so we took it to get the codes read and on the way it went in limp mode, started hard shifting between gears and wouldn't go over 45 she says. Took it in to the stealership today and they said that the trans is shot as well as showing codes for P1527, P0732, and P0734. I know what the two slippage codes are and I can prolly just replace the speed sensors and that will be fixed but I'm not sure about the reverse and P1527.
View 4 Replies
2001 1.5L 5-speed Accent
I did a search on this problem and found several people posted the same P0121 code. Strangely many people wrote that replacing TPS did NOT fix it. The code came back in 30 miles or so. Most of them didn't follow up what finally fixed it and only 2 people did by saying they got the code cleared by fixing/replacing:
1. Leak in the intake manifold, bad plug wires, etc.
2. New Head & ECM.
Is there any known fix for the P0121 on Accent 1.5L other than above?
View 8 Replies
I drive hyundai accent 1.5l sohc.. Recently i was on my bots on turbo project.. The process when smoothly until i suddenly realized that my car was only move on 3rd gear.. then i took off my turbo out afraid of over boosting and straight go for diagnostic.. And error p0755 comes out.. So how to troubleshoot this problem..
View 9 Replies
My 2009 Accent started doing the Hard/Jerky shift problem that I seen discussed in the forums. Had check engine light, scanning showed a code P0717. My question is, which sensor should install?
View 4 Replies
I have a BMW 523i SE AUTO (1997) 2494 Petrol. In auto transmission the gears will shift from 1st to 2nd and 2nd to 3rd but won't shift any higher. In steptronic/manual transmission the gears will shift from 1st to 5th without any problems therefore suggesting that the problem isn't the gearbox itself. Only very occasionally does the shift electronics telltale light appear on the dash, yet the problem with the auto transmission is continuous. A local garage specializing in automatics suggested that it was the gearbox inhibitor. I've today had this changed but the problem still exists.
View 5 Replies
This began as a troubleshooting exercise for a P0442 code (2002 model) indicating a leak in the evap emissions system. Often caused by simple things like a loose/poorly sealing filler cap. Not this time
It's a neat design, tucked away up in the fender well. Even sports a very effective stone guard (plastic shield) which hides all that tubing from view. But the shield also traps all the road salt and mud and packs it into the crevices between the tubes where it stays from one winter till the next. Even a powerful car wash probably can't dislodge the caked on mess once solidified.
View 1 Replies
I have an 04 V6, 42,000 mi. There is an intermitent problem with the transmission. The MFI display doesn't hilite the transmission mode (P,R,N,D,S) or gear (1,2,3,4,5,6) and the tiptronic mode appears to be disabled. On occasion the transmission doesn't want to shift into higher gears. Seems to happen when the engine is cold (So Ca cold, not Mid West cold).
View 4 Replies
Mystery issue with my 2001 Accent GSI (5-speed manual, 1.6 L). I'm getting a P0300 error code and the Check Engine light (the light is like an old friend, I miss it when it's not on). This happened four months ago and I replaced the ignition coil - seemed to fix things - but now the light and the error is back with a vengeance. Car stumbles and runs rough. Changed the plugs and plug wires, but no difference.
BTW, there's a small pin hole in the upper part of the gas tank (just enough to give it a gassy smell when the tank is full) but I don't think the hole would be big enough at this stage to cause the check engine light to come on in the same way it does if you leave the gas cap off or loose.
View 3 Replies
I have a 2003 Hyundai Accent that is generating a p0713 code. I have replaced sensor and used SP3 fluid. I noticed if I clear codes everything is fine until it shifts into OD. When codes are cleared the car will not shift into OD until it hit about 60mph. The code is generated and then it shifts fine. I would not worry about it put it will not pass IM with the check engine light on.
View 1 Replies
I recently had some brake work done on my 2003 Jeep Grand Cherokee (139k miles), and they installed a new master cylinder. The following day, I was driving (very cold these days) and noticed the car had difficulty getting into higher gears and the engine revved up but would not accelerate. I had to stop, put in reverse, and start driving again. Then, the engine light popped on (P1763 - Governor Pressure Sensor) and has remained on for three days. The car runs fine most of the time, but occasionally experience the loss of acceleration. What should I do?
View 5 Replies
This is the infamous error code many Accent owners might have experienced it. The code refers to "Too lean intake system". People try to replace all kinds of parts like ECM, MAF, O2 Sensor, TPS, Fuel Pump, Fuel Filter, etc. according to my research. I just bought a 2001 Accent and the P2188 light came on. I wrote an email to Hyundai Corp. Asking what would be the most likely part that will cause the (P2188) check engine light to come on.
View 3 Replies
I don't like the way my transmission switches gears, is it possible to make the car change gears with 0.5 revs more then what it is right now... I feel like Hyundai only considered gas mileage for this car and didn't even think about the stress on transmission and engine...
I want the car to switch gears on higher revs then it is right now..
2012 Accent GS hatchback... Automatic transmission
View 3 Replies
After driving around hard for a couple minutes I got home and the car smelled like something is burnt then I went out to drive normally to get the smell out but didn't work. Then I realized my gears were hard to move into especially 1st, 2nd, 3rd. Its hard to change into those gears now. what could be the reason? What do i need to do for my gears to move smoothly again? I just got this car, my first.
View 5 Replies
So my girlfriend has an 04 elantra 2.0... the car will be running fine but then after so long of driving(maybe 15, 20mins) itll start acting strange..
It will hesitate to accelerate and shift hard and at higher rpms. Then at cruising speed it will turn off instantly(no sputter, hesitation, almost as if you just turned the key off). Seconds later the engine will come back but the gauges die and the engine will remain on.
At that point i pulled over and as i was on the brakes the car died when I came to a complete stop. Once the car completely turned off it would not start back up. However jump starting it got it going. The car is not throwing any codes.
View 1 Replies
We are having issues shifting the car it is hard to shift into gears. I have replaced the transmission and the clutch, trans mount is still good all mounts for that matter are still in great condition its getting tiring to have to slam the car into gear all the time.
View 1 Replies
