The MIL light up and I got the P0501 Code. (Speed Sensor. I use a Scangauge II and the Speed is 0 KM/H at any speed. (was working before). But the in dash Speedometer work no problem. I look on the HMAservice web page and did not found where is located the Speed Sensor.
View 9 RepliesSo I am getting a CEL and p0501 (Vehicle Speed Sensor) code and don't quite know how to approach it.
Other forums/posts suggest that I check or replace the input and ouput sensors on the transmission, but from what I understand those are each a unique code, and the p0501 is for a sensor located on the transaxle. Is this the case?
I was under the impression that because my car did not have ABS that I did not have the latter sensor on the transaxle, only the input/output on the transmission. If that is the case, will replacing both eliminate the CEL/p0501?
I had a rebuild done on my 2002 Accent. My question is now we get a code for the output shaft speed sensor. Would this have been replaced as part of the transmission rebuild?
View 2 RepliesI am getting a p0501 code (off my code reader) on my 2001 Elantra. I have already replaced the Speed sensor on top of the transaxle under the air filter. Driving into work today check engine light came back on and took to AutoZone. They are getting a P0501 code Sensor "A". They had no idea which sensor, sensor "A" was. I know there are 4 sensors on this car and have searched for other posts with no luck, all say replace speed sensor. Need to get this done to pass emissions.
View 2 Repliestrying to find the speed sensor on a 03 accent manual so I can fit cruise control
View 1 RepliesOk had a check engine light. It directed me to replace the IAT sensor.. After some research I found it was integrated into the MAP sensor. Purchased a new sensor and replaced. Drive about 15 miles CEL throws another code. P0106 (sensor i just replaced) faulty Map sensor.
Followed procedure to replace sensor.. unhook battery cable reset ecm. After reset engine is hard to start. Followed by RPM changes (assuming its the ECM re-adjusting). Then CEL flashes 5-6 times and goes out, Drive 15 miles. Map sensor code reappears. (note i only purchased one sensor But repeated install 2 times).
My thought is against wiring. since the codes refer to different signal wires one for IAT one for MAP sensor. Faulty replacement sensor?
2002 Accent 1.6L
About 3 weeks ago, I purchased a 2001 Accent GL 4dr 5spd from a friend of mine. A few days later, the CEL came on. I went to O'Reilly and got the code pulled, it was for a cam sensor input LOW. I replaced the sensor and was on my way.
Yesterday after starting the car for the first time for a few days (I wasn't driving because it needed a clutch), the light came on. Has it gone bad again or is something causing the signal to be low? Maybe a low output on the alternator or low battery? The interior lights dim slightly when the brake pedal is applied while the car is running.
So my little car.....driving home from jersey (about an hour and a half) and within the last 2 miles I notice the car just shut off. Not any electronics just the motor. Pulled over and tried to start it an it just cranks prolly no fuel or spark. happened to have my obdII scanner with me. It says camshaft position sensor(po342). Only code in there. Sounds simple enough. Got a new one and put it in. Just cranks. Plugs and wires were done about 3 months ago and I drive about 40 miles a day 5 days a week. I did the timing belt last spring so I opened that back up to make sure the timing hadn't jumped for some stupid reason. It's perfect. Noticed now after doing all of that there is some (a little) oil in the throttle body. I know about blow by and don't think I should have that much at 113k but who knows.
View 2 RepliesMy daughter spun her timing belt on her 1.5L accent. when she did, she bent the valve rods and all were replaced. The original code that was thrown was the one in the title. Ordered a new camshaft positioning sensor for the car. Looks a little different than factory. He installed it, and car is still pulling code. He accidentally threw away the original before confirmed that the problem was solved. Why the code is still pulling?? I can tell you this, I can clear the code, start the car and drive without code coming back on. As soon as I shut the vehicle off and restart, engine light comes on. Car runs fine. Had a complete valve job, new timing belt and water pump installed.
View 2 RepliesLike the title says...'02 Accent,1.6 dohc.Won't start.No spark.
Pulled code p0335-crank sensor circuit A.
Replaced sensor...still nothing.
Is there something else that commonly goes with these symptoms?...or did I just get a bum sensor?
Also,once I try starting or turn key on,I hear a buzzing coming from throttle body area for about 10 seconds even after key is off. Not sure if its related or normal.
Wife's car threw a p0711 code. It says temp sensor failure or whatever. I found the part on rockauto for 22 bucks but that's not the issue. I've tried searching about this and I seem to find some stuff about elantras and sonatas. I can't seem to find anything specific to a accent. I've read that it's inside the transmission which is fine I've changed valves before and such on old rwd transmissions. But some things I find say it's on the bottom and some say the side. Also wiring is mentioned pretty often with service bulletins.
View 28 RepliesI have upgraded my sound system in my car and sometimes i get a P0326 check engine light.
Now i was wondering if its possible that the Heavy bass ( 25/40 Hz, 1200 Watt RMS and 2500 watt Max) Subwoofers could cause the car to vibrate so much that it sets of the knock sensor?
I have read some things about it but i only found that several "Old" cars with OBDII would have this problem? Is that the same on this hyundai accent?
It only comes once in a while after long cruises and bumping.
I recently bought elantra 2004 gls, with 107k mileage.
Few days ago the check engine light came on while I was driving it. The next day it went off. This happened today also. I didn't notice anything wrong with the car, no smell, tranny fluid is recent, oil change 2.5k ago.
The code was p0501, speed sensor.
My car (jetta 2002 1.8t) have the error code p0501 even if the speedo is working. I replaced the speed sensor just to make sure.
If I erase the code, and drive no matter how far/fast I go, the check light doesn't turns on. But as soon as I turn of the car and drive again it does comes on.
My 04 Elantra GT hatch is my lifetime favorite car. Especially like the rear seats that fold flat. It has 104k miles, but I want to keep it going.
Day before yesterday the blower started making loud noises. I took car back to Pepboys who replaced the cabin air filter they put in a month ago. They had installed it incorrectly, and it shredded with a 6 inch hole in the middle, and paper everywhere. When I left, the fan was not making any unusual noises.
Yesterday I drove 20 minutes on freeway, stopped to shop, started driving, and turned on fan. Immediately the check light went on. Back to Pepboys, service manager said check was P0501 and was a transmission speed sensor that couldn't be related to the filter mess.
Last night I found the Hyundai forum and I read in a post that this is a wheel speed sensor that would be located in the right front wheel and well not far from the cabin filter. Is it possible that the debris from the fan/filter collision has affected this speed sensor? Or is this just a very untimely coincidence?
I know nothing about automobiles. What I should do next and thereafter? Is it safe to drive this car as usual until the problem is fixed?
I have an issue with my speedo. I keep getting the p0501(which comes and goes). I have replaced the VSS, CKP sensor, and I even have had my ECU replaced. Problem is the speedo works sporadically. It will work then it will stop. It will bounce around while driving then stop. Is this a cluster or issue?
I also noticed today that my fuel gauge was not being accurate it as well. It would drop then rise. My tach and temp gauge work fine as I used the tach to gauge my speed. I really would like to know what is going on.
Also, my compressor quit working and my large radiator fan quit working. I replace the FCM, but that didn't change anything. Driving with out air in the south is not fun.
2010 RX350 check engine light is on code P0500 came up it said speed sensor A...
View 1 RepliesI have a 2004 Jetta 1.8t 6speed, I recently bought it from a person(my first VW ever) so just trying to fix some things on it, One thing that I'm stuck at is My CEL, it keeps flashing the code P0501 and some random misfire on my cylinders, I have reset it and they keep coming back.
when I put about 10-15% throttle it revs up fine, no misfire or hesitation until the fuel gets cut off around 5500, which is 1k below factory red line, does not hit a thing like the rev limiter where it pegs off the top multiple times just fuel cuts off.
If i put anything above the said pressure the car then begins to misfire and lots of hesitation and that's what causes those codes to go off.
I've been reading many things pointing towards the engine speed sensor or the wiring. Occasionally my fuel/temp gauge quit working but I believe that is a separate issue all together.
So really trying to narrow down what is actually causing my engine to hesitate at low rpm.
Also i might note when I'm in neutral I can go wide open throttle and the car revs fine until the cutoff and only does the bog down when it's under full load. It sorta feels like the possible misfire is due to bad air/fuel but really do not know.
I drive an 05 Gli n my car has been shutting off on me took it for a diagnostic n the code po322 came up engine speed sensor. So my question is. Is their a DIY on replacing the sensor I'm picking it up tomorrow. To be honest I don't even know where the sensor is located...
View 8 RepliesThe check engine light came on in my 1997 Honda Accord and the OEM diagnostic says it's PO501 which is a performance problem in CVT speed sensor circuit. My mechanic is on vacation. Is it safe to drive short distances until I can have it fixed?
View 7 RepliesWhere the knocking sensor is located on a 2005 Accent. I am in need of finding it so that i can wire a controller into the signal wire?
View 2 Replies