Accent LC (2000-05) :: No Reverse - P0732 And P0734 Codes Thrown
Aug 12, 2013
I have an 02 accent with 1.6 that has no reverse and throws P0732 and P0734. How to repair?
View 5 Replies
Aug 12, 2013
Advertisement
Ford Transmission :: Long Shifting Into Next Gear When Selector Is In Drive - Code P0732 And P0734
I have a 2008 Ford Escape 2.3L V6. About 67K miles on it.
Recently there's been some transmission problems. When the selector is in Drive, it will take abnormally long to shift into the next gear at normal speeds, and will redline if i hit it hard, but if i let off the gas, it will shift. Never hard.
If I put the selector in 2, it will do the same thing, eventually shifting into that second gear.
Gear selector on one, well, it obviously stays in 1st.
Reverse is fine. All shifts are smooth just take forever, and I get the wrench in the dash (means drivetrain/throttle fault as per manual) only after driving a while. The tranny fluid is still very clean, and this as been going on for 2 months.
Ive taken it to about 6 different places. Half say new tranny off the bat. Other half says clean fluid for that long after the problem started means its def. an electrical problem, and that makes the most sense to me. What it could be?
I'm thinking:
-Tranny Range Positioning Sensor
-Input/Output speed sensor
-TCM reprogramming/replace
- I'll even go with reflashing the PCM.
Accent LC (2000-05) :: Transmission Slipping - Code P0734
So I bought a 2000 Hyundai Accent for my 16 year old daughter and the guy sold me a car that has a slipping trans. So I went to the Autozone and had the codes pulled and it was a P0734 code. I replaced the trans fluid and replaced the internal bearing and shim with the 42220LK kit from whatever it takes transmission parts store. Trans still slips. What else or should I just unload it?
View 3 RepliesAccent LC (2000-05) :: P0734 Error Code - Hard To Shift Into Higher Gears
I inherited this car from my grandmother when she passed. It has low miles, around 40k. Since I paid zero for it, I would like to keep it. Historically I have done all my repairs, but never trans work.
Here are the symptoms. The car has issues shifting into higher gears. I have to punch the gas and then it will switch gears. It then began to do this for reverse, and now now reverse does not work at all.
At first I thought it was a speed sensor problem, but when I took it in to be read, it came up with P0734. It could be electrical (Speed sensor?), low fluid (it's not low), or 4th gear.
Is this transmission worth me fixing or paying to have it repaired, or should I move on?
P.S. If I drop the pan and find shavings, I understand that to point to 4th gear and bearing (also what the computer code read as the issue). Do shavings mean it definitely is 4th/bearing, or could it be another blown part?
Passat (B5) :: 1998 - ABS Light On But No Codes Thrown
98 passat 1.8t has the abs light on and the exclamation point. Scanned it using vad. Nothing showed up in the scan. Also turbo whistles under load. And trans slips. Nothing showing up on vad.
View 3 RepliesGolf IV / Jetta IV :: 2003 1.8T - Reverse Not Engaging On Cold Starts / Code P0732
I am having a problem with my MKIV, @ 182k. I think problem first arose a couple months ago when reverse began not engaging on cold starts, so I would have to sit there 5-10 minutes waiting for car to 'warm up' enough for reverse to engage. This led me to taking it to a local tranny shop who I asked to change fluid only, which they did. Problem persisted however, but forward driving was noticeably much smoother. If that matters. I gave up on it, since I knew it was only reverse messing up, and started parking in reverse overnight etc.
Simultaneously I had a code for P0420/P0411 (the SAI incorrect flow crap which causes catalyst inefficiency) so I went ahead and swapped out the cracked SAI plastic hose leading to stock airbox, after doing so I reset the CEL and ran the car. And it ran like crap, I think it was in limp mode (i had never experienced this in my Jetta) from what Ive read, but not sure. So, I pulled to the side, and restarted car, let it sit, same problem. Finally, after 3-4 cycles it threw a CEL, which ironically FIXED the problem. It ran fine from then on. Made it home, hooked up scanner and CEL code was P0732, which I read elsewhere is a 'Gear 2 - Incorrect Ratio' meaning 2nd gear is messed up somehow.
So, overnight I reset CEL and today in the morning I let it idle for 10 minutes before taking off, immediately same issue, where car will not accelerate/ change gears it seems. Went back straight home, waited for CEL to display, and VOILA, runs fine again. Same code P0732. Running fine as of writing this. Problem only arose after taking a swing at SAI code and reset of CEL's. Once CEL lights up its fine.
Ford Super Duty (1999-2016) :: 2001 - Transmission Malfunction - Sluggish - Codes P0732 / P0720 / P0503?
My '01 7.3 is having some transmission problems, My O/D light is flashing. Trying to go after stopping at a light is a difficult, it drives very sluggish, like its not in overdrive. Scanned it and got three codes P0732, P0720, P0503. I replaced the ABS/VSS on the differential and the problem still exist.
View 1 RepliesAccent MC (2006-11) :: Engine Was Idling / Little Rough And P0302 Code Thrown
So I bought my accent used a couple months ago. It is a 2007 SE 3dr 5spd manual. It ran nice during my test drive and the price was right so I bought it.
Now I'm wondering if there is any way to find out the service history on the car...at least the major one's (30k, 60k)?
I ask because recently the engine was idling a little rough and it threw a P0302 code so I changed the spark plugs and holy-cruddy-deposits-batman those things were black. Gapped the new ones and popped them in and its a noticeable difference. My CEL keeps coming on and throwing a P0496 code as well, virtually once every tank of gas. Its not the gas cap so my next step there is to check the PCSV and hoses.
With these little problems, it makes me wonder about any larger issues. I know the timing belt on these things is supposed to be replaced at 60k. Additionally I would be willing to bet that my ECM software is out of date. Would Hyundai have records for any of the big maintenance milestones since they are required for warranty work?
How much does it cost to have a dealer check your ECM software and update it if needed?
Accent LC (2000-05) :: CEL On / Codes P1505 And P1507
I have a 2002 hyundai Accest LC with a 1.6 ltr.-my CEL came on-ran the diagnostic and codes p1505 & p1507 came-up-is this a big problem or can I wait to repair 1-2 mths. What could the possible causes/fixes be?
View 1 RepliesAccent LC (2000-05) :: Codes P1402 And P1403
What it does means that codes and how solve them is about dtml? How check it?
View 3 RepliesAccent LC (2000-05) :: Sputtering Quite A Bit In All Gears / CEL With Error Codes
Recently bought a `01 Accent 5 speed.. First question . How do I tell if its the 1.5 or 1.6 ? That will really point me in a good start. Ha... Ok.. Check engine light is on and I found a paper in the glove box with some of the codes wrong with it.. The one I focused on was telling me the fuel system was to lean . blah blah blah... Dont remember the exact code as I felt that my research was good and I replaced the MAF sensor... Didnt clear the code...
Also it was sputtering quite a bit in all gears mainly at low rpms. I did change the fuel filter , checked plugs and wires etc.. Now I replaced the MAF sensor and it has not solved the problem.. Took it to have it rescanned and have been given codes p1127 and p0136 .. both seem to relate to the Bank 1 sensor 2 O2 sensor. question is I have saw the "upstream" sensor located right below the exhaust manifold but did not see a second sensor?
From what I have gathered sensor 1 does the most work, so I`m curious if these 2 sensors are interchangeable? Could I buy the downstream sensor and if that does not solve my problem , take it out on try it in the upstream sensor? Also do you really feel as though just changing that sensor will "cure" my sputtering issue? the car only has 88k on it and seems to be in good shape otherwise.. I really need this check engine light problem fixed so I can get inspection..
Accent LC (2000-05) :: Getting Codes For Multiple Misfires On Cylinder 1 / 2 And 4
I have a 2000 lc 1.5l ... I just rebuilt the motor machine shop work and all it Will start and run for 3 seconds and then die. If I hold the gas pedal it will run but sound rough and as soon as you let go it dies I have been able to get codes multiple misfires, misfire cylinder 1, misfire cylinder 2, and misfire cylinder 4 I have put brand new plugs (copper core ngk), wires coils, crank sensor, cam sensor, iac, tps, maf and the injectors all have new orings it also has ntk o2 sensors that might have 1000 miles on them...
View 1 RepliesAccent LC (2000-05) :: CEL Fault Codes P0304 And P0441
Car - 2004 Accent auto.- 1.6l - 97K miles
After battling a few months to get my check engine light - fault code P0304 to go off I finally remedied the problem with 3 bottles/fill ups of STP Gas treatment. This was about 1500miles ago. I go to DMV Inspection station and sat for an hour then wait anther 20minutes for the test to end and was given the big fat rejection sticker, she failed because the check engine light came on with fault codes P0304 & P0441.
Now what the heck happened here? Just bad luck and coincidence or did their test set it off? Anyway the P0441 code is new and researched it is the Evaporative Emission Control System Purge Valve. Okay where is it, the HMA manual is not specific? In relation to the intake manifold where is it? Easy fix? And will this solve my P0304 code?
Accent LC (2000-05) :: Car Doesn't Want To Go In Reverse And 5th Gear
Just bought a 01 Accent hatch the other day. It's a 5 speed 4cyl. First gear through 4th have no problems. If I try to shift into 5th gear or reverse, the car doesn't want to go into them. The dealer I got the car from said that the problem is with a pin or something. I have never bought a Hyundai before this, I've had old 70s american cars. I was thinking it could be a shifter linkage but I figured I would ask you knowledgeable people about it first before I go and break something trying to fix something simple (hopefully simple.
View 8 RepliesAccent LC (2000-05) :: Engine Dies, No Fault Codes Appeared
Recently my daughter's 2004 Accent will die out without warning usually at stop lights, and will be hard to restart, usually after numerous attempts. It will crank over fine. This has been very intermittent. I have checked for fault codes, there are none. I haven't been able to really determine the cause because I have not duplicated the issue. I have replaced the fuel control module located on the driver side kick panel after reading about problems with this module, but it did not remedy the issue.
View 4 RepliesAccent LC (2000-05) :: 2001 - Cannot Clear Codes P0123 And P1605
My 2001 Accent (Manual Tranny) with 95,000 miles needed the head rebuilt due to the timing belt slipping and making a mess of the valves. The car threw no codes before the mishap and ran perfectly but now shows the codes P0123 and P1605 after the rebuild. The shop that did the work said they spent 5 hrs trying to figure why these codes are showing. They swapped out the TPS which didn't work. I'm not sure if they swapped out the acceleration sensor. Anyway, since I picked up the car,it was idling low at about 500 RPm and fluctuating in neutral (remember its a manual. In the week that followed, the car wouldn't start a few times which I found out to be a loose negative terminal on the battery. Since I fixed that problem, the car idles at about 1,000 RPM when I start it but then jumps up to about 2,000 once it's warmed up or if I downshift and then throw it in neutral! And yes, the same 2 codes show up on my scanner.
View 3 RepliesAccent LC (2000-05) :: Rough Idle While Drive Or Reverse
I have a 2000 Accent with about 150,000 miles on it. Recently I have noticed that when my car is sitting in an intersection, the car appears to idle roughly. I would't exactly say that the car is idling rough, cause it stays at a consistent RPM while in drive or park, but the engine gets louder and the steering wheel starts to vibrating. When I slightly step on the gas, the vibration goes away. Also, when I put my car in park or neutral, the car quiets down and the vibrating stops.
I was wondering if it could be the throttle position sensor, or maybe a broken motor mount, but I haven't had a chance to look into it it. I did replace the purge control valve last week, which slightly improved the vibrations.
Accent LC (2000-05) :: Scrapping Noise Quiet Down When In Reverse
What this sound is? I thought it was the brake pads so I tried to change them and broke the bolt on the caliper (both sides). Long story short, the car now has new pads, rotors AND calipers. But i hear this scraping sound. Follow the link to a youtube video. It speeds and slows with the car and doesn't change when i apply the brakes but seems to quiet down when I'm in reverse. Wheel bearings seem unlikely since the sound doesn't change when I turn the wheel to either side.
Video: [URL] ....
Accent LC (2000-05) :: 2001 GL Transmission - Reverse Gear Went Out
I have a 2001 Hyundai Accent GL the reverse gear went out but all the forward gears work. Ive been told that I need a new transmission. I found a great deal on a transmission from a 2007 Hyundai Accent. Will this transmission work in my car?
View 1 RepliesAccent LC (2000-05) :: 2003 - Squealing Noise In Reverse
I have a 2003 Accent with 30,000 miles on it... It is making a variety of noises right now but the latest and loudest is that when I am backing out of parking spot or something like that it makes an awful squealing noise... What that might be?
View 2 RepliesAccent LC (2000-05) :: 5 Speed Slams In Reverse With A Bang
I have a 2001 accent 1.6 5 speed manual. When I put it into reverse it dont fully engage until I give it some gas and then it slams into reverse with a bang. I am not really sure but I think it only does this with the car is cold I may be wrong though it started this a few weeks ago.
View 3 Replies