Accent LC (2000-05) :: Immobilizer Control Module Replacement?
Mar 5, 2010
2004 Hyundai Accent
- Car won't start ...
- Remote key unlocks the car fine
- When put the key in the ignition and turn 'on' the little key indicator on the cluster doesn't come on.
- Left overnight and tried again in the morning, key indicator come on and then disappeared and wasn't able to start car.
- Key indicator now won't come on.
I spoke to mechanic and he said replace the immobilizer control module and reprogram key..
View 5 Replies
Advertisement
Recently I've had problems with my DRL (Day time Running Lights) Control Module. When I start the car, the DRL starts to make a loud buzzing sound. When I turn on my High Beams, it stops making the noise. It sounds like there's a relay that Isn't working like its supposed to be. So, I've thought of replacing it, but I`m not sure if its the DRL that's defective or just a wiring problem...
View 1 Replies
I'm getting ready to replace my passenger side control arm after it had broken. Is it recommended to change the drivers side too? Is is also necessary to get an alignment?
View 4 Replies
I have had the keys recoded 9 days ago and two days ago they started playing up again, today I phoned the mob I paid $150 to recode my keys and they're going to look at it again (for a small fee) despite it their work being faulty, is there anything else that could be causing this? It will sometimes take 20+ turns of my key before it registers.
View 7 Replies
Anyway my issue is, my car is turning over but wont start. I notice that it will only start when the yellow immobilizer light comes on and then goes off.
If I try to start when there is no immobilizer light it wont fire up.
I have to take out the key and wait 20 secs. When I turn back on the ignition and I see the yellow immobilizer light, I know it will start?? The immobilizer light goes out when the car starts. Whats up or should I continue what I'm doing...
View 1 Replies
I have a 2012 prius c and just replaced the body control module - no problem there, but now the ac and fan will not turn on. Fuses visually look ok (I don't have a tester) and they had been working previously. I live on Molokai - no prius mechanic on the island so I do my own repair when I can - how to diagnose the problem?
View 4 Replies
2004 f150 - Airbag light was flashing. Received recall letter. Dealer replaced a wiring harness. Dealer did not confirm functionality of airbag prior to leaving shop. Light continues to flash. New diagnostics from dealer says error code 1885 - the control restraint module needs replacing in P&L. Does the code match the fix? Can a novice mechanic replace the module?
View 2 Replies
I was told that their is an AC control module in the dash. As I have a 2000 that we are still getting parts, where in the dash this control module is?
View 5 Replies
My 06 accent GLS has become difficult to start only after refueling, which I'm guessing is related to a bad purge control valve from what I've read. Where exactly is the valve located, and is this something that someone with relatively little automotive repair experience could do on their own? I think I've located it on the backside of the engine near the air intake.
View 2 Replies
I just finished replacing my timing belt, water pump and all belts. I made sure to double check the timing marks lined up via this pic:
Timing belt diagram
I put everything back together and no go. I am not sure what to do now. Should the crank sprocket pulley be in a special starting position? I see is has a "1" engraved on it.
View 22 Replies
How to fix SES P0670?? I understand there's a whole procedure on checking fault.
P0670:GPCM Glow plug control module control line failure. Open/grounded circuit, open/shorted GPCM, failed PCM
But how did you resolve problem? replaced GPCM, found open circuit, short --if so where?-- or replaced with updated harness.
(4C3Z-12B568-AA connector upgrade kit as in picture)???
View 14 Replies
Replaced this gasket that seems to be leaking oil. Looks simple enough, is there anything i should do or know before taking on this job? It's a 2002 Accent GS 1.5L ....
View 8 Replies
So I installed a new radio in my car today and connected everything besides the dimming and illuminating wires since my new head unit didn't have one. I connected everything that i needed to like ground power and power from the ignition switch. Radio doesn't turn on at all.
After installing this new radio the climate control doesn't light up anymore. Checked all the fuses under the dash on the driver side and under the hood. All of them are good. Is there any other reason the head unit and the climate control lights wouldn't work.
The clock, a/c and the thing defroster lights work. same with the ash tray light. seems to me that the only light that isn't working is the climate control light and the radio doesn't power on at all.
View 13 Replies
Alright, after taking everything off and replacing all the joints/bushings, I am left with the control arm. (it hasn't been easy either)
I am at the control arm (Passenger side) and i got the rear bushing loose. I managed to brake the front one loose, with a lot of force, but it spins. I see in HMA that it has a bolt, or so it appears, but how on earth do you get to that?
View 13 Replies
my ignition immobilizer would not let me start my 2000 Acura several times during the past week. seems to start fine after a long cool down, or after sitting over night, but after a short trip it acts up, sometimes taking as long as 1 hour of repeated attempts to start. is this something as simple as changing the key fob battery, or is it in the ignition, or is it something in the shifter?? i only have 68k miles.
View 1 Replies
My buddy with his 2000 jetta 2.0 that starts then stalls. The immobilizer light turns on and off again as it should during the starting process. Tried reprogramming the key with the 2 key programming process, also tried removing power from the battery and touching the leads together but these are fixes for the immobilizer but the light doesn't stay flashing. Is there anything I can try while waiting for my vag-com scanner to be delivered....
View 1 Replies
Looking for info on replacing ABS module themselves? I was wondering how difficult this job can be.
View 4 Replies
I own a VW GTI 2010. I replaced my abs module from 1K0 907 379 AM to 1K0 907 379 BE which is compatible with Park assist 2.0. I tried to code it with the previous coding with 00 added at the end but it got rejected. Since, then I've been trying very hard to code it.
I've tried at least 20 different coding some on which were provided by "16 D", a member friend in the forum, but they were all rejected. I still don't understand why other people were able to recode their module with the same previous code with 00 added at the end but I cannot. Is there any chart for generating such long coding?
View 2 Replies
Had I to break into my gas cap, replacing the module? is it ok to buy a used one? My door locks quit working too. the same module right?
View 1 Replies
I need to locate the part number, so that I can order from salvage. Where this is located on a 2000 Passat?
View 3 Replies
I have a volkswagen jetta glx vr6.Today my key wont turn (unable to crank engine) and the car won't detect my key (no remote entry/lock function).I've detached the battery.
Plugging the batter back and keeping the key in:
1. Off position causes the "Electronic Immobilzer" light to blink.
2. When in on position. no "electronic immoblizer light comes on.
3. In anycase I can't get the ignition to work.
My engine check/airbag lights are also on and my radio/ac doesn't work. Also the electronic controls for rear view mirrors don't work. Half of the tail (exaust) pipe rusted and has fallen off.On the funny sideI asked the guy at VW to appraise my jetta for a trade and he said it would be $500 for the car !! ONLY After the company official tested the car this won't start...the sales person left, since it was 6PM on Friday. I was left alone and had no option other than to leave my car at Pugi VW showroom and ask a friend for a ride...Long story.
View 4 Replies
