Accent LC (2000-05) :: Fuel Light Flashing / Misfiring And No Spark
Aug 4, 2011
I own a 2000 accent. Broke down, called racq, they said it was electrical problem with fuel pump and my car would kick over after someone cranks it and another person bangs the underside of the fuel tank a few times(exterior). then broke down again and car wouldn't start at all, had no spark would only crank not kick over, I took it to a mechanic and he found out it was the fuel relay switch so he replaced that and the car was running again, however it was only running on 3 cylinders and the fuel light would flash/turn on for seconds/ flick on and off even with a full tank.
Took it back to the mechanic and he said the fuel lines were blocked and needed new fuel filter so after he fitted all that was still running terrible, would misfire, fuel light still flashed and driving it around drank the fuel. Found out that it was the first cylinder that was the problem. I changed the sparkplugs and no difference
So I went to a car wreckers and replaced the 1st fuel injector (got it for 5 dollars off an accent that was wrote off from the back end) once i fitted the injector it started to run better. It is now running at about 75%. doesnt go as hard as it use to, still misfires, still drinking the fuel and the fuel light is always off and on when I am driving. It has low revs in idle mode so it rattles/shakes heavily as well and smell of fuel in the back seats every now and then.
oh and a side note - drove it a few nights ago and the clutch pedal is 'loose'... as in the grab is near enough clutch in 7/8ths of the way(near the floor) and when the clutch is fully out there is alot of 'play' which is when you press the clutch in a quarter of the way its nothing, no tension or anything just floppy, but im not 100% sure if the clutch cable needs tightening or something worse( i only replaced clutch about 2 months ago so it couldn't be burnt out?)
View 3 Replies
Advertisement
If you get a f!ashing cel ,the next time you start it should it flash right away or can it go back to solid on cell? 02 Accent 1.6 130 k. What can be done to check the flex pipe for a leak? Can you spray water or what? The outside looks good. Also looks hard to check around intake manifold for leaks.
View 11 Replies
2014 Accent 14,000 miles
Filled the tank and shortly thereafter there CEL started flashing and the car sounded like it was missing. It was towed to the dealer, and they said they cleared the light and could not get it to happen again.
When I next drove the car it ran fine for 20 minutes, then it started misfiring and the CEL started to flash. Had it towed to a different dealer, and they said the same thing. Cleared the light, but couldn't get it to happen again.
On the way home form the dealer, after about 20 minutes of driving - the same thing. Today, I started the car in the AM no light and running fine, drove around and town and in exactly 20 minutes it was misfiring again.
First dealer said it was a P0302 code.
View 4 Replies
I have been experiencing some issues with my '06 rio5 (same engine as your hyundais). this forum is way more active than the kia forums, so figured id give it a shot here.
I am experiencing a rough idle at start up while the car is low on fuel (<1/4 tank). it idles rough for a few seconds, the check engine light flashes a bit, and then it runs fine.
The car is an '06 rio5 with approx 19k miles on it, five speed manual. Also, sometimes after refueling and it will just shut off while waiting at an intersection. Not sure whether these two issues are related, but thought i would mention it just in case they were.
View 14 Replies
I have a 2000 accent. Automatic tranny with 167000 miles. My current problem is the car is misfiring upon acceleration and engine revving. I have to accelerate very slowly to minimize this but i once the engine revs up enough I can give it more gas and it will rev normally with plenty of power. I have had to unplug the maf to keep it driveable. Ive never had a car stay running after disconnecting the maf so this is strange to me. My accent barely stays running with the maf connected. I just got the car from my dad and he had it fixed and it ran good for awhile with the maf connected so I don't think it is the maf. But the same problem came about and we had to disconnect the maf again. And he cant remember or is not sure what was exactly fixed on the car. I've read up about the purge control valve and havent had a chance to check it out but some of the symptoms fit.
View 21 Replies
I have a 2002 Hyundai accent 1.6L w/ 190,000 miles. Around Christmas one cold morning right after getting gas at a grimey service station my car started running like crap misfiring badly. Kicking and bucking it barely got me to work (6 miles). I took the car to an Advanced auto and had them plug it in to check the engine light. It was throwing multiple codes P0300 (Multiple Misfire Detected), P0301 (Cylinder 1 Misfire Detected), P0303 (Cylinder 3 Misfire Detected). I told the guy at advanced that I thought it was bad gas and he agreed, so I put some dry gas and Lucas oil gas treatment in it. The problem seemed to get better within 50 miles, only misfiring when I drove it hard.
The problem has come back and this time the gas treatments are not working. I am getting the same two codes along with a new code P0133, (HO2S-11 (Bank 1 Sensor 1) Slow Response) and the same symptoms, and to top it off my flex pipe has rusted out (for the second time).
So now I don't think the initial problem was water in the gas, and I am not sure what to make of it. The problem seems to happen more noticeably when I push the engine (first gear, and when accelerating) but then seems to get better when maintaining a constant speed. Also, the misfiring happens all the time but more noticeably when the engine gets to running temperature. First gear is by far the worst when the engine is warm.
- The car got a tune (filter(s), plugs wires) up about 6mo ago
- The timing belt is old about 90k on it
- A new crank shaft position sensor a year ago
- New O2 sensor (the 2nd one past flex pipe) 6mo ago
- Burning about 1qt of oil (synthetic) every 3k miles but no smoke
- The car has the original clutch w/ 191k on it!
This is where I stand. I don't care about the flex pipe or the timing belt. Unless I can defiantly pinpoint the problem to one of those two, the car has so many miles on it, to start dumping that kind of money into it doesn't make sense. I have put a spark test light on each of the plugs BUT the problem does not happen when the car is idle so it showed me nothing but properly functioning plugs. I was thinking the ignition coil (its original) but I think that would throw a code.
View 20 Replies
I have a 2002 Hyundai Accent 1.6L automatic. I just bought it today. It has 171,000 miles. The car is misfiring. It does it when I give it gas. It won't misfire if I only give a little gas but if I was to drive it then it spits and sputters. I put new wires on. what are some common things on these cars. I am new to a Hyundai.
View 3 Replies
I have an 02 Accent 1.6L that has about 190,000km on it. It is now misfiring under low rpm's (anything under 2000) and the engine light will flash and then go off after about 5 seconds. Once the engine light went on and stayed on but I got the code read and reset it. The code was P 0303 Cylinder 3 misfire. I replaced the coil pack since that is apparently the common cause of this issue.
No luck with the new coil pack still have the same problem. I started smelling gas about 1000km ago so I assume that it is burning rich and putting raw fuel into the engine. My spark plugs are under 10,000km new and the wires show no signs of any problems. My next thought was to buy a new MAF sensor and hope that is the issue.
What this could be? FWIW the engine seems to run a little better for about 5km after using a throttle body clean on the TB. It also runs minimally better when I use a Lucas fuel additive.
View 5 Replies
I have hyundai accent 2005 1341cc 86hp, with BRC LPG kit. When i start the car at the morning, the engine misfiring around 500rpm for a few second (5sec-10sec)...
Sometimes the engine start ok in the 1100rpm - 1200rpm and when I touch the accelerator then misfiring again!
The car have 133.000km (11.000km with LPG).
I have replace the petrol filter 2 days ago and the all electric system without multiplier. I have clean throttle valve and the injectors with stp cleaner.
View 26 Replies
Yesterday out of no where my rio started to misfire so i immediately took it into autozone to have it checked. when doing so the check engine light was on, but solid.
The tests came back with P0300, P0301, and P0302 or 3. I cant find the papers, but its 3 cyns that are misfiring. The guy at autozone suggested i try changing out the plugs first since its cheaper and has been known to fix this issue.
The second I bought the plugs I went home and changed them out. once finished i started up the car and not only was the car still misfiring, but the check engine light is now flashing... I did notice one thing when changing the plugs.
If facing the engine the second coil from the left had a bit of what looked to be rust. i was able to wipe it off with ease. What my next move should be?
View 9 Replies
So a few days ago my engine developed a misfire, flashing MIL light etc...long story short it was cylinder 5's ignition coil. When we scanned it, we picked up a misfire on cylinder 5, and a slight misfire on cylinder 1. Replaced the coil, as well as new spark plugs, cleared the codes, and everything was peachy.
NOW, driving home today.....once again. Misfire, MIL light etc. I'm not a mechanic so I am wondering if it is common for all the coils to go around the same time, or if this is probably just cylinder 1 now going. I'm going to once again get it scanned, but before then...is there anything that could cause ignition coils to just start going bad, other than age.
View 9 Replies
I got a 99 1.8t. Here's the deal, misfiring at idle, flashes battery light. alt and battery was checked and there great. it has a maf code, so I unplug the maf and still get the same misfiring. maf was fine be4 i tried cleaning it, now it throws the code. it had misfiring be4 i clean it also. next problem is it stutters and misses if i go wot in 4 or 5 gear and the batt light flashes it doesn't throw a misfire code. Also if I am idling and i floor it, it stutters and misses at lower rpm rage and then is fine at higher rpm range. i replaced plugs and gapped em right, i did a power balance test and the coils all are firing so is the injectors. I don't got vag but i do got a good obd2 scanner i was looking at the data wen car was off and i seen that if i floor it the tps only reads 77.7% . Also my timing says its 12 degrees and idle fuel pressure is fine i checked with a gauge. Pretty much misfiring with no codes thrown and flashing battery light.
View 17 Replies
I'm completely lost. My car won't start. It will turn over but not get a spark. I replaced the plugs and the camshaft position sensor and still having issues. I didn't change the wires when I did the plugs. Would that cause the problem to persist?
View 29 Replies
2005 Accent has been essentially bug free until now.
Drove 3 hours, parked for 4 hours, then when to turn it on... cranked, no turn over. Tried again and the crank died. I figured, ok, no problem, battery getting long in the tooth, time for a new one.
A friend and I were able to push start it (5 speed manual), and yesterday I bought a new battery for it. No worries right?
Wrong. Same thing now. Cranking but no gas/spark/turn over. No check engine light or codes.
My next place I'm guessing I need to check is the fuel pump relay? Should I hear a click a few seconds after I turn the key to on? I believe I should, not sure if my memory is playing tricks on me, but right now there is none.
Relay in the fuse box? Do I need to check anything else first? Have multimeter.
View 4 Replies
So it finally happened...One day she was working just fine and now is dead. OK, starter is working, battery is new but there's absolutely no spark on any of the spark plugs. I wonder what could it be ?
View 8 Replies
My wife's 03 accent cranks over good, but won't start. It does fire some but won't start. I tried squirting starter fluid in the intake and that only made it fire less. Spark is strong on all four cylinders. At first I thought I found the problem because it had weak spark on the middle two cylinders and i replaced that coil pack and now all four are strong, but still same problem.
She drove it home and parked overnight, and in the morning it wouldn't start. I don't think it is the timing belt. I replaced it not too long ago, and I took a peak behind the top of the cover and all still appears to be as it should.
I am now at a bit of a loss. I mean it has good spark, won't start with starting fluid, so what could it be?
View 3 Replies
I have a 1996 ford taurus lx v6 3.0 dohm..my check engine light flashing. then it stop flashing..i did replace spark plug,wires,coil pack..when it start to flash i put it gear the car start to shake and sputter.i really don't know why its doing that the car has about 150000 miles on it..i do get a code p0302 Cylinder #2 Misfire..the new plugs and wires and coil pack is about 2 weeks old..
View 11 Replies
My 99 Explorer XLT V6 SOHC has been misfiring lately. In idle the RPM needle fluctuates a bit and the vehicle vibrates and shakes. At night when the lights are on I notice them dim a bit as the engine struggles in idle. It doesnt stall very often at all. Accelerating I notice way less power and the engine studders. Thats when the engine light comes on flashing. Then remains on solid afterwards.
I brought it to a mechanic friend who read the code and it was cylinder two misfire as well as O2 censor. I replaced the plugs and leads and censor. Noticed the plug in cylinder two had little to no gapping. Thought I had fixed the problem. Vehicle ran perfect. Three or four days later driving on the hwy same problem came back. Thinking it must be the coil pack I got one for a good price and replaced it.
Again, the truck ran great for four days and now the problem has returned. Same thing, shaking studdering and flashing engine light. I have verified the locations of the wires and plugs a few times so i believe they are all properly installed.
View 7 Replies
I have an 05 accent and about 6 months ago I started to notice a clicking sound coming from the belts area ( it sounds exactly like a BBQ grill igniter when it's pressed), the sound starts as soon as I start the car and stays pretty much the whole time, I had the car lifted by my mechanic and he discovered the problem in one of the belts ( not sure what is called but it's the one at the very bottom of the belts, the first one you see when you lift the car ), the spark is seen at the edge of the pulley or where the belt sits on the pulley. The mechanic was puzzled about this, he recommended replacing the crank sensor as a first step, the car runs fine and there is no other symptoms or issues
View 2 Replies
Like the title says...'02 Accent,1.6 dohc.Won't start.No spark.
Pulled code p0335-crank sensor circuit A.
Replaced sensor...still nothing.
Is there something else that commonly goes with these symptoms?...or did I just get a bum sensor?
Also,once I try starting or turn key on,I hear a buzzing coming from throttle body area for about 10 seconds even after key is off. Not sure if its related or normal.
View 2 Replies
I have a hyundai accent 2005 sedan (automatic transmission). The vehicle is a NON-US model. My gas consumption is approximately 7.3km per litre which is very high.
The spark plugs have been replaced , tires are at 30psi , and air filter is new. The spark plug cables are also new. The obdII device does not detect any issues and the engine check light is also off.
View 42 Replies
