Accent LC (2000-05) :: Engine Sputters When Try To Accelerate In Higher Gears
Feb 25, 2013
I own a hyundai accent 2000 GLS, i have recently replaced the ECM wiring and a brand new ignition coil, however the engine still sputters when i try to accelerate in higher gears, my mechanic told me that the engine mounting bushes need replacement. is it one of the causes? the sparks plugs are new, fuel pump is working fine.
View 7 Replies
Advertisement
I recently had some brake work done on my 2003 Jeep Grand Cherokee (139k miles), and they installed a new master cylinder. The following day, I was driving (very cold these days) and noticed the car had difficulty getting into higher gears and the engine revved up but would not accelerate. I had to stop, put in reverse, and start driving again. Then, the engine light popped on (P1763 - Governor Pressure Sensor) and has remained on for three days. The car runs fine most of the time, but occasionally experience the loss of acceleration. What should I do?
View 5 Replies
I inherited this car from my grandmother when she passed. It has low miles, around 40k. Since I paid zero for it, I would like to keep it. Historically I have done all my repairs, but never trans work.
Here are the symptoms. The car has issues shifting into higher gears. I have to punch the gas and then it will switch gears. It then began to do this for reverse, and now now reverse does not work at all.
At first I thought it was a speed sensor problem, but when I took it in to be read, it came up with P0734. It could be electrical (Speed sensor?), low fluid (it's not low), or 4th gear.
Is this transmission worth me fixing or paying to have it repaired, or should I move on?
P.S. If I drop the pan and find shavings, I understand that to point to 4th gear and bearing (also what the computer code read as the issue). Do shavings mean it definitely is 4th/bearing, or could it be another blown part?
View 4 Replies
My standard 2002 accent is undriveable and at the mechanic right now (100,000km). For the past few weeks the car has driven very jerky. While in first and second gears if i accelerate too quickly it just jerks/slips and has very little power.
Yesterday the check engine light came on and i got codes P0300, P0302, P0303...misfire in cylinders 2 and 3. Checked this forum and decided to buy new spark plugs (last replaced plugs and wires 1.5 years ago). Got into the car and could go more than a block because it was jerking and then kept stalling. Replaced the sparkplugs and nothing changed. Had it towed to the mechanic...after a few hours he said he had cleaned the exhaust manifold and it was driving fine. I picked it up and a block away it stalled again.
The mechanic now says 3 of my fuel injectors need to be replaced and the fourth will probably go soon and it will be about $700 to fix. Does this sound right for these codes?
I called hyundai parts and they told me each injector is $236...he also told me he doubted they had to be replaced cause he has never seen an accent have fuel injectors replaced and also they rarely sell these injectors, he said it was probably something electrical.
I have found 4 injectors on ebay for $200 but is this really the problem? The mechanic says it is 100% the problem. But from reading the forum I dont think so.
Also wanted to add that i often noticed the smell of burning plastic. Smoke seems to be coming from spark plug area when i notice the smell but nothing looks burnt/melted.
View 14 Replies
I don't like the way my transmission switches gears, is it possible to make the car change gears with 0.5 revs more then what it is right now... I feel like Hyundai only considered gas mileage for this car and didn't even think about the stress on transmission and engine...
I want the car to switch gears on higher revs then it is right now..
2012 Accent GS hatchback... Automatic transmission
View 3 Replies
One morning I went to start my 2000 Accent, 1.5L Auto and the engine couldn't get going. I had road service come look at it and they said the problem was the fuel pump, I then got the car towed home. I changed the fuel pump and everything was working great again. I then changed the fuel filter, air filter, oil filter and flushed/refilled the oil. I used the car very lightly for a few days and had no problems.
Then yesterday I took the car about a 30 min drive, when on a main road my engine begun loosing power and I couldn't accelerate, as if the engine was not getting fuel. I managed to pull over safely and after about 30 mins of not getting anywhere I decided to hit around my fuel tank/pump with my club lock many times and what do you know the car starts and I manage to drive it about 25 mins, I was almost home when the same thing happened. I pulled over, waited, hit the tank and finally drove all the way home.
When I originally changed the fuel pump everything seemed fine, the plastic pump housing and everything attached to it appeared in great condition. So my hunch is that the problem would be where the fuel actually enters the engine block? The way that everything works fine until driving for roughly 25 mins makes me think the problem may be dependent on the temperature of the engine, given that's the main variable that changes?
View 1 Replies
But i still have the sound, and it definitely sounds like its coming from the passenger side, however when i looked at everything and tried wiggling the wheel, nothing seemed out of place. Would that still indicate a bad ball joint? Is there anything else i should inspect/have inspected?
The sound only happens when i go over a big bump, or a medium bump at a higher speed. It doesn't seem to affect my steering or driving feel, but its still not a noise that should be there.
I found that the driver side tie rod was a little loose, and replaced that, but sound persists.
View 3 Replies
own a 2005 Hyundai accent 1.6L engine. I replace the engine today. The previous engine had internal damage. The transmission I left alone. I didn't disconnect the wiring. I only removed the engine. The transmission worked flawless. When I turned on the car the engine sounds great and the transmission sshifted gears and the wheels were moving. The speedometer worked so then I turned the engine off and lowered the car down from the Jack stands and tired it shine but this time the transmission did not shift gears. I lifted the car back up and did still did not shift gears. The transmission does nothing. The checked the guild level and it's full. What can cause a transmission to suddenly stopped engaging gear?
View 2 Replies
Owning a Hyundai. I have a problem and it seems to be pretty common but haven't gotten anywhere with it yet. Last week my 2004 accent 1.6 manual transmission started running rough. It was idling higher than normal and while driving would not go past a certain rpm (about 2500 if I had to guess,no tach). On the way home from work it was running this way and then started badly misfiring and shut off, when attempted to restart it would not. I pulled the codes with a scanner and got p2400, p0562, and p0121. I charged the battery and replaced the throttle position sensor, still won't start. I can hear the fuel pump kicking on when I turn on the ignition. Also found the ecu 1 fuse blown, replaced it and continued to attempt to start with no luck, fuse was blown again. Like I said I haven't owned the car long and I don't know much about it. I am not sure where to go from here and I don't know how all these symptoms are tied together.
View 42 Replies
That said my wife bought a 2001 Accent 1.6L Auto while I was overseas and it's been a great car, about 8 days ago it just crapped out. The reverse went out on her so we took it to get the codes read and on the way it went in limp mode, started hard shifting between gears and wouldn't go over 45 she says. Took it in to the stealership today and they said that the trans is shot as well as showing codes for P1527, P0732, and P0734. I know what the two slippage codes are and I can prolly just replace the speed sensors and that will be fixed but I'm not sure about the reverse and P1527.
View 4 Replies
Recently bought a `01 Accent 5 speed.. First question . How do I tell if its the 1.5 or 1.6 ? That will really point me in a good start. Ha... Ok.. Check engine light is on and I found a paper in the glove box with some of the codes wrong with it.. The one I focused on was telling me the fuel system was to lean . blah blah blah... Dont remember the exact code as I felt that my research was good and I replaced the MAF sensor... Didnt clear the code...
Also it was sputtering quite a bit in all gears mainly at low rpms. I did change the fuel filter , checked plugs and wires etc.. Now I replaced the MAF sensor and it has not solved the problem.. Took it to have it rescanned and have been given codes p1127 and p0136 .. both seem to relate to the Bank 1 sensor 2 O2 sensor. question is I have saw the "upstream" sensor located right below the exhaust manifold but did not see a second sensor?
From what I have gathered sensor 1 does the most work, so I`m curious if these 2 sensors are interchangeable? Could I buy the downstream sensor and if that does not solve my problem , take it out on try it in the upstream sensor? Also do you really feel as though just changing that sensor will "cure" my sputtering issue? the car only has 88k on it and seems to be in good shape otherwise.. I really need this check engine light problem fixed so I can get inspection..
View 3 Replies
What this may be. 2004 Accent Automatic. We just purchased recently for my daughters fist car. Today when leaving the house the car stays in first gear, you can move the shifter through the gears but it wont shift up. Reverse is fine. Checked the oil level in Neutral when hot and it was ok. Hooked up my code reader and there are no Codes. Car only has 85,000 KM on it.
View 5 Replies
I have the opportunity of getting i believe a 2004 accent gt for next to nothing. It recently lost reverse and all gears aside from first. The codes it is triggering are p0734 p0732 and p0733. Prior to throwing the codes it moved back but wouldn't budge forward. With codes no reverse or any gear higher than first. Car has 160k miles I am pretty mechanical. Should I run from this "cheap" "gas saver" or pick it up? With all 3 codes could it be just that sensor?
View 6 Replies
Just the other day I was driving my car till I've noticed the gears started slipping. At first it was having some issues shifting through the gears (automatic transmission btw). As soon as I got off the highway, I parked in a parking lot just to check underneath the hood. Everything looked fine, went to pull out of the parking lot, no reverse. The gears started to slip up really bad. I noticed that the RPM's kept on reving up and wouldn't go any faster than 20mph. I went to an advance auto parts to get automatic transmission fluid. Still having the same issue and no reverse either. I had to park the car at a location to get it towed back to my house. Some people are saying my transmission is bad, some say it could be a real simple fix. Where to start diagnosing this issue. The car was driving normally until last Monday. My question is where should I start to check and what can I do to see if the transmission is completely shot??
View 33 Replies
I have a 2004 Hyundai Accent 1.6 DOHC 5-speed Manual Transmission ... so here is my problem;
Regardless of whether I am going from a complete stop or if I am simply changing gears the acceleration is practically non-existent, sometimes taking up to 3 minutes to accelerate just 5 mph. While I am driving at a consistent speed of 65 mph, the RPMs will randomly jump from 3000 to 4000 or 5000 with no apparent cause.
I have been told everything from putting air in the tires to replacing the clutch. I do not have the time nor the money to try every option of fixing this issue. I need to attempt to narrow this down to as few probable causes as possible.
View 5 Replies
My 2000 Hyundai Accent, and it has started shifting gears when not traveling at the right speeds to do so.
I'll try to describe it the best I can, When driving I will be going whatever speed limit and all of the sudden it will make a winding noise (like when jumping on highway and pressing hard on gas peddle) and the RPMs will stall. It is like when shifting up, the car drives as normal but then it will shift down and pulls back (making a winding sound)
I am not sure what to do, I was told it seems like it may be the transmission is shot(I had the fluid flushed previously) and that it could cost over $1000 to get it replaced.
View 7 Replies
My 2005 1.6 is losing power now and then when I accelerate. gas mileage is getting worse. I don't want to replace any unnecessary parts. wires and plugs look good.. Codes 300, 301, 302, 303 ..
View 7 Replies
My Mother has an accent 1.3 glx on a 55 plate the problem she has is that every time she accelerates the car does a hiccup (her words not mine) the engine management light comes on and off and then its fine.
View 3 Replies
What is causing the engine to sound like it's not getting enough gas AFTER we turn off the A/C? The two times we have used the A/C, after we push the button to turn it off, the engine sputters like it is going to die ... sounds like it is not getting enough gas. It has over 178,000 miles on it and it sat for about three years before it was given to us.
View 13 Replies
I have a 4.0 6 cyl. Jeep wrangler manual transmission. When the jeep is driven in higher RPM close to redline the jeep sputters a bit (doesn't have full power at or close to redline). Is this a governor or does the jeep have a problem? I do not redline often at all. however i live in the mountains and need to travel up steep pass for 1-2 miles every few months.
View 10 Replies
2000 Hyundai Accent with 180K. Runs and idles smoothly. When sitting for a few minutes at idle I get a waft of smoke when I accelerate. The car burns minimal ammount of oil and the smoke is not apparent while driving.
View 4 Replies