Accent LC (2000-05) :: Code P0326 - Can A Knock Sensor Be Influenced By Heavy Bass?
Jul 5, 2016
I have upgraded my sound system in my car and sometimes i get a P0326 check engine light.
Now i was wondering if its possible that the Heavy bass ( 25/40 Hz, 1200 Watt RMS and 2500 watt Max) Subwoofers could cause the car to vibrate so much that it sets of the knock sensor?
I have read some things about it but i only found that several "Old" cars with OBDII would have this problem? Is that the same on this hyundai accent?
It only comes once in a while after long cruises and bumping.
View 2 Replies
Advertisement
2012 Hyundai Accent. I am getting a po326 code. Wondering if it may be a faulty knock sensor. And po463 fuel level sensor code when I fill up with gas.
View 2 Replies
I have a 2012 hyundai accent. The check engine light came on. The code read knock sensor. Before I could get it into a shop, it went off. It didn't come back for 11 months. When it did come back, the same code was read. Again, it went off the following day before it could be looked at and hasn't been seen since. The shop says that even though there is a history code, it would be hard to diagnose since it isn't an active code. I noticed absolutely no difference in performance when the code was active. Both times it went on, the car was idling for several minutes with the ac on, and it came on as i accelerated onto a highway immediately afterwards. However, it has idled like that many other times without the light coming on as well.
View 11 Replies
Ok had a check engine light. It directed me to replace the IAT sensor.. After some research I found it was integrated into the MAP sensor. Purchased a new sensor and replaced. Drive about 15 miles CEL throws another code. P0106 (sensor i just replaced) faulty Map sensor.
Followed procedure to replace sensor.. unhook battery cable reset ecm. After reset engine is hard to start. Followed by RPM changes (assuming its the ECM re-adjusting). Then CEL flashes 5-6 times and goes out, Drive 15 miles. Map sensor code reappears. (note i only purchased one sensor But repeated install 2 times).
My thought is against wiring. since the codes refer to different signal wires one for IAT one for MAP sensor. Faulty replacement sensor?
2002 Accent 1.6L
View 3 Replies
The MIL light up and I got the P0501 Code. (Speed Sensor. I use a Scangauge II and the Speed is 0 KM/H at any speed. (was working before). But the in dash Speedometer work no problem. I look on the HMAservice web page and did not found where is located the Speed Sensor.
View 9 Replies
About 3 weeks ago, I purchased a 2001 Accent GL 4dr 5spd from a friend of mine. A few days later, the CEL came on. I went to O'Reilly and got the code pulled, it was for a cam sensor input LOW. I replaced the sensor and was on my way.
Yesterday after starting the car for the first time for a few days (I wasn't driving because it needed a clutch), the light came on. Has it gone bad again or is something causing the signal to be low? Maybe a low output on the alternator or low battery? The interior lights dim slightly when the brake pedal is applied while the car is running.
View 8 Replies
So my little car.....driving home from jersey (about an hour and a half) and within the last 2 miles I notice the car just shut off. Not any electronics just the motor. Pulled over and tried to start it an it just cranks prolly no fuel or spark. happened to have my obdII scanner with me. It says camshaft position sensor(po342). Only code in there. Sounds simple enough. Got a new one and put it in. Just cranks. Plugs and wires were done about 3 months ago and I drive about 40 miles a day 5 days a week. I did the timing belt last spring so I opened that back up to make sure the timing hadn't jumped for some stupid reason. It's perfect. Noticed now after doing all of that there is some (a little) oil in the throttle body. I know about blow by and don't think I should have that much at 113k but who knows.
View 2 Replies
My daughter spun her timing belt on her 1.5L accent. when she did, she bent the valve rods and all were replaced. The original code that was thrown was the one in the title. Ordered a new camshaft positioning sensor for the car. Looks a little different than factory. He installed it, and car is still pulling code. He accidentally threw away the original before confirmed that the problem was solved. Why the code is still pulling?? I can tell you this, I can clear the code, start the car and drive without code coming back on. As soon as I shut the vehicle off and restart, engine light comes on. Car runs fine. Had a complete valve job, new timing belt and water pump installed.
View 2 Replies
Like the title says...'02 Accent,1.6 dohc.Won't start.No spark.
Pulled code p0335-crank sensor circuit A.
Replaced sensor...still nothing.
Is there something else that commonly goes with these symptoms?...or did I just get a bum sensor?
Also,once I try starting or turn key on,I hear a buzzing coming from throttle body area for about 10 seconds even after key is off. Not sure if its related or normal.
View 2 Replies
Wife's car threw a p0711 code. It says temp sensor failure or whatever. I found the part on rockauto for 22 bucks but that's not the issue. I've tried searching about this and I seem to find some stuff about elantras and sonatas. I can't seem to find anything specific to a accent. I've read that it's inside the transmission which is fine I've changed valves before and such on old rwd transmissions. But some things I find say it's on the bottom and some say the side. Also wiring is mentioned pretty often with service bulletins.
View 28 Replies
I had a rebuild done on my 2002 Accent. My question is now we get a code for the output shaft speed sensor. Would this have been replaced as part of the transmission rebuild?
View 2 Replies
I need to change the knock sensor of 2011 Accent, don't know where it is.
View 7 Replies
I cannot find the location of the knock sensor in my 2012 Accent. I just replaced the radiator and had everything off up front unobstructed and couldn't find it. Looked in back, sides, but am completely stumped. I have found information on earlier models but not 2012+.
View 37 Replies
I'm looking for the location of the knock sensor I can't find it?
View 4 Replies
Check engine light came ON yesterday and I got a diagnosis at Autozone. These are the codes that came up.
P0456 - EVAP Emission System Leak (very small)
P0326 - Knock Sensor 1 Range/Performance Bank
View 3 Replies
What is the possible, or most likely, cause of a Knock Sensor No 1 Circuit Malfunction reading??
View 1 Replies
So a letter history about the car and this car is a friends car. They owned the car and drove without changing the timing belt when the car hit 109k. So the timing belt snapped and they went out and bought a timing belt and also the timing belt kit with the pulleys and all. They installed it.. didnt turn over or what so ever.
They towed the car to us which we own an auto repair shop. We knew the valves was bent and so we tore off the heads send them off to have them put new valves and etc etc.. We put the car back together for them and now the car runs fine. They pick it up and about a few days later they brought it back due to a check engine. It threw the code:
16711 - Knock sensor 1-G61 Signal too low. (p0327)
now we replaced both knock sensors and when they came and got the car... the check engine light came back one showing the same code. We cleared it out and the next day it came back on showing the same code Again! So now we don't have a clue why that code keeps coming up because we replaced both sensors with a new one. Any clue why the code keeps popping back up?
View 1 Replies
I have a '07 Passat Wagon 2.0T with 80K miles. I just had the carbon scrubbed off the valves (looked like black popcorn stuck in there!) and now I'm getting a "P0327 Knock Sensor 1" light. The motor seems to run just fine (actually much better now without the carbon build-up). I'll clear the code but it will show up again the next day.
What could cause the code? Could it be related to the recent scrubbing (fully removed and replaced the valve cover in the process), perhaps a chunk of carbon floating around in the tubes somewhere? I want to go back to the guys that performed the service but I want to have a good idea of what could be the problem and the fix before I get there.
View 1 Replies
I read at Edmunds that some customers were having problems with the sub woofer causing a rattle whenever they were playing a song with heavy bass. They took it too their dealership and the dealer just told the customer to turn down the base.
That clearly is NOT a fix. It's more of a work around. I was having the same problem with my Azera. As I like my music with heavy base and quite loud, this was becoming quite annoying.
I decided to investigate the problem and discover that the door to the baby seat anchor on the driver side was sitting on the metal underneath the headboard. I got some weather stripping and cut out a couple of 1 inch strips. I then stuffed them under the plastic cooler which surrounds the baby seat achor. My sound system is now clean at any volume level.
If your having a similar problem, open the doors to your baby seat anchors and gently pull up on them. This will pull the head board off the metal underneath. If the rattle goes away, you'll know where to place your weather stripping.
View 3 Replies
The speakers themselves are not rattling, but the door panels themselves are. What kind of cheap material did Toyota use on the Gen 5s to cause door 6x9s rattles on the panel when listening to bass heavy music
View 14 Replies
So, I have my check engine light and the code is p0327 (knock sensor). Clear cose but it returns. Going on for 3 days now. I was suspicious that something else is going on. I also remembered I've been using a little more antifreeze in the reservoir. So, today I needed to watch the coolant. I ran the car for an hr and I found a lot. Red coolant on my belt, the back passenger side of my engine and it was caked on with coolant. I think the water pump is going up.
I was concerned that coolant was also leaking from the intake manifold but it's only the right side, so I'm pretty sure the coolant is being slung around from the belt. I rinsed the engine down and the knock sensor code went away. Temporarily, until more coolant got back there. Do you think I will need to replace the knock sensor along with the water pump or should the sensor work ok after some intense cleaning after the water pump replacement?
View 5 Replies
