Accent LC (2000-05) :: Clicking Noise And Spark On Belts Area
Aug 31, 2012
I have an 05 accent and about 6 months ago I started to notice a clicking sound coming from the belts area ( it sounds exactly like a BBQ grill igniter when it's pressed), the sound starts as soon as I start the car and stays pretty much the whole time, I had the car lifted by my mechanic and he discovered the problem in one of the belts ( not sure what is called but it's the one at the very bottom of the belts, the first one you see when you lift the car ), the spark is seen at the edge of the pulley or where the belt sits on the pulley. The mechanic was puzzled about this, he recommended replacing the crank sensor as a first step, the car runs fine and there is no other symptoms or issues
View 2 Replies
Advertisement
I have 2000 accent 1.5 man trans have had it for 2 years it runs good have done alot of regular maintenance but since i have owned it there was a rattle coming from motor area assumed it was heat shield of some kind, but then i noticed it stops when clutch is engaged or when driving. it is also not there when first started on very cold mornings. wondering if it is a bearing in the clutch area?
View 2 Replies
Noise comes from area of engine by belts and sounds like it might be a bearing. Thought it might just be because this is a timing chain engine. Engine well maintained. Any common issues with these? Difficult to check due to all the moving parts in that area. Read somewhere that water pumps go on these regularly. Not leaking any coolant but I guess it could be the bearing. It is just very difficult to isolate where the noise is coming from.
View 9 Replies
When decelerating and braking, there is a strange clicking noise, and it seems to be coming from the brakes in some way on my 2002 Accent. It does sound like a metal clicking. Steering doesn't affect it, it happens on a corner or on the motorway. The only way to stop it is accelerate. The clicking is faster when the car is going faster, and slower when the car is going slower. The brake pedal isn't vibrating or anything, and I cant actually feel it.
I am certain this is a braking issue as it only started just after I got new brake pads about 2 months ago. It is not transmission related or anything like that. I have had some suggestions about axle's and CV joints but I doubt it's either of those as they are in good condition, and as I said, this started directly after having new brake pads installed!
View 5 Replies
My daughter has bought a 2003 4 door accent and on the way to work she lost most of the brakes. I could not see any fluid leaking and the level was ok. I did try pushing on the brake pedal with my hand and it was making a noise like a clicking? I was thinking it was just the brake light switch but not sure. The place she bought it from put new brakes on it when the driver side was getting really hot. I am thinking maybe air in the system? It sounded like a caliper was sticking when I test drove it but only a couple of times. You would have some brakes but you had to pump the peddle.It is in a parking lot right now but I can work on it unless it is some sort of different? I am going to try to bleed it in a little bit but was thinking I should ask around. I read that the piston could be sticking but can you just rebuild the master cylinder to fix it if that is what it is? I could pull the pedal back a little bit. I only looked at for 4 or 5 minutes kinda dark and no tools with me.
View 10 Replies
Recently, my 04 accent (97,000 miles on engine and auto trans) has started to develop a rattling or Clanking noise coming from the engine at low RPM's. I flushed the engine and changed the oil and oil filter, thinking it could be due to oil clogging the HLA, But this was a no go. The engine is still making the noise, and I think it is starting to get worse.
The noise only happens when the car is idling at low RPM's. As soon as I rev the engine past 1000-1500 RPM's, the noise stops. The noise is worse when idling in gear, either reverse or drive, however as soon as you accelerate past 1000-1500 RPM, the noise goes away, until you decelerate to low RPM again. I'll try to take a video of it and post a link to it on here tomorrow.
View 11 Replies
I have an 2002 Hyundai Auto.
My car has the clicking noise under the following situations:
1) rolling in neutral with/without brake applied
2) rolling/decelerating without gas pedal pressed (I guess the same as rolling in neutral) with/without brake applied
The noise is the most noticeable when going at around 20 to 30mph, and would be gone under very low speed <5-10 mph. The weird thing is when I press the gas pedal and the car is accelerating, the noise is gone too.
My mechanics said it is because the wheel cylinder which is noisy. But I don't quite understand why the noise is gone when the car is accelerating.
View 8 Replies
I used to have a 1999 Mercury Mountaineer 5.0. Loved the truck but sold it because I didn't have a place to store it.
So I bought a 2000 E.B. Explorer! I love it thus far, I was doing a tune-up and now I hate it. I was changing the spark plugs and one of the spark plugs had a lot of rust around it. As I was chipping the rust away so I could get a socket around it coolant started to come out right below the spark plug
I have attached pictures too.
I don't know what this could be. I have done my research, anything from the lower intake manifold gasket to a cracked head. Need info about this type of leak? its no where near any gaskets, I have a friend that says I could have hit a coolant chamber but I wasn't banging hard at all.
View 10 Replies
I'm completely lost. My car won't start. It will turn over but not get a spark. I replaced the plugs and the camshaft position sensor and still having issues. I didn't change the wires when I did the plugs. Would that cause the problem to persist?
View 29 Replies
2005 Accent has been essentially bug free until now.
Drove 3 hours, parked for 4 hours, then when to turn it on... cranked, no turn over. Tried again and the crank died. I figured, ok, no problem, battery getting long in the tooth, time for a new one.
A friend and I were able to push start it (5 speed manual), and yesterday I bought a new battery for it. No worries right?
Wrong. Same thing now. Cranking but no gas/spark/turn over. No check engine light or codes.
My next place I'm guessing I need to check is the fuel pump relay? Should I hear a click a few seconds after I turn the key to on? I believe I should, not sure if my memory is playing tricks on me, but right now there is none.
Relay in the fuse box? Do I need to check anything else first? Have multimeter.
View 4 Replies
So it finally happened...One day she was working just fine and now is dead. OK, starter is working, battery is new but there's absolutely no spark on any of the spark plugs. I wonder what could it be ?
View 8 Replies
My wife's 03 accent cranks over good, but won't start. It does fire some but won't start. I tried squirting starter fluid in the intake and that only made it fire less. Spark is strong on all four cylinders. At first I thought I found the problem because it had weak spark on the middle two cylinders and i replaced that coil pack and now all four are strong, but still same problem.
She drove it home and parked overnight, and in the morning it wouldn't start. I don't think it is the timing belt. I replaced it not too long ago, and I took a peak behind the top of the cover and all still appears to be as it should.
I am now at a bit of a loss. I mean it has good spark, won't start with starting fluid, so what could it be?
View 3 Replies
I own a 2000 accent. Broke down, called racq, they said it was electrical problem with fuel pump and my car would kick over after someone cranks it and another person bangs the underside of the fuel tank a few times(exterior). then broke down again and car wouldn't start at all, had no spark would only crank not kick over, I took it to a mechanic and he found out it was the fuel relay switch so he replaced that and the car was running again, however it was only running on 3 cylinders and the fuel light would flash/turn on for seconds/ flick on and off even with a full tank.
Took it back to the mechanic and he said the fuel lines were blocked and needed new fuel filter so after he fitted all that was still running terrible, would misfire, fuel light still flashed and driving it around drank the fuel. Found out that it was the first cylinder that was the problem. I changed the sparkplugs and no difference
So I went to a car wreckers and replaced the 1st fuel injector (got it for 5 dollars off an accent that was wrote off from the back end) once i fitted the injector it started to run better. It is now running at about 75%. doesnt go as hard as it use to, still misfires, still drinking the fuel and the fuel light is always off and on when I am driving. It has low revs in idle mode so it rattles/shakes heavily as well and smell of fuel in the back seats every now and then.
oh and a side note - drove it a few nights ago and the clutch pedal is 'loose'... as in the grab is near enough clutch in 7/8ths of the way(near the floor) and when the clutch is fully out there is alot of 'play' which is when you press the clutch in a quarter of the way its nothing, no tension or anything just floppy, but im not 100% sure if the clutch cable needs tightening or something worse( i only replaced clutch about 2 months ago so it couldn't be burnt out?)
View 3 Replies
I've got my sister's 1995 Dodge Neon with the 2.0L SOHC. While driving it recently I heard a horrible squeaking noise then a ZZZZZZzzzzzz sound. I immediately pulled over. The check engine light came on, and I shut the car off. Coolant was all over the place leading me to believe the water pump failed. I had it towed to my house, and now I will have it towed to the shop to get fixed. I would like to have them repair the timing belt and water pump. However, I am afraid that the valves were beaten to a pulp and now I will need a new engine. I was only going 35 mph when it happened. What are the odds that my valves were smashed up, and is there anything I can do to check them before I pay for a timing belt/water pump repair?
View 19 Replies
Like the title says...'02 Accent,1.6 dohc.Won't start.No spark.
Pulled code p0335-crank sensor circuit A.
Replaced sensor...still nothing.
Is there something else that commonly goes with these symptoms?...or did I just get a bum sensor?
Also,once I try starting or turn key on,I hear a buzzing coming from throttle body area for about 10 seconds even after key is off. Not sure if its related or normal.
View 2 Replies
I have a hyundai accent 2005 sedan (automatic transmission). The vehicle is a NON-US model. My gas consumption is approximately 7.3km per litre which is very high.
The spark plugs have been replaced , tires are at 30psi , and air filter is new. The spark plug cables are also new. The obdII device does not detect any issues and the engine check light is also off.
View 42 Replies
So I pulled the trigger and got my B5 a little brother... found an awesome 07 4mo wagon sport package with all the bells and whistles with low miles and at a great price. I just couldn't resist. So far I'm loving the car and the extra ~50% hp over the old 30V
I did notice some very noticeable clicking noise in the dash area. It seems to be related to the Climatronic moving flaps around to change air distribution. At random times it starts clicking (kind of a relay sound) a few times in a row and then stops or sometimes it continues clicking in different patterns. When I press the off button on the Climatronic controls it stops immediately.
I'm kinda thinking that it's probably the normal way Climatronic works in this model but it I'm not 100% sure (and the 2001 was silent in that regard) so I want to make sure that it's not something abnormal (like a flap sticking and the sounds I hear is the system trying to flip it a few times before giving up).
Is the clicking normal or should I have the dealer take a look at it? I'll probably take it in soon anyway to get an alignment (car doesn't pull to the side & tires look evenly worn but the steering wheel is about 5 degrees (rough guess) to the right when going straight.
Anything else I need to look out for with this car? It has about 35k miles and all services so far have been done (incl. oil changes every 5k). No open recalls besides a "silent" service action related to the battery cable or something like that (according to the dealer where the car had been services - I called them up before I bought it). There was no major repair work done to the car like the dreaded oil pump bolt issue. Would that even be a concern for an 07 (car was built in Feb 07)?
View 6 Replies
2001.5 Passat 1.8t auto 98k.
It sounds as though I have a relay in the relay panel behind the headlight switch clicking on and off while I am driving. I searched the archives a bit and through my own reasoning, I figured it is not related to the hazard switch or turn signal stock ( I could be wrong though).
Description: It only clicks while I have my foot on the accelerator and the car is in motion, never other wise. It is not dependent on throttle location; it clicks the same way regardless of where the throttle is as long as it's being pressed. The clicking stops completely when the throttle is not being pressed.
Because of this, I am unable to locate the exact relay that is making the noise as it is impossible for me to open the door and look at the relay panel while driving. The clicking is some what erratic; It will click, pause for 2-4seconds click again then wait anywhere from 2 to 10 seconds and repeat. It's driving me nuts. Evap? Is this normal? Can it be stopped?
View 3 Replies
I have been experiencing a crazy problem, my vehicle makes clicking noises from door area, this happens when car is moving or sitting. when i left my car parked for two days the car would not start. My mechanic thinks the door function is acting up and had a remote at one time on this vehicle, for which I don't have now. I just use key to open the door, he will remove door function and clicking should stop. and stop draining battery.
View 1 Replies
My 2005 Accent began making an odd clicking sound about two years ago when I would decrease my speed, not using the brakes. It wasn't loud, just annoying. It went on for some time until my car went into the shop to have the alternator replaced. I explained the noise to the mechanic and they checked it out. They explained they added some type of cleaning fluid somewhere under the hood, and the sound was gone. I was thrilled.
Last year, the sound returned again. Annoyed, I began saving to bring it in to the shop again. In Feb 2013, I had my timing belt and water pump replaced because my mileage of course called for it. The mechanic said he could not hear the clicking sound I was reporting (I really didn't see how.)
Two months later in April, my car decided to die on me and after 5 months I just recently got it up and running again. My differential and transmission were both completely rebuilt. Also, my CV axles have both been replaced. Now that I have my car back, the clicking sound is louder than before and also now happens when I accelerate as well. The faster I go, the faster the clicking gets until it eventually stops. When I slow down, the clicking starts again until I hit my brakes.
I want to take my car and get this noise silenced once and for all since they didn't hear it when my transmission was done last month. What fluid may have been added to what part 2 years ago when this was handled initially?
View 5 Replies
Every time I fill up my gas and put the hands free nozzle switch it clicks every time.
View 5 Replies
