Accent LC (2000-05) :: Check Engine Light Code P0422 / Slight Valve Cover Gasket Leak
Jan 17, 2015
I bought the little car to get off my motorcycle and its done great. But, after a couple trips around town my check engine light came on, and I imiditely noticed a change in my idle and engine performance. Im assuming my engine changed the air/fuel ratio to account for the sensor indications. My initial code read came back with four codes which said something about spark, and O2 sensor, and emissions. I went ahead put new spark plugs, gaped them as well as replaced the first O2 sensor.
After that I reconnected my battery and sure enough no engine light and my idle felt even better than before. (by the way my old plugs looked normal) But shortly down the road the light came on again. My idle did become a little different but not like my first encounter with the engine light. My power too seems a bit degraded, as well as the engine's sound. As of right now I am only reading one code P0422, which I do not see in the manual. I read online that its probably my catalytic converter or my engine is running at an improper air/fuel ratio. I am praying that it is not my catalytic converter and just my engine computer throwing things off.
Other things which may serve as clues:
Slight valve cover gasket leak (I will change the gasket when I do my timing belt job along with other seal and probably the water pump)
When pumping gas I can get about 90 cents in at a time, now more like 40 cents since the Saudis lowered our gas prices. Assuming I've got some kind of venting problem.
Car has 107K manual shift.
View 9 Replies
Advertisement
Got this engine code error, how to proceed?
I have a '00 accent, just purchased a few days ago from a private party, when I bought it, I had a mechanic look it over, gave me the OK and said it passed inspection, no mechanical or obvious running problems with the car.
So I was driving around yesterday and the check engine light came on, took it to get the oil changed because I wasn't sure last time it was done, had the oil changed, light stayed on.
So I took it to auto zone to read the error code, was given this information. How to proceed?
View 1 Replies
Replaced this gasket that seems to be leaking oil. Looks simple enough, is there anything i should do or know before taking on this job? It's a 2002 Accent GS 1.5L ....
View 8 Replies
so I have a 2azfe engine
So there's an oil leak coming from the valve cover gasket (just purchased vehicle dirt cheap with 220k)
found this
Notice all the oil sitting on top of the exhaust mani gasket
In the left(lower) part of the picture it appears to be scraped.
the gasket appears to be newer, I did NOT use a screw driver to remove the valve cover, which is what this appears to have been done..
Can this be sanded down then filled with jb weld, and then regasketed?
View 7 Replies
I've got a coolant leak here (I wiped away some of it before taking the picture):
Close up
This is the only place I can find coolant leaking and it's running down all the way to the water pump:
When I wiped away from just below the valve cover gasket it flaked right off and it doesn't appear there is any oil mixed in. I changed the oil today and it didn't appear to have any coolant mixed in either.
The coolant doesn't appear to have any oil in it's nice and pink as it should be. I started the car from a cold start and sat and watched the area waiting for it to leak but nothing ever came out, of course.
I know there shouldn't be coolant leaking from this area anyways but I don't know how else to explain the trail pictured. I definitely have a small leak somewhere as I've found coolant on the floor of the garage before.
Do I just replace the valve cover gasket and move on or is there something else I should be concerned with here?
View 11 Replies
I had a very slow oil leak that dripped onto the garage floor and i brought it into the dealership. They said it was a leaking left valve cover gasket; I searched and came up with nothing? The engine has just over 30K miles on it.
View 20 Replies
I just noticed what appeared to be an oil leak around the valve cover gasket, which the VW dealer has determined to be a defective cam sensor. Apparently the VW parts distribution center in Wisconsin has 530 of these in stock, so it may be a common failure. This is on a 2010 GTI with 28,xxx miles. Thought the community would like to know.
View 2 Replies
I am having accent 2003, 1.5L. It starts fine ,... runs fine.. but it consume engine oil. I have change 3 times in a year. i just noticed a little bit of smoke from where the spark plugs and the valve gasket is. There is no drop of oil on the ground.
I can see few oil on near the area of spark plugs and valve cover panel. There is no smoke from the exhaust too. It starts fine. Does that need replacement of valve gasket or head gasket ?
View 1 Replies
So, when I bought my truck, it leaked oil.....bad. It goes through around 2-3 quarts a week. I needed a vehicle, this one was cheap, so...I run it. Every other day, I put half a tank of gas and a couple quarts of oil in it. It leaks on the passenger side, right above the starter. I figured it was the valve cover gasket, and planned on changing it today. I saw a post about the "typical" head gasket oil leak, which sound suspiciously like what mine is doing. I have no oil in the coolant,or vice-versa.....
View 9 Replies
Looking for some insight into the state of the motor in a 2002 XD. Short story is that it appears to be leaking oil from the valve cover gasket (common, I know) and sometimes winds up running extremely low on oil before it gets changed. When draining the minimal oil in these conditions, non insignificant amounts of water can be found along with the drained oil.
Car is at 155k miles, has exhibited this behavior for more than a year, and has no noticeable knocking issues, power loss, mpg loss, heating/cooling issues, or any other ill effects other than apparently making a mess in the engine bay, on the ground where it parks, and scaring people when draining the oil.
Logically this is going to not be the case forever.... Thoughts? Prognosis? Treatment?
View 7 Replies
I'm suspecting a small valve cover gasket leak. I've noticed dirt starting to accumulate near the alternator side of the front valve cover, there is dirt on there stuck to oil, I don't see any wet oil but its so minor the dirt just sticks to it. 107k miles here. Seems to be a common problem. I think Downhiller had a large oil leak, source unknown around his crank pulley area. You wouldn't think a car this young would leak oil. It's not bad, I havn't had to top any off I just like a mildly clean engine.
View 38 Replies
I recently purchased an 06 f150 fx4 5.4L with 60K miles. Just recently my check engine light came on and I've noticed a slight rough idle in park. I took it to autozone and the code read P0422 evap emission leak. Bought a new fuel cap but didn't work... EGR valve?
View 2 Replies
I have a a 02 jetta 1.8 turbo the code po343 came up after new temp sensor,valve cover gasket and full tune up. is it an easy fix the car is misfiring an very hard starting.
View 1 Replies
My sister-in-law just came home with a P2069 code. I can't seem to understand how to use the search feature here, every time I enter the spam code its invalid even when I am entering it correct...
View 8 Replies
My 2000 Hyundai Accent Hatchback (manual) is tripping the code P0422 (Main Catalyst Efficiency Below Threshold (Bank 1)). If i clear the code it will pop back up after about 40-60 miles of driving. I hooked my OBDII sensor to it and look at the voltage output from the two O2 sensors and the front one oscillates between .2 to .7V and the downstream one does as well switching about at the rate. From my understanding the downstream O2 sensor should stay fairly steady or at least switch much slower than the upstream one. I get pretty good gas mileage, typ. ~30mpg. Luckily my state does not have emission testing. Is it actually the catalytic converter, the downstream O2 sensor or something else?
View 10 Replies
while scraping ice off the windshield this morning with the car warming up, it started to choke, engine light came on. Used my OBD reader and found only one code, that being p0740. Cleared the code and all was fine after that, it drives the same way it always has and nothing feels different, revs are the same shifts gears the same. I know it had something to do with the torque converter clutch.
View 4 Replies
I have a 99 Tiburon 2.0 DOHC that I cant seem to get through emissions. The code, p0422 main catalyst efficiency below threshold bank 1 keeps popping up even after replacing the cat converter (twice) and replacing both 02 sensors. What else could be triggering this code and how to fix it?
View 2 Replies
New valve cover gasket on my 03 VR6 GTI, new plugs, oil filter and cooler seals, new gaskets on the intake manifold and when we started it up . . . .
[URL] .....
It runs rough.
EPC light is on.
Stall at idle.
Runs great at full throttle.
View 3 Replies
My mk4 sat for a while and upon starting up was misfiring. I checked for pvc leaks and didn't see anything but went ahead and cleaned my maf sensor and decided to pull my coils. Cylinder 1 had oil on the tip and around the spark plug which to me spelled out a bad valve cover gasket. I got all the parts to do the inner and outer gaskets and replace the coil and spark plug, however we got a snowstorm and my luck a rabbit got in and ate the wiring on one of my fuel injector connectors.
So went ahead and put on the new gasket, replaced the coil and plug and bought a new Fuel Injector Connector and spliced in onto the Injector "Pigtail'. I double checked everything was reattached properly and let the gasket sealant dry for 24 hours. I went to start it tonight and after trying to turnover it completely cuts out, wont even start up. I'm extremely frustrated at this point and am thinking the rabbit must have gotten to something else unless I did something wrong in the process of repairing.
View 3 Replies
Mystery issue with my 2001 Accent GSI (5-speed manual, 1.6 L). I'm getting a P0300 error code and the Check Engine light (the light is like an old friend, I miss it when it's not on). This happened four months ago and I replaced the ignition coil - seemed to fix things - but now the light and the error is back with a vengeance. Car stumbles and runs rough. Changed the plugs and plug wires, but no difference.
BTW, there's a small pin hole in the upper part of the gas tank (just enough to give it a gassy smell when the tank is full) but I don't think the hole would be big enough at this stage to cause the check engine light to come on in the same way it does if you leave the gas cap off or loose.
View 3 Replies
This is the infamous error code many Accent owners might have experienced it. The code refers to "Too lean intake system". People try to replace all kinds of parts like ECM, MAF, O2 Sensor, TPS, Fuel Pump, Fuel Filter, etc. according to my research. I just bought a 2001 Accent and the P2188 light came on. I wrote an email to Hyundai Corp. Asking what would be the most likely part that will cause the (P2188) check engine light to come on.
View 3 Replies
