Accent LC (2000-05) :: 2003 - Intermittent Rough Idle After Warm Up
Jun 8, 2013
This is what my car is doing after it warms up. It will do it then stop, then do it again and so on. I am pretty sure when the motor is under load it runs a little rough but is hard to tell. The car has 178,000 miles on it. timing belt was done at 113,000. I just replace the plugs and wires changed the oil and the air filter 1,000 miles ago. and it will still do it. I am at a loss as to why it keeps doing this. I have tried injector cleaner, sea foam and engine restore. What would cause this? The check engine light is not on. i replaced the crankshaft positioning sensor about 40,000 miles ago.
Its a 2003 hatch with the 1.6 5 speed .....
View 8 Replies
Advertisement
I have a 05 fx4 5.4L with 85k on it. It has started idling rough when i come to a stop light or slow down to 10 mph or less. It only does it once in a while. There doesn't seem to be any real pattern. The motor shakes until you rev it up and then it goes away.
I have cleaned the maf, put in new air filter and fuel filter. And put in a new battery. Would a coil act like that? Maybe plugs? Or a vacuum leak?
View 14 Replies
Still showing the same codes (per repairman) and still having the intermittent rough idle at low speeds when the engine is warm. It has been so intermittent that I could almost live with it.
So repair guys first replaces the VCT's and runs fine until warmed up and the problem reoccurs with the same codes. He replaces both cam phasers and tensioners today and still same problem and same codes which point to the VCT and cam phasers.
Truck has 80k, city driven, oil changed every 3k or so. Burns ethanol and still runs great at speeds over 10 mph even when this problem appears.
View 9 Replies
I have a 2000 LC that has a few symptoms - intermittent misfire/running rough at these times it has:
dark smoke
uses 3 times the fuel
loss of power (to normal)
will pick up revs slow without running rough and runs normal at high revs.
dies misses and then picks up revs slowly when accelerator is pushed fast to the floor from idle.
Hyundai mechanics checked computer and it coded change spark plug leads this did not fix the problem, and have no idea.
About 6 months ago the car was doing the intermittent thing when it died and liquid was heard splashing on the ground. I found the main petrol line connecting to the pump had come completely off. After replacing all problems ceased and the car ran perfect with full power etc.
I've checked the fuel lines none appear to be leaking etc.
View 12 Replies
I have a 2000 Accent with about 150,000 miles on it. Recently I have noticed that when my car is sitting in an intersection, the car appears to idle roughly. I would't exactly say that the car is idling rough, cause it stays at a consistent RPM while in drive or park, but the engine gets louder and the steering wheel starts to vibrating. When I slightly step on the gas, the vibration goes away. Also, when I put my car in park or neutral, the car quiets down and the vibrating stops.
I was wondering if it could be the throttle position sensor, or maybe a broken motor mount, but I haven't had a chance to look into it it. I did replace the purge control valve last week, which slightly improved the vibrations.
View 14 Replies
We are at 120K miles. The vehicle runs fine most of the time, but every once in 10-15 starts, it will rough idle or stall after a short warm up time when my wife stops at an intersection. Once she restarts it, it runs fine.
I have changed the spark plugs and wires, the fuel pump, the crankshaft position sensor (was fried) and after consulting this forum, I checked the fuel pressure regulator and the diaphragm is not leaking.
I was able to recreate the rough idle and the CEL on the dash, but my two OBDII readers said there were no codes And the bluetooth reader I am using is indicating that the following tests are not completing: Fuel System, Catalyst, Evaporative System and Oxygen Senors.
The dash CEL resets itself upon restart and does not light until the symptoms return.
After reading the Haynes Repair Manual, I am wondering about the Evaporative Emissions Control (EVAP) system? But I don't want to lead the troubleshooting.
We bought the vehicle at 60K miles and it has been mostly reliable.
View 26 Replies
I'm an Accent 2000 gs owner and since a few days i had this problem. It has a bad idle and looks like it will stall... need to give some gas to stay alive.
Bad acceleration too, it misses some gas. (puffing, rumbling, shaking a bit). After accel, it's ok until the next red light.
Now I can't even drive cause it's worse. (too difficult to accelerate). Is it a sensor?
View 8 Replies
Symptoms:
- Check engine light: misfire on all cylinders, and "lean fuel trim at part throttle".
Started with changing leads and plugs without improvement. Then I found the tank ventilation seemed to be clogged, as there was a massive vacuum when opening the filler cap. Checked the canister and replaced a couple of corroded lines. Also used compressed air to blow through the canister and lines up to the Evap-purge valve. Seemed to be OK afterwards (no vacuum), but still misfires.
Changed the Mass Air flow sensor, and it seems the misfires got better, but instead I have some other issues:
- Hard to start when cold. Starts up fine for a second then sounds like it's getting to much fuel and dies. Possible to keep it running if pumping the pedal or holding it at higher revs.
- Rough idle when warm. (Same as before I changed the MAF and plugs/ leads.)
- Drives and runs ok when out on the road.
- Pulled the cable to the Idle Control Valve without any change in idle...?
- Got flashing engine light and "misfire cylinder 4" when giving full throttle on low revs and seond gear up a steep climb.
What could cause this?
- Temperature sensor?
- O2-sensor?
- Idle control valve?
- Coilpack?
View 26 Replies
I have a Hyundai-Accent 1.5 GL, Auto, year 2000 car. I bought this 4 months ago and ever since it has been giving the check engine signal. However, running conditions of the car has been normal and therefore, I didn't worry about the check engine signal. Now, the engine is rough idling for few seconds when I start the car in the morning, and then it comes back to normal.
View 12 Replies
I've recently purchased an 01 accent GS and I've replaced the timing belt, water pump, and spark plugs. Ive also got no cold air, and original struts with 119k on the vehicle. Those are the least of my worries now as my car loves quitting out at idle; and it does not get any better hot or cold. One of the plugs was completely black when it was taken out (not by me: mechanic work) so that's when they mentioned a cylinder misfire. they wanted an additional 100 to figure out what that could be attributed to on top of the 550 for the work mentioned above! I am now next to broke and want to see if I can trouble shoot some of the causes myself. I am thinking Plug wires, crankshaft/camshaft position sensors (if there are 2 dif ones?) MAF sensor, o2 sensor, injectors, and fuel filter. My understanding is that the coil pack controls 2 cylinders at a time and I just have 1 bad cylinder...I need to figure out where to start as I have no codes to work off of. also, I don't know how to assess resistance with an ohm meter.
View 12 Replies
I have a 00 Accent with 132k miles, I replaced the motor a year ago with a correct 2000 Hyundai 1.5 with 50k miles. I replaced everything that I could at the time, timing belt , starter, water pump, and clutch. It has been running fantastic getting 40 miles per gallon with zero problems , However in the last week I have noticed a rough idle that seems to miss with a vibration that it didn't have before. I have a noticeable loss of power and torque. My miles per gallon has also dropped to about 25 mpg. My check engine light is not on. I will check the plugs and change the air filter today but I would like to know what else could be causing the problem as I am not really sure what to check.
View 9 Replies
Recently bought a 2001 Accent that has been experiencing a 'rough idle' for the last few weeks. Basically, after I've driven the car for a few minutes (from a cold engine position) and then stop at a stop light or stop sign, I can hear the engine get louder and the car starts to vibrate slightly, after I've driven for about 15 minutes at higher speeds and then stop again I can actually see the steering wheel shaking when I take my hands off of it. If i put the car in park when I am stopped and the engine is on, the idle calms down quite a bit. The weird part is that when I first start driving the car in the morning, the rough idle problem doesn't happen until about 5 minutes of steady driving - so when the engine is colder I don't experience the problem, The problem is not that serious, and Ive already brought it into a dealer who cleaned out fuel injection, gave me a major tune up and replaced all the spark plugs, but the problem still persists. I am gonna bring it back to them but they seem a bit lost to be honest. Other than this the car is driving normally when I am not idling.
View 14 Replies
i recently changed my engine oil and filter from carquest brand to quaker state and about 500 miles later, i started having some issues like, rough idle and loud ticking and bottom engine noise. is that just a coincidence or any problems with this oil? 1.6L D.O.H.C.
View 2 Replies
2003 Ford Explorer 4.6 liter AWD. Having some kind of VERY STUBBORN idle / emission problem. When it started it was an intermittent rough idle, mostly going too low or making a periodic "drumming" sound that could be felt and heard at the air cleaner box. CHeck engine codes were PO 442 evap system leak. I first cleaned and inspected throttle body, mass air flow sensor and idle air control valve. I inspected hoses for leaks, including spraying cleaner to see if I could detect idle changes / leaks. I then replaced Idle Air Control Valve. Did not seem to cure problem . SO took it into Ford Dealership and they smoke tested and said needed Vapor Management Valve and Vent Solenoid. I replaced VMV myself. Idle no longer "rattled" but when driving and braking the idle would drop down very low and sometimes not "kick up" and would die. I then took it back to dealership to have them replace the vent solenoid and reprogram the PCM. Still doing it. They said I might have a defective (new) Idle air control and to replace it- otherwise they dont have a clue.
View 2 Replies
2004 Accent 1.6L
Changed the timing belt and water pump this past weekend. I made sure the timing marks aligned before I put the belts on. They were still aligned after turning the engine by hand and still aligned after taking the car out for a test drive. I did not notice rough idle when I started the engine in the garage nor did I notice a rough idle during the test drive.
A few days later I am now noticing the car will idle roughly when I come to a stop. The idle will get rough enough to gently shake the car. No engine light and no unusual noise from the engine.
I am going to check the timing marks again tonight. I suspect the belt may actually be off by one tooth. I have driven over 100 miles since changing the belt so I don't believe it is off anymore than one tooth or else I presume I'd probably have already broken down or been hearing unusual noises.
Furthermore, I do not seem to have any loss in power. I still have good acceleration and no roughness unless at idle engine speed. I do, however, run rough at higher speeds (75+ mph) on the highway, but this was present before the timing belt change. Unfortunately the car does not have an RPM gauge.
Having said all of this, are there any other possible reasons why I might be idling rough now?
View 4 Replies
For the last couple months I've been messing with a P1118 code. Started a few months ago when I noticed my fuel mileage was down 1-2MPG. Also sometimes a rough seeming idle (hard to tell with the diesel). Then it threw a P1118, so I replaced the temp sensor under the turbo. The code went away for a while then came back, fuel mileage didn't change. So I replaced the temp sensor in the air filter box.
The code went away AND my fuel mileage seems to have come back to normal. Now, code thrown again. Search on P1118 hasn't been super useful. Seems like replacing the sensor under the turbo is the trick. Also seems to come up in combination with a bunch of other codes with battery problems. I suppose it's possible I have some sort of electrical gremlin. It throws the code on startup and stays on until I shut it off. Doesn't come on every time, is off more often than on.
View 2 Replies
I have a 2003 santa fe I just replaced the cat. in it because it was running so poorly. Now that I've replaced the cat it seems to be worse. The car idles real rough, and cant get it to go over 2000 rpms. No engine light. Had the codes checked and all came out fine. I pulled out the plugs and replaced with new. The car in park ran great until I put it in gear then went back to the same no power, rough idle and cant get more than 2000rpm with out a stall. Stalls but dose not die. Disconnected the pre o2 sensor no change.
View 2 Replies
2000 Ford F150 1/2 ton 2x 5.4L... Last year, I started having a problem where when the temp dropped below 50 degrees outside, my F150 would idle really rough and sometimes stall out. The CEL came on and reported some codes that I don't remember but pointed to bad air/fuel mix. I consulted a friend and he suggested changing out the IAC. I did that just towards the end of the cold weather spell we were having and the engine ran great so I assumed it was fixed.
Well, the temps have been below 50 for 8 days now and ever since the temps dropped the problem has come back. I took it to AutoZone to have the codes read and they gave me the following:
P1151 - Lack of O2 switches -bank 2 sensor 1 : ECM could not adjust fuel trim because of a lean or rich condition
AND
P0171 - Fuel trim bank one condition : The powertrain control module uses the oxygen sensor to calculate the Air/Fuel ratio of the engine. The computer recognized a rich or lean condition on one engine bank only.
Both printouts that they gave me mentioned the following:
Poor fuel pressure
Bad or Malfunctioning MAF sensor - Dirty/defective
Oxygen sensor defective
Fuel injector problem - Leaking or fuel pressure high/low
Vacuum leak on engine
I again called my mechanic friend and he suggested cleaning the MAF and if that didn't work replacing the MAF. I cleaned it and the problem was better but still not fixed.
View 3 Replies
I have a 2010 corolla with 32k miles, automatic transmission. I have an intermittent low idle issue when it rained or when it is below freezing 32F. It happens when I am in drive and about to brake to a complete stop. The idle dips to around 500 rpm, the engine shudders and the car shakes then after a second or two, the engine idle goes back up to 800 rpm. There is no engine concerns at any other speed just at idle. I have no CEL codes. The engine never stalls. Low idle when braking.
View 1 Replies
Engine is a 69 390, fresh rebuild by the PO... Aluminum intake manifold and new Edelbrock 4bbl Drop in Crane ignition.
Runs great... Except when its warm out, or even on cold days when its warmed up after a substantial drive..
AT that point here is what happens: No issue until I shut it off then it diesels badly, THEN.. When I restart it will not idle, dies.. If I keep my foot on the accelerator it will keep running, but not well.. If I let it run for a good while, 5-10 mins, it smooths out... Consistently acts like this .. Again.. Not when the engine is cold, and not on a cold day until it really warms up..
I suspected a vacuum leak? Replaced any suspicious vac tubing.. Cant get to the AT modulator easily, have not checked it yet?? Also suspect the intake manifold??
View 19 Replies
My car is standard 5 speed transmission, when my car is running my idle varys between 800ish to 1500 intermittently within seconds and if I don't drive it after starting the car it will stall on me (in neutral) after the rpms go up and down about 9 times.
The thing I found is if I disconnect my idle air control valve attached to my throttle body it stops the jumps in rpm. I have tried replacing the valve with one of my friends control valve Hyundai accent 2004 that works and fits perfectly on his doesn't work on mine. Right now I have my idle air control valve disconnected at the moment but i want to fix this issue because my rpms are at 1300 at idle.
View 7 Replies
