Accent LC (2000-05) :: 2002 - Jerking / Stalling While In First And Second Gears If Accelerate Too Quickly
Mar 19, 2009
My standard 2002 accent is undriveable and at the mechanic right now (100,000km). For the past few weeks the car has driven very jerky. While in first and second gears if i accelerate too quickly it just jerks/slips and has very little power.
Yesterday the check engine light came on and i got codes P0300, P0302, P0303...misfire in cylinders 2 and 3. Checked this forum and decided to buy new spark plugs (last replaced plugs and wires 1.5 years ago). Got into the car and could go more than a block because it was jerking and then kept stalling. Replaced the sparkplugs and nothing changed. Had it towed to the mechanic...after a few hours he said he had cleaned the exhaust manifold and it was driving fine. I picked it up and a block away it stalled again.
The mechanic now says 3 of my fuel injectors need to be replaced and the fourth will probably go soon and it will be about $700 to fix. Does this sound right for these codes?
I called hyundai parts and they told me each injector is $236...he also told me he doubted they had to be replaced cause he has never seen an accent have fuel injectors replaced and also they rarely sell these injectors, he said it was probably something electrical.
I have found 4 injectors on ebay for $200 but is this really the problem? The mechanic says it is 100% the problem. But from reading the forum I dont think so.
Also wanted to add that i often noticed the smell of burning plastic. Smoke seems to be coming from spark plug area when i notice the smell but nothing looks burnt/melted.
View 14 Replies
Advertisement
I own a hyundai accent 2000 GLS, i have recently replaced the ECM wiring and a brand new ignition coil, however the engine still sputters when i try to accelerate in higher gears, my mechanic told me that the engine mounting bushes need replacement. is it one of the causes? the sparks plugs are new, fuel pump is working fine.
View 7 Replies
07 accent with transmission lurching.
As the auto trans heats up, the gears begin to get sticky. This creates a jerking motion as the engine downshifts while braking. It also happens at high speeds when attempting to downshift for acceleration.
Additionally, while shifting from park at hot temperatures, the transmission will take up to 15 seconds to engage into drive, and even more time (30-40 sec) to shift into reverse.
The car has recently (approx 6-8000 miles ago) had a complete transmission flush. The auto shop in town also suggested and did replace a sensor somewhere which supposedly had gone bad. But the problem persists...
View 2 Replies
2002 Jetta 2.0.... car was jerking when accelerating and check engine light was flashing, severe loss of power and when stopped at lights it would shake and the rpms would drop and go back up... took it in and was told to get the coil pack replaced. One week later new coil pack - check engine light is back on and yesterday same problem (car was idling rough, and severe jerking/flashing check engine light happened again). Took it to autozone to read the code it is giving P0420.... The shop said i might need new plugs and wires, which were replaced with bosch parts one year ago. Any chances these went bad so quickly?
View 3 Replies
My 2004 1.6 L accent does the following, no matter how much gasoline is or is not in the tank: Whenever I remove and replace the gas cap [which is brand new], as i drive away, the engine light flashes quickly about 20-25 times; rests for about 15 seconds and flashes again about 20-25 times. Thereafter it goes out for the rest of the drive. while it is flashing, the car idles roughly. This happens even if i only remove the cap to add some water absorbent or some injector cleaner. it also happens when i fill up the tank. by the way, i NEVER TOP UP. I always quit filling with gasoline when the pump goes "thunk." this has me completely stumped.
View 9 Replies
I have an Hyundai Accent Petrol 1.6L ABS.
While driving the other day suddenly the car started sputtering or jerking while on low rpm and after changing gears
the exhaust is also making sputtering sounds when on idle.
when I press the accelerator the sputters/jerks and then picks up rpm. the performance of the car does not seem to be affected but petrol mileage has fallen.
when I accelerate slowly then the sputtering/jerking is reduced and sometimes not present much. There is also a deep and heavy sound of the engine running heard inside the car (which has been present before the timing belt change)
I took the car to the workshop and attached the OBD.
the codes P0340 P0112 were present. we now erased the codes and the mechanic checked the sensor wire plugs for the cam sensor and air sensor saying it looks fine. on attaching the OBD again the codes were not present. However the sputtering/jerking continues. (the fuel pump and filter were also checked to be ok)
My Timing belt has been changed approximately a month back. My car does not run much (Approx 40kms a day)
My questions are
1. can a bad timing of the timing belt have anything to do with this and thus giving these codes?
2. Can there be something wrong with the exhaust due to which this problem is taking place?
3. what could be possibly wrong with the car?
4. Can this result in any damage to the engine?
View 13 Replies
My hyundai accent 2005, have problem of jerks /die speed after engine get warm, also increase if AC on, when I starts car in morning it works great and no problem but after 3 or 5 km as engine get hotter speed kills,but it happens more or worst in evening at 4 when returning from office and temp is 45+ in riyadh, saudiarabia.
I change air filter, fuel filter, spark plugs, spark cables, also use fuel injector cleaner but still problem remains, I want to tell you its start when I changed engine valve cover gasket due to oil leak, as I changed this problem suddenly appeared, I went to other mechanic but he told me the problem not in valve cover gasket,it is somewhere else he clean my throttle body ,and its works for 2 day only that i felt the problem solved but after two days problem appeared again,there is no engine light power on for any electronic malfunctioning.
View 15 Replies
own a 2005 Hyundai accent 1.6L engine. I replace the engine today. The previous engine had internal damage. The transmission I left alone. I didn't disconnect the wiring. I only removed the engine. The transmission worked flawless. When I turned on the car the engine sounds great and the transmission sshifted gears and the wheels were moving. The speedometer worked so then I turned the engine off and lowered the car down from the Jack stands and tired it shine but this time the transmission did not shift gears. I lifted the car back up and did still did not shift gears. The transmission does nothing. The checked the guild level and it's full. What can cause a transmission to suddenly stopped engaging gear?
View 2 Replies
That said my wife bought a 2001 Accent 1.6L Auto while I was overseas and it's been a great car, about 8 days ago it just crapped out. The reverse went out on her so we took it to get the codes read and on the way it went in limp mode, started hard shifting between gears and wouldn't go over 45 she says. Took it in to the stealership today and they said that the trans is shot as well as showing codes for P1527, P0732, and P0734. I know what the two slippage codes are and I can prolly just replace the speed sensors and that will be fixed but I'm not sure about the reverse and P1527.
View 4 Replies
Recently bought a `01 Accent 5 speed.. First question . How do I tell if its the 1.5 or 1.6 ? That will really point me in a good start. Ha... Ok.. Check engine light is on and I found a paper in the glove box with some of the codes wrong with it.. The one I focused on was telling me the fuel system was to lean . blah blah blah... Dont remember the exact code as I felt that my research was good and I replaced the MAF sensor... Didnt clear the code...
Also it was sputtering quite a bit in all gears mainly at low rpms. I did change the fuel filter , checked plugs and wires etc.. Now I replaced the MAF sensor and it has not solved the problem.. Took it to have it rescanned and have been given codes p1127 and p0136 .. both seem to relate to the Bank 1 sensor 2 O2 sensor. question is I have saw the "upstream" sensor located right below the exhaust manifold but did not see a second sensor?
From what I have gathered sensor 1 does the most work, so I`m curious if these 2 sensors are interchangeable? Could I buy the downstream sensor and if that does not solve my problem , take it out on try it in the upstream sensor? Also do you really feel as though just changing that sensor will "cure" my sputtering issue? the car only has 88k on it and seems to be in good shape otherwise.. I really need this check engine light problem fixed so I can get inspection..
View 3 Replies
What this may be. 2004 Accent Automatic. We just purchased recently for my daughters fist car. Today when leaving the house the car stays in first gear, you can move the shifter through the gears but it wont shift up. Reverse is fine. Checked the oil level in Neutral when hot and it was ok. Hooked up my code reader and there are no Codes. Car only has 85,000 KM on it.
View 5 Replies
I have the opportunity of getting i believe a 2004 accent gt for next to nothing. It recently lost reverse and all gears aside from first. The codes it is triggering are p0734 p0732 and p0733. Prior to throwing the codes it moved back but wouldn't budge forward. With codes no reverse or any gear higher than first. Car has 160k miles I am pretty mechanical. Should I run from this "cheap" "gas saver" or pick it up? With all 3 codes could it be just that sensor?
View 6 Replies
Just the other day I was driving my car till I've noticed the gears started slipping. At first it was having some issues shifting through the gears (automatic transmission btw). As soon as I got off the highway, I parked in a parking lot just to check underneath the hood. Everything looked fine, went to pull out of the parking lot, no reverse. The gears started to slip up really bad. I noticed that the RPM's kept on reving up and wouldn't go any faster than 20mph. I went to an advance auto parts to get automatic transmission fluid. Still having the same issue and no reverse either. I had to park the car at a location to get it towed back to my house. Some people are saying my transmission is bad, some say it could be a real simple fix. Where to start diagnosing this issue. The car was driving normally until last Monday. My question is where should I start to check and what can I do to see if the transmission is completely shot??
View 33 Replies
I have a 2004 Hyundai Accent 1.6 DOHC 5-speed Manual Transmission ... so here is my problem;
Regardless of whether I am going from a complete stop or if I am simply changing gears the acceleration is practically non-existent, sometimes taking up to 3 minutes to accelerate just 5 mph. While I am driving at a consistent speed of 65 mph, the RPMs will randomly jump from 3000 to 4000 or 5000 with no apparent cause.
I have been told everything from putting air in the tires to replacing the clutch. I do not have the time nor the money to try every option of fixing this issue. I need to attempt to narrow this down to as few probable causes as possible.
View 5 Replies
My 2000 Hyundai Accent, and it has started shifting gears when not traveling at the right speeds to do so.
I'll try to describe it the best I can, When driving I will be going whatever speed limit and all of the sudden it will make a winding noise (like when jumping on highway and pressing hard on gas peddle) and the RPMs will stall. It is like when shifting up, the car drives as normal but then it will shift down and pulls back (making a winding sound)
I am not sure what to do, I was told it seems like it may be the transmission is shot(I had the fluid flushed previously) and that it could cost over $1000 to get it replaced.
View 7 Replies
I'm having a problem with my mom's 2005 Accent. It starts up just fine when cold, and will run for 15-20 minutes just fine, sometimes longer. Then, usually as you're slowing down, the engine just turns off. No bogging, no sputter, just turns off as if someone turned the key. Sometimes it will start back right back up, more often, it will need to sit for 30 seconds to a minute, and then it will fire back up. After that, all bets are off. Sometimes it will run again for 10-15 minutes, sometimes it will idle rough and die. I'm leaning towards a coil pack, but I'm sick of throwing parts at this. The last time I got it to idle roughly, it threw a random misfire, and cylinder 1, 2, and 4 misfire codes. I've changed out (in rough order) MAP sensor, the fuel pump (no fuel filter in this model), TPS (threw code for this), spark plugs, and most recently the Crankshaft Position Sensor. I'm not sure how to test the coil packs.
View 5 Replies
This just started over the weekend. It's stalling. It does it mostly when I let off the gas and start slowing down. If I give it gas, it seems to straighten out for a minute. It has done this a couple of times while driving also. It sounds as if the engine speeds up and then slows down and stalls. The check engine light is on also. It went out yesterday and then popped back on today.
View 2 Replies
My 2005 1.6 is losing power now and then when I accelerate. gas mileage is getting worse. I don't want to replace any unnecessary parts. wires and plugs look good.. Codes 300, 301, 302, 303 ..
View 7 Replies
My Mother has an accent 1.3 glx on a 55 plate the problem she has is that every time she accelerates the car does a hiccup (her words not mine) the engine management light comes on and off and then its fine.
View 3 Replies
I inherited this car from my grandmother when she passed. It has low miles, around 40k. Since I paid zero for it, I would like to keep it. Historically I have done all my repairs, but never trans work.
Here are the symptoms. The car has issues shifting into higher gears. I have to punch the gas and then it will switch gears. It then began to do this for reverse, and now now reverse does not work at all.
At first I thought it was a speed sensor problem, but when I took it in to be read, it came up with P0734. It could be electrical (Speed sensor?), low fluid (it's not low), or 4th gear.
Is this transmission worth me fixing or paying to have it repaired, or should I move on?
P.S. If I drop the pan and find shavings, I understand that to point to 4th gear and bearing (also what the computer code read as the issue). Do shavings mean it definitely is 4th/bearing, or could it be another blown part?
View 4 Replies
Last week I started having problems with my 05 Accent, hatchback, 1.6L engine, automatic transmission. Filled the tank up with gas and the car stalled pulling out of the station and wouldn't start unless I pumped the gas while cranking the engine. Ran and started fine after that and I thought it may have just been an air bubble in the fuel line, since there wasn't a check engine light or any other symptoms after that. Fast forward to this morning and the check engine light comes on during my commute and when I checked it, it gave an EVAP code (P0441). I also stopped to refill the gas and it stalled again as I was leaving the station. Also after I measured the gas mileage I found that I'd lost around 7 mpg (from around 30 to around 23).
I've never heard of EVAP problems causing stalling and loss of gas mileage but I'm not all that familiar with these systems so I don't really know. I'm going to test if it's the gas cap going bad since on the list of things that could cause a P0441 that seems to be the easiest place to start, but other than that where to start looking?
View 8 Replies
