Accent LC (2000-05) :: 2001 - Running Rough After Filling Up
Mar 18, 2015
A few weeks ago my car was running perfectly fine, i filled it up with fuel and then it started running a bit rough. Would drive ok but could feel it surging and if i backed off on the accelerator it would try stall.Also the fumes in the car were a lot stronger than usual. Got home and it stalled, started it up and was idling rough and blowing black smoke :/ no engine light has come on though. I did the typical thing and googled possibilities, the mojority said that it was the purge control valve so i replaced that with a new elantra one (part numbers were the same) and its still running rough We are now thinking it could be the oxygen sensor? Have checked vacuum lines and stuff for air leaks and cant find any. Unplugged the oxygen sensor while car was running and it made no difference at all.. If the oxygen sensor was working properly it would of affected how the car was running, right?
View 1 Replies
Advertisement
I have a 2000 hyundai accent and when i fill with fuel it surges like its running out of fuel and stalls when fuel is gets low it runs fine.
View 2 Replies
My 2000 Accent 1.3 has developed a problem recently: starts fine and revs freely and smoothly when parked. When I pull away it will get very rough like it's firing on only 2 cylinders or so, at certain points during the rev range rather than continuously. Very juddery.
After a minute or so, before the engine temp is even up to normal operating temp (according to the dial) it runs perfectly. When I start it up later the same day it's fine. It only happens the first time in a day that I use it. The more days I go without driving it the worse it is.
In the last couple of years I've changed spark plugs (always in good condition when I replace them), HT leads, coil pack, a lamda sensor (the first after the exhaust downpipe) and a fuel pump and filter.
View 2 Replies
I have a 2000 LC that has a few symptoms - intermittent misfire/running rough at these times it has:
dark smoke
uses 3 times the fuel
loss of power (to normal)
will pick up revs slow without running rough and runs normal at high revs.
dies misses and then picks up revs slowly when accelerator is pushed fast to the floor from idle.
Hyundai mechanics checked computer and it coded change spark plug leads this did not fix the problem, and have no idea.
About 6 months ago the car was doing the intermittent thing when it died and liquid was heard splashing on the ground. I found the main petrol line connecting to the pump had come completely off. After replacing all problems ceased and the car ran perfect with full power etc.
I've checked the fuel lines none appear to be leaking etc.
View 12 Replies
Owning a Hyundai. I have a problem and it seems to be pretty common but haven't gotten anywhere with it yet. Last week my 2004 accent 1.6 manual transmission started running rough. It was idling higher than normal and while driving would not go past a certain rpm (about 2500 if I had to guess,no tach). On the way home from work it was running this way and then started badly misfiring and shut off, when attempted to restart it would not. I pulled the codes with a scanner and got p2400, p0562, and p0121. I charged the battery and replaced the throttle position sensor, still won't start. I can hear the fuel pump kicking on when I turn on the ignition. Also found the ecu 1 fuse blown, replaced it and continued to attempt to start with no luck, fuse was blown again. Like I said I haven't owned the car long and I don't know much about it. I am not sure where to go from here and I don't know how all these symptoms are tied together.
View 42 Replies
I just bought a 2010 Accent for my daughter and this was the 2nd time I filled it up. I realize now I should not have topped it off all the way but I did. The tank was probably bone dry when I filled it up as well. Within 5 miles after I filled it up, it started running rough and the check engine light came on. I stopped it and checked around under the hood. Checked to make sure the gas cap was tight. I drove it again and it appeared to run fine. I stopped by an Autozone and had the code checked. It was a misfire code for cylinder 3.
Drove it home (10 miles) and parked it. I took the battery terminal off and cleared the CEL. When my wife drove it a few minutes later, the CEL came on again and it started running rough. Had the code checked again and the cylinder 3 code came back. The guy at Autozone said over-filling the tank when it was empty probably caused too much pressure on the fuel going into cylinder 3 and that it should correct itself in the next few days. I drove it 20 miles to work today without any problems. It seemed like it had to be related to filling up the tank since it happened a few minutes later.
View 3 Replies
Every time I fill up my gas and put the hands free nozzle switch it clicks every time.
View 5 Replies
I've recently purchased an 01 accent GS and I've replaced the timing belt, water pump, and spark plugs. Ive also got no cold air, and original struts with 119k on the vehicle. Those are the least of my worries now as my car loves quitting out at idle; and it does not get any better hot or cold. One of the plugs was completely black when it was taken out (not by me: mechanic work) so that's when they mentioned a cylinder misfire. they wanted an additional 100 to figure out what that could be attributed to on top of the 550 for the work mentioned above! I am now next to broke and want to see if I can trouble shoot some of the causes myself. I am thinking Plug wires, crankshaft/camshaft position sensors (if there are 2 dif ones?) MAF sensor, o2 sensor, injectors, and fuel filter. My understanding is that the coil pack controls 2 cylinders at a time and I just have 1 bad cylinder...I need to figure out where to start as I have no codes to work off of. also, I don't know how to assess resistance with an ohm meter.
View 12 Replies
I have an 04 F2 50 with 6.0 with approximately 225,000 miles. I filled up with gas last Wednesday and every so often the truck will start running really rough and then it will clear up. Is it possible to of gotten some bad gas if so what products are out there to clear that up. Could've been injector going bad what are the best products for cleaning injectors. No check engine light on, gauges are good, nothing different on the scan gauge.
View 3 Replies
I have a hyundai accent, 2002, I have the typical hard to start when filling up the tank. My understanding is there are 2 Fuel Vapor Purge Valves, one in the rear next to the charcoal canister, the other is in the engine compartment attached to the intake manifold - is that correct?
Which purge valve is the culprit to the hard start after fueling the car? Why can I only find the rear purge valve when looking for parts - is the one up front a dealer only part?
View 5 Replies
It seems like my passenger door is filling with water, whenever I open it, it comes pouring out through the drain in the bottom. It also seems the water ingress has killed my central locking on that side. It's getting in through the gap between the door and the window. How to keep it out?
View 5 Replies
I have recently purchased a 2001 Accent GS which has the 1.6L DOHC engine and have done a big road trip in it which has created a problem. When I fill the fuel tank up it runs really rough, has no power, and stalls at idle unless I keep the revs up. I can also smell petrol very strongly in the car all the time, plus it's running really rich as I can smell fuel on the exhaust and the last symptom is the loss of power down low(due to running rich).
I was on my road trip so had no tools on me and got the local mechanic of a small town to do a few basic things (change spark plugs, leads, and fuel filter) but to no avail. It runs smoothly when it gets below the full line on the fuel level gauge so I just didn't fill it up completely to get the car home but it still runs really rich and doesn't have quite as much power.
View 4 Replies
I have a 2000 Hyundai Accent hatchback with 98k miles. About a month ago we were headed out of town and got gas about a mile away from the house. After filling up, the car wouldn't start. It would crank but not fire. Tried for about 15mins to no avail. Had it towed to local mechanic and it started right away. They kept it for the weekend and said they had no problems starting it, so without experiencing the problem they said they would just be throwing parts at it.
About 2 weeks after my wife drove to store and when she went to leave and same experience, but this time it started after trying for a couple of mins. Then just this Tuesday it wouldn't start in the morning. When it just cranks but not fire it shows a pending P0335 (crankshaft position sensor). So I ordered the part (won't arrive til Friday). When I got home I tried to start it as well to no avail; tried again Wednesday morning and evening, nothing. Then this morning (Thursday) it starts right up. Once its started it runs great. After recurrence of no start 2 weeks ago, I replaced spark plugs and spark plug wires.
View 6 Replies
Recently, my Accent has been acting up (twice) while filling the tank. I haven't done any work on it that would cause this recently, but while fueling, the pump will click and stop repeatedly, as if the tank was full. It takes sometimes 20 minutes just to put 8 gallons in it. I've tried two separate pumps. Next fill-up, I'll try a different gas station because I've heard that can sometimes be a problem. They said their pumps weren't empty so that's not the case.
View 5 Replies
Having an issue with my 03' Accent. I'm having an issue of my coolant tank filling up but it is not being drawn back into the radiator when the engine cools down. I have replaced the radiator with a new unit because the filler neck of the original radiator was damaged sometime in the past and the cap would not seal good enough to hold pressure . Looks like heat damage to me but I don't know for sure. The system now holds pressure but now I'm having the current issue. My first thought was a head gasket issue creating pressure in the system and forcing coolant into the tank.
The car has 155k miles and runs good overall and is not overheating. I performed a "block check" test using the chemical method that detects combustion gasses in the cooling system and that test was negative. I also pressure tested the system by pressurizing to 16 psi and was unable to detect any leaks anywhere on the engine / radiator and the pressure did not drop until I released it. I guess the next thing to try will be a compression test to see if I have any low cylinders. So, for whatever reason my cooling system is not creating enough of a vacuum to draw the coolant back into the radiator when it cools down. Does this sound like a head gasket issue? The pic is of the original radiator filler neck damage.
View 8 Replies
I have a 2000 Hyundai Accent that just started not filling up. The pump kicks off every couple seconds. From reading other posts it sounds like its the evap canister (wife would often top off the tank). The question is, does the evap canister need replaced or do the hoses need cleaned? Is there an easy way to get the hoses off?
View 4 Replies
I have a 2003 hyundai accent gt 1.6v runs great other than when I get gas. As soon as I fill my tank the car doesn't want to start. It cranks turns over idles very low and then dies. I have to try to start it about 3 times before it will stay running. Starts perfectly fine in hot or cold weather only has problems right after filling gas tank. Started about a week ago. What could be the problem?
View 2 Replies
I have a 2008 Accent 1.6L automatic that is running very rough when it accelerates. First of all there was some engine check light, I got the codes and it was a Cylinder misfire. Then I checked the following:
1.- Spark plugs (replaced them same NGK but I didn't gaped them, same result)
2.- Fuel injectors (removed them, cleaned them and installed in different order, same result)
3.- IGN coils (measure resistance, swap them in different places, same result)
4.- Checked most of the sensors including TPS, Crankshaft PS, MAF, Camshaft PS and nothing.
5.- I checked for any type of vacuum leak and I couldn't find one
After all that troubleshooting I cleaned the codes, started the car again and I have the same problem with no check engine lights on except that sometimes I would get a "running rich" code.
I also noticed that the air intake is LOUD like a performance air intake, is that something normal on the accent? (I checked the air filter and its not clogged FYI). I could only think of:
Gap spark plugs to .035
check timing belt
check fuel filter (I don't think so)
View 11 Replies
The check engine light came on after cleaning the engine and the engine runs rough. Where to look. 2007 Hyundai Accord.
View 5 Replies
Our Accent has just about 86k on it now, back in November it suddenly started running real jerky/rough, misfiring kinda thing. So I was able to drive it to my local repair shop and they found a bad coil pack on #3, so they replaced that and put in new plugs while they were doing it.
Just Saturday we were shopping about 20 miles from home and cranked it up to go home and started doing it again, pretty much identical symptoms, runs out normal at certain RPMs so I knew it was probably same thing...I was able to get it home and then took it in this morning and sure enough now #1 is shot. So they are replacing that. They want about 30$ more per coil then I can order them for myself online so I didn't want to scarf up the money for the other 2 that are still original.
View 29 Replies
Check engine light had come on, the car was running rough at idle and it would crank hard. So I threw my code scanner on it only to find out it wouldn't link. Drove it to O'Riley's and had them pull the codes. It ran rough and had next to no power on the way there. O'Riley's pulled the codes and we got a P0300 (random multiple misfire), P0301 (cylinder 1 misfire), P0302 (cylinder 2 misfire), and a P0496 (EVAP emissions system high purge flow). So once I got it back to the house, she told me that she had the codes pulled once before and that they told her it could be her gas cap so she replaced it. She also stated that she had replaced the plugs about 3 months ago.
So with new gas cap and new plugs, and these codes, I did a bit of research and come to the conclusion that it'd replace the purge solenoid. The solenoid was making a pretty loud ticking noise and when I pulled it off, it rattled so I figured that was the fix. Pulled her plugs and you can clearly see that cylinder 1 was running VERY lean and cylinder 2 was a little richer but still too lean. Plugged the plugs back into coils and laid them on exhausted. Turned the car over and we had spark. Lead me to think the misfire had something to do with the P0496 EVAP code. Put everything back together and erased the codes. Gave the car back to her and told her to let me know if the light came back on. That was Wednesday last week. Sunday she told me the light came back on and the only code that came up was the P0496 again. When I gave it back to heron Wednesday, it would still crank hard but would start.
Battery is new and checked good, alternator is pulling about 14v and checked good and the starter checked good. My dilemma is the code and the hard crank. She told me that it only cranked hard for her once so I am assuming that has gone away but we're still left with the P0496. I am not 100% sure as to how this system operates but I understand it for the most part. She told me that she had just put gas in it before the light came on. Not sure how much time had elapsed after filling it and the light coming on but I do know she put gas in it. If it's a high purge flow, that makes me think there may be a leak in the system but I'm not sure where to go from here without throwing a bunch of parts and money at it.
View 14 Replies
