Accent LC (2000-05) :: 2001 - MAF Sensor Location?
Jul 4, 2011
I'm trying to locate the MAF sensor on my 2001 LC accent. I can see the air cleaner box, the tube which T's off to the surge tank, and then it goes straight into the throttle body. On the hmaservice website, it shows a MAF sensor between the air cleaner box and the surge tank (or "resonator"). I don't have that! There's concertina tube going straight from the throttle body to the air cleaner box (with T off). Am I just missing a part?? There don't *seem* to be any unused harness connectors lying idly around the place!
View 2 Replies
Advertisement
Where the knocking sensor is located on a 2005 Accent. I am in need of finding it so that i can wire a controller into the signal wire?
View 2 Replies
trying to find the speed sensor on a 03 accent manual so I can fit cruise control
View 1 Replies
Wife's car threw a p0711 code. It says temp sensor failure or whatever. I found the part on rockauto for 22 bucks but that's not the issue. I've tried searching about this and I seem to find some stuff about elantras and sonatas. I can't seem to find anything specific to a accent. I've read that it's inside the transmission which is fine I've changed valves before and such on old rwd transmissions. But some things I find say it's on the bottom and some say the side. Also wiring is mentioned pretty often with service bulletins.
View 28 Replies
I have a 01 Hyundai Accent, 1.5L, stick shift. My CEL came on and I had it read. Mechanic told me it was P1128 (Fuel Lean) or something like that. Looked it up on line and everything said to check for air leaks and then look at the MAF Sensor. I checked and saw no leaks. Took out MAF Sensor and cleaned it with MAF Cleaner. Disco'd battery to reset computer. CEL went out for maybe 30 minutes and then back on. Didn't do anything with it for about 4 months, now car stutters sometimes.
So, I finally broke down and bought MAF Sensor and replaced myself. Disco'd battery to reset computer. Started up and engine was not smooth at first(30 seconds) then smoothed up. But CEL still on. Drove home (25 minutes) and checked again this morning. CEL is off! Only problem is that the car stutters a little at acceleration. Smooth when at cruising RPM and speed. Just stutters a little at start of acceleration and when switching gears until at cruising speed. Is this going to go away? Is the computer just getting set up after changing MAF Sensor?
View 4 Replies
My accent (2001, 1.6L, with 179k miles) has service engine soon light on. Brought it to autozone and they said the upstream O2 sensor needs to be replaced. I borrowed the socket to take out the O2 sensor. It's very difficult even with the tool, because the O2 sensor was stuck with a lot of rust. I used an extension bar to get it out finally, but now when i tried to put the new sensor in, I found the hole's thread is very loose. Tried very hard but can't get the new sensor in securely. It seems I had to replace the whole exhaust manifold. The manifold is very expensive(because it has a build in catalyst converter). I'm wondering is there a way to make the O2 sensor in secure without replacing the whole thing? if I had to replace the manifold then I probably will just get rid of this car.
View 1 Replies
I need to change the knock sensor of 2011 Accent, don't know where it is.
View 7 Replies
I cannot find the location of the knock sensor in my 2012 Accent. I just replaced the radiator and had everything off up front unobstructed and couldn't find it. Looked in back, sides, but am completely stumped. I have found information on earlier models but not 2012+.
View 37 Replies
2009 accent, cant find its location. Picture would be nice...
View 4 Replies
I have a 2009 Hyundai accent. 2 cylinders misfire. I changed out the spark plugs after the misfiring began and the 2 cylinders that misfire don't follow any specific ignition coil, it's just 2 random ones.
Looking at the data with a reader points to fuel injector number 1 not working properly. The first few seconds the car is on the check engine light blinks and fuel injector 1 spray duration (fluctuates based on gas applied) changes just like all the others. However, when the check engine light goes solid (then the misfire code is thrown) fuel injector 1's spray duration is stuck (usually around 3.5 ms)
The cable going into the fuel injector powers those little troubleshooting lights like it should until you plug the cable into the fuel injector OR remove and replace the light a few times.
I don't know much about cars but someone told me to try cleaning out the Mass AirFlow sensor as they had the problem above and the MAF sensor was the cause. I can't find anything on where the MAF sensor is located though.
View 5 Replies
I'm looking for the location of the knock sensor I can't find it?
View 4 Replies
Where the ECT sensor is located? I would really like to have a diagram of the engine. Where I can find an engine diagram for a 2008 accent gls?
View 3 Replies
Where is the cam sensor on a 2000 chevy metro 4 cyl. ?
View 1 Replies
My santa fe is throwing a vss code. I was trying to replace it but was not sure exactly where it was. Is it the one right under the air filter box or is that a crankshaft position sensor or some other one?
View 12 Replies
Where exactly is the coolant temp sensor located on a 2000 F-150 4.6 V-8.
View 5 Replies
My 2001 Hyundai Santa Fe V6 is giving out a P0118 code, and the "freeze-frame" data reports a -40F for the coolant temperature. That doesn't make sense so perhaps the sensor is faulty or perhaps the sensor connector is loose?
I'd like to take a look at the coolant temperature sensor but I cannot find it. I have scoured hmaservice, hyunda-forums but all the various pics are still not clear enough for me to actually find the sensor. I have seen all the online pics from Hyundai but I can't get my head around exactly where the sensor is - the pics are either too zoomed in or so many things have been disconnected for the purposes of taking the picture I can't get my bearings.
View 9 Replies
I have a 01 Elantra and my daughter has a 02. Both cars have the camshaft sensor at the front (timing belt) end of the engine. My daughters car is a early model with a 01 engine in it. My understanding is that later 02 engines moved the camshaft sensor to the ignition coil end of the cylinder head. My question is did the timing remain the same so that if I put a 01 engine in a late 02 body and spliced the sensor in would it work correctly?
View 8 Replies
My Santa Fe indicated P0715 for input speed sensor problem. I purchased both sensors and based on forum input I removed the air box and battery to access senors. Output speed sensor is easy to see and access. I am having a problem locating the input sensor. I see wires going to a sensor under both the main wiring harness and shift cable. Is that the location of the input sensor? If so how do you move the wiring harness and shift cable to allow access? If not, where is the input speed sensor located? The Santa Fe is 2001 V6 2.7L.
View 8 Replies
I've got a 2001 f150 XLT and I've checked the Haynes manual and searched Google but I'm having no luck.
I'm trying to locate the sensor for the Automatic Head Lights.
I had a small "spill" on the dash at night and immediately the lights started to blink and click. It fixed itself but sometimes it will do a weird little "click, click noise" change thing. I would like to clean the sensor or ensure it's not partially blocked.
View 2 Replies
I can't seem to find the location of the neutral safety switch on my 2005 accent 5 speed manual. I removed the air filter box and looked all around the top, bottom, and sides of the tranny. I have the new part so I do know what it looks like.
View 6 Replies
The MIL light up and I got the P0501 Code. (Speed Sensor. I use a Scangauge II and the Speed is 0 KM/H at any speed. (was working before). But the in dash Speedometer work no problem. I look on the HMAservice web page and did not found where is located the Speed Sensor.
View 9 Replies
