99 Blazer With ABS Brake Pedal Just Went To The Floor And Car Stopped Eventually
Jan 9, 2012
I have a 99 Blazer 4x4 with ABS. Brake pedal just went to the floor and car stopped eventually ... a bit scary. I've checked all the brake lines and the inside of all wheels and there is no sign of fluid anywhere. All pistons seem to be where they need to be with backing plates nicely visible.
I pumped the brakes quite a few times and same result ... but I'm not pumping fluid on the ground. As expected I've also checked the reservoir and its full. Didn't see any leaks so its full. I'm guessing that the master cylinder has given up the ghost ... truck has 470,000km so things wear out.
View 5 Replies
Advertisement
Last week my brake pedal started going to the floor when I stopped, it still stopped and felt fine on the top half of the pedal travel but then it would just slowly fade to the floor. I took it to a local shop and they said the master cylinder was leaking internally and my rear brakes were shot. I have 75,000 miles and the rear brakes were original so I told them to fix it. This is basically what I expected it to be.
They kept thinking they were getting defective master cylinders but after the two Napa parts and two Carquest parts they realized they misdiagnosed it and said I needed to take it to the dealership. I paid for the rear brake job since it needed done anyways and have an appointment for next week at the dealership. What might be causing the problem? I see no brake fluid leaks, no vacuum leaks, the booster was replaced 25,000 miles ago due to noise, no ABS light on, no CEL on, no other symptoms.
View 14 Replies
So tonight, I lost most of my brakes. If I kept at low speeds and pressed the pedal to the floor I could eventually stop, but not well. I imagine this might be more of a general question not specific to Ex's, but I thought I would start here.
View 4 Replies
Around 8 months ago my blower fan started intermittently blowing and eventually quit. The chain shop near my house told me no question it was the blower motor gone bad. Last night I replaced the blower motor (pretty cheap part) and still nothing. I can feel the engine change idle when I turn the cooler on but nothing blows. My regular mechanic told me he thought it was the resistor based on my description (though I had assumed with a resistor issue it would tend to blow on low speed but not high and this blows never). What it could be?
View 4 Replies
I was driving around today and had to hit the brakes really hard for the first time. ABS kicked in and during the ABS 'action' the brake pedal rapidly went to the floor. With each 'pump' the ABS made it felt like the pedal sunk slightly.
This was on dry pavement, a little gravelly / dirty and the car stopped rapidly, but just as I stopped the pedal was VERY close to the floor, and with just a touch more pressure it did in fact hit bottom.
Sounds to me like the ABS pump needs to be bled, is that right? Can I do that myself with a VAGCOM? I hate having the dealer do anything, even if it is their job. How to SAFELY confirm if cars does / does not do this as well?
View 8 Replies
Around 8 months ago my blower fan started intermittently blowing and eventually quit. The chain shop near my house told me no question it was the blower motor gone bad. Last night I replaced the blower motor (pretty cheap part) and still nothing. I can feel the engine change idle when I turn the cooler on but nothing blows. My regular mechanic told me he thought it was the resistor based on my description (though I had assumed with a resistor issue it would tend to blow on high speed but not low and this blows never).
The diagnostic fee if it isn't the resistor is $60 an hour so I have a feeling it will be cheaper to just swap out all the parts. I have a feeling it is the relay but I am worried that since I can tell the engine changes idle when I turn the AC on it isn't, though I do not know for sure. Also if it is the relay there are three relays against the firewall and I am not sure which it is as the cases on them all appear to the untrained eye to be identical. Included is a picture. Which relay is the blower relay.
View 13 Replies
2005 Volvo S60 T5, 90,000 miles. The brake pedal depresses almost to the floor. Dealer service has not had a solution to this problem. All brake components are supposedly nominal. Might pedal position sensor be faulty?
View 1 Replies
My 04 Camry is having brake issues. It has 205k miles. The front pads are great and the back shoes are great. (Drums in back) I've had them adjusted multiple times but my pedal still goes almost to the floor. It's not the master cylinder cause I've already replaced that. The pedal doesn't bleed off either. But I have bled the brake lines and there is no air left in the lines.
View 14 Replies
My mother went out 2 days ago to go run errands, she stepped on the brake pedal and it went to the floor (car still in garage and in park, low mileage car 81,xxx garage kept). I have not been able to duplicate the issue. The fluid has been changed twice since new, no signs of fluid loss, undercarriage inspection revealed nothing. I am thinking maybe a vacuum hose issue.
View 2 Replies
When I go to start and depress the brake pedal it goes all the way to the floor. The brake fluid is at the full mark and my 2011 has only 25k miles. Where should I look since it did not go all the way to the floor when I forst got it with 6K miles.
View 19 Replies
I drive a 1991 F-150 Lariat Extended Cab. Out of the blue, my brakes decided they didn't want to work unless the pedal is about 1/2 - 3/4 of the way down to the floor. As soon as I release past that 1/2 mark, they shut off. While this makes it great for tailgaters, it does not make it great for police officers.
We have already replaced the switch thinking maybe it was that, but alas it was not. I was reading in a couple difference places about the multiswitch? However, the symptoms other people had were similar, but not the same. I never tilt my steering wheel, so I dont know if that's the issue!
View 2 Replies
2013 Prius c Two, bought brand new with 15 miles on it 5 weeks ago. A few times when driving, I noticed the brakes seemed weak, like they weren't stopping the car very well even at low speeds (My driving is mostly in town on residential streets, so I'm rarely going over 35 MPH. Even so, I'd have to really mash the pedal all the way to the floor to get the car to come to a complete stop, otherwise it would keep moving forward. Several times I ended up about 5-10 feet past the line, sticking the front bumper into cross traffic. Luckily no one hit me. I chalked it up to the quirks of a different car than the one I was used to, and figured if it kept happening I'd take it to the dealership.
On Monday, my wife was stopped at a red light. The light turned green and the car in front of her started to move forward. After a few hundred feet, he suddenly slammed on his brakes. She said her brake pedal went all the way to the floor, and the Prius didn't slow down at all. She hit him going about 25-30 MPH and totaled the Prius. She's an excellent driver and I've been with her before when she's had to panic-stop. She's never driven a car without ABS, so she is used to pushing the pedal hard and keeping her foot on it. She wouldn't even know how to "pump" the pedal. She swears the pedal just went all the way to the floor and the car didn't slow down at all.
View 18 Replies
For the past several weeks, my daughter reports that she has to put her foot almost all the way to the floor to get the brakes to work. The brakes do not have an effect until her foot is 1-2 inches from the floor. It usually happens after she has been driving for a while without pressing the brakes. I’ve driven the car numerous times but haven’t been able to replicate the problem. Her commute is approximately 10 miles each way in stop and go traffic. The car is a Volvo xc70 with 200k+ miles. I've had it looked at by a mechanic who didn't find anything but it's continuing to happen. I'm suspicious that it may be a master cylinder problem and concerned about complete brake failure -- should I be?
View 7 Replies
When I press the brake pedal, the car will stop. But if I keep pressing it while the car is stopped, the pedal wants to keep going towards the floor. I have to press hard for it to do this. I have bled the brakes. I've checked the calipers and the hoses for leaks and don't see anything. The master cylinder is topped up and I don't see any fluid underneath it. It doesn't appear to be leaking. The funny thing is, when I turn the engine off and press the pedal, the pedal comes to a stop and doesn't want to move after I pressed on it as hard as I can.
View 2 Replies
I have a 2007 Sonata GLS 4cyl. Anyhow lately my brake pedal is going right to the floor. The brakes seem to work fine, but if I keep constant pressure on the pedal it will slowly go all the way to the floor. My rear rotors and pads have been changed a couple of months ago and I'm pretty sure my front brakes are good. What could be causing this? I also checked underneath the car for leaks and there doesn't seem to be anything leaking underneath.
View 6 Replies
I have been working on my 01 Elantra for 2 days now. My problem is that I have absolutely no brake pedal at all, it just goes right to the floor. and this is only when the car is running, when it is off I give it a quick pump and i have a nice firm pedal. I installed a new master cylinder, bench bled it and all that jazz. I replaced the rear brakes and a wheel cylinder, I have also bled the brakes multiple times, and mutliple ways. bled the master while on the car and all the brakes while the car is off and while it is running. I dont know what else could be wrong with this. I looked at all the lines and there are no wet spots, no hoses are swelling up. everything looks top notch...i just have no brakes why.
View 15 Replies
My Sienna 2005 experience intermittent complete brake failure 3 times within 18,000 miles,the brake pedal goes to the floor and it does not slow down, so I coast until I stop. However, when I release the brake pedal and then reapply the brakes, it works fine. A non-Toyota mechanic thinks it's due to malfunction of ABS. The dealership is unable to finds error codes and brakes work fine when the Sienna is in their hands. I scared that the brakes will not work the next time I reapply the brakes.
View 30 Replies
A friend brought me a car with the issue that the brake pedal sinks to the floor when braking. She said it was never low on fluid so I replaced the master cylinder and bled all of the lines with a friend pumping the pedal. The pedal would still sink to the floor. I tried vacuum bleeding the brakes and found that the front left consistently had large bubbles.
I Teflon taped the fitting on the calliper and the bleed screw which improved the problem but didn't fix it. I then replaced the calliper. The front left calliper still won't bleed and the brake pedal still goes to the floor. When I bleed it the regular way, the fluid comes out of the bleeder like it bled nicely. Neither of the rubber hoses that connect to the calliper have any visible damage. I had a friend pump the brakes while looking at the hoses and their is no bulge or swelling in them. Could the ABS need to be bled?
View 4 Replies
I have a 96 voyager, it has been a great car for the last 10 years I've had it. My brake pedal goes down to the floor, it gives brake but I think barely and my brake light comes on. I have Bled it twice and changed the master cylinder , neither worked, I'm perplexed, my mechanic thinks it is the abs.
View 3 Replies
My B6 purchased exactly three weeks ago has had a soft brake pedal since day one. By "soft," I mean that when parked with the engine running and applying moderate pedal pressure, the brake pedal provides some resistance but sinks to the floor. If I pump it up a few times, it temporarily gets much firmer, but eventually sinks to the floor again after a few seconds. Now the car so far has never failed to actually stop, and it can get into the ABS. But during an abrupt (okay...panic) stop last week, it did go to the floor while the car was still moving. That's when I decided that was enough and took it back to be serviced.
My expectation was that there was just a small amount of air in a line somewhere, and that they could bleed the system and fix it. That was my experience with my B5: it was very sensitive to the least little bit of air, and if it wasn't thoroughly bled after brake service the pedal often got mushy and could find the floor. But bleeding them always get the pedal back to normal. So the service advisor said that he "had the service manager drive [my car] and compare it to a new Passat [on the lot] and talked to "Quality Tech. Manager to confirm." And the confirmation was that my brake system is "working as designed." In short, they say the brakes are working properly and there is nothing to fix. So I have now picked up the car and it still does the same thing.
Now I can (and will) bleed the brakes on my own over the weekend. But I would like feedback from others as to whether or not their brake pedals regularly see the floor. I just can't see this being the way any hydraulic brake system should work..
View 21 Replies
Back brakes don't bleed. car doesn't stop anymore. The passenger back brake stops even though it doesn't bleed, but the driver side brake doesn't make the tire stop and it doesn't bleed. The e-brake works. I just need to know what could be wrong. 1995 Oldsmobile Cutlass...
View 8 Replies
