on a 93' 4 runner that will not engage 4 wheel drive. The 4 wheel manual shifter works fine, and the linkage underneath looks fine; however, the indicator does not light up - and it definately only has rear wheel drive.
View 5 RepliesNot so simple as an unbalanced tire. Left front wheel/tire starts shaking at about 35 mph, worsens with increase in speed up to 52 mph then quits shaking. Some residual (though minor) vibration after that. Had tire balanced already at a good shop so I don't think that's it.
Struts are due for replacement - could that be part of the problem? I've had the thing on a lift and don't see anything indicative of a ball joint or an a-frame bushing, BUT, is it possible/probable that my problem is one or more of the latter problems combined beyond the tire issue?
I have had an issue with my GX470 almost since I bought it in 2008. It will sometimes not engage in drive after backing out of a parking space.
It usually happens when it is warm and the car has been driving for awhile then I park for lunch or an errand. I come back start up the car put it into reverse backout of the car space and nothing for a good 5-6 seconds. Seems a lot longer when cars are waiting to take your space and honking.
Anyway I have been reporting it to Lexus at every service and getting a no trouble found. Over time it is occurring more regularly and it even happened at the dealership but of course I was the only one in my car at the time.
I have an 01 s10 with the 3 switch 4x4. When I switch into 4hi I hear the click at the dash and I hear the switch on the transfer case but it doesn't engage in 4x4. The lights o. The dash act normal and says its in 4 wheel. I've had problems with the switch on the front of the transfer case in the past and was able to clean it and it was OK for awhile and now nothing. I replaced that switch and hear it working but still not engaging. I did notice a bad vac line on the firewall but not sure where it goes yet. Is there an order I should be checking components? What should I look for next? Also should mention in 2hi I get a whining noise like a shaft is spinning but when in 4hi the noise goes away and it drives like its in 2hi.
View 1 RepliesAfter I push the switch for the 4 wheel drive, the light on the dash blinks but the front differential won't lock in even after driving around the block.
View 14 RepliesI bought a 99 ranger few months ago cant the 4x4 has not worked in the truck for about 4 years. Bought it off my dad. He hasn't figured it out the t case locks in the drive shaft spins but hubs will not lock in. Has new hubs in it and still not working. Trying to get it fixed so I can park the diesel for the winter and run the ranger.
View 3 RepliesIts a automatic transmission with a v6 4.3 vortec. The front axle will not engage, it is not the acuator (I replaced it and the cable) you can pull the cable and the axle will engage. There is a low buzzing noise(coming from the drivers side) until you give it gas. This noise stops when the front axle is engaged. The transfer case will go from hi to low without any problems.
View 1 RepliesI have a 2007 Santa Fe crdi automaticl. When I push the 4 wheel drive button, the light in the dash goes on but the axels do not lock up. There is no code number that show up. Is this a sensor problem or what?
View 1 RepliesI have a 1998 F-150 and when shifting into 4 wheel drive (manual floor mount shifter) the drive shaft from the transfer case turns but the wheels do not engage.
Looking for a diagram of how the axle works?
So my Push Button 4 wheel drive wont engage. The light on the dash wont light up and it doesn't shift into 4x4. Where to start? I would like to check the simple stuff first. O and my heat only gets hot when im giving the vehicle gas. This is all on a 2003 Ford Explorer.
View 2 RepliesI have just switched from GM to Ford and have a new F250 4x4 XLT. I am wondering how to engage 4 wheel drive correctly. I have the manual shifter and the manual lock hubs. However during my test drive I shifted the lever into 4H and 4L and it seemed to engage just fine. Do I need to lock my hubs as well? Or if im just in a wet spot can i just shift into 4h without locking my hubs? I know if I am in anything serious I need to lock the hubs. I just want to be sure before I get into a tricky situation. My 02 GM all i had to do was push a button and it shifted automatically.
View 7 RepliesI have a 92 4runner with v6 5speed Manual tranny it has the A.D.D hubs ,when I put it in 4wd its not going into 4wd the 4wd indicator in dash is not coming on ,that could be a bad bulb cause it doesn't come on when you turn key on.The transfer case is working all right .Its something in the front end that's not engaging .I noticed on the front diff. there is some kind of solenoid there with vacuum hoses and a electrical connection .Does this have anything to do with it not locking into 4wd?
View 2 RepliesI have a problem with my 4runner, it ran good when I drove it before I deployed, not I got back and it will not run, it starts for about 30 seconds then dies, sounds like something is killing the fuel, I took the cap off the tank to see if it was clogged, but thats not the problem, it just will not stay running for longer than 30 seconds. Also I realized that the alternator was very hot for the 5-7 times I started it and had it run for 30 seconds? Oh it's a V6 3.0L 5SPD manual 4X4 by the way.
View 3 Replieswe have just pulled out head resurfaced and put engine back together now it won't start tried the timing and checked for fuel but wont start the only way it starts now is with brake fluid in the intake but that only fires up and won't stay idle.
View 3 RepliesI've noticed that my brakes are very sensitive lately. I'm wondering if it has anything to do with the differential oil that got on the rear pads when the rear seals blew out about 3 months ago. The shop cleaned them off but they still looked oily to me. I'm also wondering if it is parking brake related as one or both of the bellcranks are frozen (there's no cable sag, but one of the stops has a gap and the parking brake doesn't work). Or is it brake fluid related. I am years past the point of needing to replace the brake fluid and bleeding out the old fluid.
View 5 RepliesThe transmission went out on my toyota 4 runner ...
View 1 RepliesI have a 93 4Runner, and it won't start all it will do is turn over, But won't start, my dad has tried everything we could think of It has gas, an new battery and new battery cables...
What is the location of the MASS AIRFLOW SENSOR, AND THE MAIN COMPUTER...
The son inlaw just bought a 86 4runner. It's been beat pretty good but I know Toys are good for it. My question is, it rev's just fine in every gear but 5th. Going down a flat highway and in 5th it won't rev over 2500 no matter how much gas ya give it. It has a 22re and 31-9.50's under it. My daughter had a 86 p/u with a 22r (I believe) and 33-10.50's and it had no problem hitting 90. Is there a limiter on these things? Thought i'd ask before chasing vac lines.
View 2 RepliesI have a 91 4Runner SR5 V6 3.0L that has been a great truck (like all of them?) until just recently.
Symptoms are bogging at roughly 25 mph or 2500 rpm in second to third gear. It will also sometimes not take off from a stop at a slight incline. By hammering the throttle down and forcing a downshift, the truck will rev up and then accelerate, but then again sometimes bog down until the same "forced shift" is done.
This seems prevalent when the engine is hot, however, that may be coincidental with the high temps here in So Texas lately. The truck does seem to run fine for a while after starting it. Mechanic hasn't isolated anything.
'91 4Runner, V6, 3.0, 113K miles. It has a nasty bog on takeoff, doesn't seem to clear out until over 35 mph on flat ground, and you can forget about starting from a dead stop going up any sort of incline.
It still has the stock plugs, so I figured those were up for changing anyway. While I was at the shop, I went ahead and picked up a new air and fuel filter. I decided to try one thing at a time, started with plugs, got em in fine, took it around the block, wouldn't idle, sputtered pretty bad, stalled at every stop sign.
I figured that the fuel filter was in fact clogged, and maybe the new plugs were causing it to starve for gas? Crawled under the car, and the cat converter was cherry red hot. I put in maybe half a mile, so could that be my problem? It has begun to rain, so I have not installed the fuel filter. I've heard some stuff about sensors going bad, namely the CTS, but that is getting a bit in over my head.
I have a craigslist nightmare vehicle in the shop today, a 98' Toyota 4runner Limited V6. Runs and drives fine, but it's got a heck of a growl in the front end over 15mph. We removed the diff and found that when it was turned it had some vibration and a ton of noise. Disassembled it and found it to be full of metal flake, and it appears the spider gears are worn and causing a good lot of the noise. The bearings seem to be alright, but I'm planning to replace those anyway while we're inside, due to the amount of metal in the fluid.
My questions are:
1. Is this a common failure?
2. Where can I purchase spider gears? Most places don't seem to list them.
3. Is there a rebuild kit that includes bearings and spider gears so I can make one part order and run with it?