4l60. Tranny 08 xpress. I'm getting p0700 code. 2 weeks after first getting code the tranny went out. Replaced tranny but still getting the same code. Should I b worried and how can I fix it.
View 3 RepliesSo of course it has to happen 3 weeks after my warranty expires. My CEL comes on and I have it read and the result is P0440. I find out that my wife has a habit of topping off the gas tank and so I am thinking that she has probably ruined the charcoal canister. It is something easy to replace?
I have an 06 limited edition... Yes, she will not be topping off any gas tank anymore.
I have a 71 F250 4x4 with the 435 and recently had the tranny out to replace the output shaft i believe its called, and other than the shaft it seemed all was well. Shortly thereafter it became impossible to shift it into 4th gear without it grinding. I am able to minimize it by double clutching and keeping the rpms right, but the grind is unavoidable and its only 4th gear, all others shift fine. I was hoping there was a way to adjust the clutch but if not am i going to have to pull it back out and look at the fork and gears? But like i said, we just had it out and the fork and gears seemed fine.
View 5 RepliesI need to replace O2 Sensor which is Bank 2 Sensor 2 which needs to be replaced.
Where is this located on a 2009 Hyundai Santa Fe 3.3L
My 2005 PT Cruiser (not turbo) is giving me a very frustrating P0700 code and a weird problem. First thing in the cold, autumn, the car drives perfectly fine (through still with the engine code on). Once the day warms up a little, the transmission decides that shifting past second gear is for punks and won't do it, so 30 mph has the engine revving at 3K rpm.
My morning commute is 20 minutes, and in that time, I go up to 50 mph with no issues. Driving home, or any other time of day, becomes the issue. What in the world could possibly be going wrong? I've been trying to hit up the junkyard for a PCM to see if switching that out would work, but it's been too rainy and cold to get out there.
I have a 2008 GC 6 speed transmission that has 55000 miles on it. When the engine and tranny is cold the transmission shifts very hard until it warms up. There are times when shifting from reverse to drive it shifts very hard. Also, the siding doors creak when driving over rough roads. Can they be adjusted?
View 2 RepliesCould a bad transmission cause error code P3030 and P3009?
This car has no other symptoms other than the Mil light and the check engine light.
I have a Toyota prius 2008 with 130,000 miles. I kept getting red triangle sign, the car will slow down and will need to pull over, shut it down and restart. I went to the dealer. First they diagnosed 12V battery issue, so we got that replaced. The red triangle sign kept coming, so we went to the dealer again, they replaced transmission fluid. They said it was low on transmission fluid. The red triangle sign kept coming. So we went to the dealer again. They said it is transaxle internal problem. The diagnostic code is P0A37. I have a couple questions. In California, what is the warranty for Transaxle problem. In some posts I saw 180,000 miles, 10 years. The dealer said they called Toyota and Toyota does not cover the repair. It is a costly repair. Second , is this code really requires Transaxle replacement.
View 16 Replies I have a trouble with my 2008 prius; red triangle engine light is coming and when i try to push the gas pedal it feels like it's freeze, the car does not accelerate so I have to stop.
After i turn it off and start again it drives ok, but a triangle is still there and there is error code POA90 ( two different scanners show same code with two descriptions; the first is "MOTOR PERFORMANCE"; the second describe it as "14-volt power module system voltage high").
Specially it happens when i drive up the hill and push the gas pedal harder. What it can be? I took the car to the Toyota dealer; they looked for 8 hours and find nothing; i can't do it again as the car do not have a warranty and the dealer charge for hours.
I have a 2008 Sports Trac, with a 4.0 SOHC engine ... 165k miles. Last week my check engine (CE) light came on and the code is P0401 ... too little flow on the EGR system. I first tried cleaning the existing valve - but CE light still came on. So I replaced the old EGR valve, cleaned the SS tube from the exhaust manifold back to the EGR valve and the CE light is still on. I have not driven the truck since I replaced with the new valve ... only fired her up in the garage. Is this something that could possibly clear up given a couple of miles?
View 6 RepliesI just bought a F150 with 103,000 on it. The engine is a 4.6. I get a P0605 code every now and then which doesnt effect performance. I erase the code and it doesnt appear again for maybe another 100 miles.
I suspect a loose connector but not sure. Looked up the code and it reads PCM READ ONLY MEMORY (ROM) ERROR. My question is what does the PCM operate? And wheres a good place to start troubleshooting?
I have the error code P0340 and have changed both camshaft positioner sensors, cleaned the air sensor and throttle body and still the engine stalls. I can accelerate at 40, 50, 60mph and it jerks violently. I tried the "locking it in third" trick but it still jerks. Today I unplugged the left cam sensor and the truck idles @ 400rpms, does not stall, and pretty much drives great! Hook it back up and crank it, within 10-15 seconds it stalls. I plan to check the wiring....
View 14 RepliesI have two codes off my "digi moto lite" obd2 scanner....
P0201 - internet search suggests it's a fuel injection code....
However I can't find anything on code C3203....
I recently changed from a problem-ridden SCT Livewire to a SCT Xcalibarator3, and now when running my custom tune I get a check engine light and a error code P0605. I never got this on the same tune with the Livewire. What causes this and how to fix it?
View 4 RepliesWhat would make the OBD II not read the code that is set on my truck. It says "Communication Error..." Fuse 41 grants power to the Diagnostics port and the cigarette lighter. The cigarette lighter is working. Any other reasons I can look at?
View 3 RepliesI'm trying to find information about replacing solenoid in my transmission. I have pdf of repair manual, and it doesn't have much information regarding transmission.
I have a p0766 code, and I think I need to replace Shift Solenoid. Does Technical Information Service Cover this with subscription.
My 2007 Ford F150 Lariat (5.4L) with 82k miles popped a P0307 (#7 misfire) code one chilly morning. It began stumbing and hesitating a bit between 25-35mph, and each time it occurred, the engine light would flash on and off. Hesitation clears and light goes steady. Cleared the code and didn't see problems again for a month...until the next cold day (freezing temps). Popped again and hesitation returned. Ford dealer wants to change plugs. I've read coils can also cause the issue. Not sure if I can do either myself.
View 4 RepliesI have an 08 avalon w/ 281k miles. NEED to replace the transmission speed sensor (P0500 code thrown). Where is it located on the trans and what is the part #? I'm thinking about servicing the trans while I'm there but looks like a lot of "comments" regarding this transmission and the problems with servicing it!?
View 9 RepliesI have a 2008 Camry Hybrid and recently got a "Check VSC System" warning light. A diagnostic resulted in a C0210 error code. The code is for a right rear speed sensor malfunction.
I had a local shop look at it and he replaced the hub accembly including the speed sensor. It didnt work. He and I took a ride and on his diagnostic tool, the speed reading for the right rear wheel was all over the place.
The next day he replaced it thinking that the new sensor was bad. This worked, however only for a day. Now the light had come on again with the same error.
I have a 06 F150 and I am getting the P2207 code on it. Sounds like a O2 sensor has gone bad. From reading a little about it online, it sounds like there are (3) different ones on the truck. Is there any way of knowing which one has gone bad or do you just have to replace all of them? How hard of a job is it, do you need a special tool to remove the old sensor?
View 1 RepliesI am getting error code po457 Evaporative emissions error, I am told the canister purge valve could be bad.
View 4 Replies