3 Series :: 1995 BMW 325is Start To Get Hot On Highway When AC Is On
May 28, 2013
Just bought a 95 325is. On highway it starts to get hot when ac is on, turn ac off and the temp returns to normal. Doesn't happen on residential streets or at idle.
View 2 Replies
Advertisement
95 850 died on the highway - now it cranks and won't start. I had it towed to a mechanic who later told me he didn't work on Volvos. He did however check for spark - good. Timing belt- good. I replaced fuel pump and relay - no go. One possible hint is the lights on the Sport/Econ switch no longer light up and the first light I saw when it died was the up arrow light on the dash. Last winter I cleaned and regreased the PNP switch. Would that have anything to do with it?.
View 2 Replies
I have a 95 Ranger with the 2.3L and it is a five speed. I am having a starting issue. I have replaced the ignition switch, clutch position switch, starter relay and had the starter tested. The truck will not start with the key. I can jump across the relay and it starts fine but will not even click with the key.
View 3 Replies
I have a 95 Ranger 2.3 with a manual tranny. In the past I have had problems with this truck not starting do to a bad inertia switch and numerous fuel pumps. A couple of weeks ago I pulled the truck off of the driveway into the street and let it set there for a few hours. When I went to put it back on the driveway it would not start. I got it pushed on the side of the garage. I did my normal routine of doing a pressure check. I had no fuel pressure so I assumed that it was the fuel pump (as usual) so I dropped the tank and changed the pump.
I got it back together and it still wouldn't start. I checked the fuel pressure and the manifold still had 0. So I started my diagnostic. I have power from the fuse to the fuel pump relay. I then checked the wiring at the inertia switch and found that there is no voltage with the key on at the supply side of the inertia wiring. I verified continuity between power distribution block and the inertia switch. I put in a new fuel pump relay and it still has no fuel rail pressure and there still is no electric signal at the inertia switch. Where to go from here?
View 6 Replies
I have a 1995 ranger with a 4.0 it cranks just fine wont fire has alot of fuel spark it will crank and crack then it stop and acts like it is going to fire up and stops cranking. This thing has 253k on it.....
View 6 Replies
My 1995 ford ranger with a 3.0 will not start. It acted like the fuel pump was going out so I replaced it. I also replaced cmp sensor and the camshaft synchronizer due to old cmp sensor broke and messed up the synchronizer. My truck is getting fuel and spark but still will not start. Where do i go next?
View 4 Replies
I have a 95 Ford Ranger 2.3L with a five speed. I recently had a starting issue were I parked the truck, went into a store came back out and the truck wouldn't start. Figured it was the solenoid as I couldn't jump across it to get the truck to start. Replaced the solenoid. Still no go. Found a fuse in the starting circuit blown. Replaced the fuse and got it started and drove home. Next morning, I go to leave for work and the truck would not start. Got a ride to work came home and checked it over and found the starter locked up. I replaced the starter. Truck started for a few days and now I am having problems again.
Here is the problem I am having now. Starter is good. Proved that as I can start the truck by jumping across the starter relay. Checked the solenoid with a voltmeter and it is doing what it is supposed to do when the truck starts normal. Here is where I am scratching my head. I can start the truck sometimes and it starts just fine. Next time I try to start it, the fuse will blow.
Replace the fuse and it might work for a couple of starts and then the fuse will blow again. I jumped pass the fuse with a piece of wire for diagnostic purposes. Out of 20 starts, it only started normally 4 or 5 times. I have checked every wire I can see under the dash and have not found any obvious issues. I am at a point where I am so frustrated that I just want to push this 400k mile truck into the back forty and put it out of its misery like a lame horse.
View 9 Replies
1995 ranger. 132k miles. I have been having an intermittent starting problem. I replaced the battery which was 3+ years old. I thought that cured the issue because the truck started without a problem then, the same problem occurred. I started the truck and drove about 10 miles. Parked it for about 2 hrs. Went out and tries to start it. The engine cranked, but would not start.
Tried a second time and would not start.
I turned on the lights and proved the battery was good.
Tried to start it and it turned over.
I took it to a shop and they could not fine the problem.
I asked if it was a possible problem with the solenoid, alternator,
They said if it was those the engine would not turn and you would just hear a click.
They drove it for a week and it happened to their technician but he said he did not have his equipment to check it.
He got it started after a few tries as I did and got it back to the shop. Ran a scan.
Four codes returned that really did not identify the issue - P0231, P1701, P0340, P1270. They cleared the codes and drove it again. They checked the codes. It showed code P0340. The shop says the code states to replace the cam position sensor and installing an updated DPFE sensor.
I have been driving it for about a week on and the problem has not resurfaced yet. A friend whom I work with does some car maintenance told me it is a dead spot on the starter and to replace it.
View 14 Replies
The car's engine just stopped while driving on highway, then would not turn over, nothing.Took for repair, said battery had bad cell or something, still under warranty, replaced.Fixed a few other things that were overdue, spark plugs, wires.
Okay. Next day, took the car on a few city driving short trips. While going across town on hot 85 degree day w/ ac on, it died again. Don't remember any lights coming on, didn't last time either. I think the AC died first then car died. Wouldn't make a peep. Right in middle of heavy traffic. When police came couldn't even steer. There might have been a slight weird noise which I thought was the ac making trouble right before it stopped, can't describe it really.
Had it hauled to shop again. It runs fine for them so far. They are still working on it.What in heck could it be? All belts were replaced a few years ago, car has always run well, never any major repairs just maintenance. It has about 133,000 miles on it. It has a clutch.
View 10 Replies
Got a strange one here. 1995 Buick Park Avenue, supercharged 3800, 159K miles... an older car, but an unmolested one. A little over a week ago I began to notice an occasional miss when cruising along at highway speeds, along with a slightly rougher idle. Both the fuel filter and the plugs/wires predated my ownership of the car (a little more than 6 months); so seeing no obvious culprit, I replaced them and hoped for improvement.
Unfortunately, neither had any impact. The missing continued to become more noticeable. It was never present under acceleration. Most of it was like a split-second long version of "bucking" that could be observed while cruising at lower (<2000) RPMs. It was also very noticeable at idle. Eventually a code was set: P0341, camshaft sensor issue. If the story had ended there, it would have been just another night in the garage. But it didn't.
As I was noticing the aforementioned symptom increase, I also noticed my voltmeter would occasionally "twitch" in the downward direction. Eventually I had an incident where I came to a stoplight... transmission in Drive, foot on brake, gauge dropped to around 10-11v. It returned to 14v momentarily, but dropped back down, held there for several seconds, returned, etc. No particular rhyme or rhythm. Of course my first guess was that the alternator was failing; a separate problem from the other.
I checked all the relevant connections (at the battery, at the alternator, etc), and cleaned them for good measure. All were tight, relatively clean, and the cables showed no resistance on the ohmmeter. It happened that I had another correct alternator on hand (used/working pull), so I swapped it in. No change. I reinstalled the original and was back where I started.
On my most recent drive, I noticed both issues had become very noticeable. The drop in voltage was happening at nearly every stop, and the missing was happening a few times per minute while coasting along. There seemed to be some correlation between the missing and voltage fluctuating, but it wasn't absolute.
I decided to attack the voltage issue again. Re-checked all the cables; same result as before (all OK). Looked all over the car for possible bad grounds, loose connections, or other visible problems, but found none. My next thought was to run a jumper from B+ to the voltage regulator's Sense input (have seen issues there on more than a few older vehicles) - but after reading that this car uses the PCM as the voltage regulator, I didn't proceed.
Just to be certain I'm going to have the alternator tested by the local auto parts store. But I suspect it'll pass.
View 8 Replies
Recently the check engine light has started coming on every time I drive on the highway. At approximately the 5th mile of my ride, the light comes on but I cannot detect any symptoms, the car runs great. This rarely if ever happens when driving in the city, only on the interstate. My car is too old to be hooked up to the fancy diagnostic machine. What I should check to resolve this problem? 1995 Honda Odyssey with 279,000+.....
View 11 Replies
I have a 1995 BMW 525i and the fuse for the AC keeps blowing after a few minutes. It's #9 in the fuse box. Before the fuse blows the AC works fine. I can't find any visible problems. Is there a common problem that I can check?
View 1 Replies
1995 Ford 4.0 ... All the following have been replaced on the truck.
High Pressure Fuel Pump and assembly
Idle Air Control Valve
Spark Plugs
Oxygen sensor (Bank 1 sensor 1 Oxygen)
Fuel Filter
The most recent item that I replaced is:
Coil Pack
Spark Plug Wires
Now, with the Coil Pack replacement, the truck drives good, as long as I do not floor it (After it heats up, about 15 minutes). Basically, if I try to pass someone, the truck acts as if it is chocking out, like it is not getting any fuel.
Before replacing the Coil Pack. It would chock out at any given time, rather just barely pressing the gas peddle, or just sitting idle.
I took it to a friends muffler shop, and he stated that it is not the exhaust that is causing the issue. I am at a loss. Is there anything else that I can check?
The truck seems to drive fine, as long as I do not get down on it, and try to take off fast after it heats up. When it is cold, I can take off like a bat out of hell, and it runs like no-ones business.
View 14 Replies
I have a 95 Ranger that when warmed up completely will buck when I let off of the gas. It is a 5 speed and this problem really only happens in 3rd gear and also have noticed it doesn't happen in 4WD. When the engine is cold and I am driving and let off the gas, the truck coasts smooth as silk and as it warms up, there becomes a louder thump when the gas is let off.
It will not do it all the time and it really only happens in third gear at low RPM's coming to a stop. I can give it gas and it picks right back up normally, so I doubt it is a misfire. Also since the truck is a 95 I do not have any CEL indicators, nor is there even a CEL light built into the dash in the truck. It isn't a huge issue because I am used to it and can drive it accordingly without having a problem.
View 13 Replies
I am having an engine issue with my 1995 Ranger with a 2.3L. I have been having a P0340 code that kept appearing after several attempts at resetting the PCM. I gave up and took it to a Ford dealer for diagnostics and they called the CPS bad. They changed it, but the CEL light immediately came on with the code still kept coming up. The service rep. showed me the old sensor, it had a spot on the head of it where it looked like something was rubbing it. I'm assuming it's slightly rubbing on the gear it points to, which is the oil pump gear, correct? The truck runs fine, no performance issues whatsoever. Is it possible my oil pump shaft has developed play in it's shaft, causing this?
View 1 Replies
Had the top half of the intake off (2.3L) and fixed some vacuum leaks and replaced a power steering pump. Started truck and it ran funny like missing on one cylinder then cleared up then started making a loud knocking noise and running rough. Assumed that it swallowed something when I had the intake off and it got into a valve or into the cylinder. I pulled the plugs and there are no obvious signs of a problem. I also did a compression test and all 4 were around 150psi.
Put the plugs back in and started it and the same noise was there. Removed the serpent belt just in case it was power steering pump related and the noise was still there when I started the truck. Sounds like something is inside the engine still. Going to get a friends bore scope to check further. I guess I will split the manifold again and run the scope in there. Pending that I may also look down the plug holes with the scope. This is a major bummer. Not what I needed.
View 14 Replies
Have a 1995 F150 with 83k with manual locking hubs. Haven't used them in almost a year. Today turned them to LOCK, normally very stiff, but this time easily turned with two fingers. Front wheels would not engage. Local mechanic put it on a lift, manually switched each hub from LOCK to FREE several times and they work fine now.
View 2 Replies
I have a 1995 Ford Ranger 4 cylinder and the other day on my way home all of a sudden sounded like a lawnmower, it was very sluggish and would take twice as long to get moving,it also smelled like gas and I used a quarter of a tank in about 24 miles. Someone said it could be the ignition coils...
View 5 Replies
I have a 95 4.0 EFI inside of my 83 Ranger. Once the motor warms up, it starts to have an idle issue. I have to press the gas, in order for it not to cut off. Here is a video I posted a while back. A person suggested that it could be the MAF needed to be cleaned. I did that, and it did not work.
View 9 Replies
My Father in Law's 95 Ranger, 4 Cylinder, 5 Speed has started acting strange. It has, in the past 3 weeks just died suddenly, and won't restart. No action at all when you turn the key, as if the battery is disconnected. Wait for 45 minutes to an hour, and it starts back up again.
He has had it to a local shop twice, and the only thing they have done is let it idle for 5 hours at the shop. Of course, it never stopped.
Now they are saying it is the clutch, and depending on the type of clutch, (big or small).
I've been working on cars most of my life, and even had an 87 Ranger, and I've gotta call BS on this. He says it happens mostly when coming to a stop.
View 4 Replies
. I'm going to FINALLY change the tranny fluid in my 95 Ranger Splash this weekend and need all the feedback I can get! It's a manual trans with miles shy of the 250,000 mark...still on the original stuff!! I'm only the 2nd owner but I bought the truck with just 45,000 miles on her so I'm willing to bet the farm that it's never been changed. It's getting harder to shift from 1st to 2nd and I'm getting a little bit of grinding from 3rd to 4th if I shift too fast. Reading all the threads everywhere online, so many different people have so many different theories from stock Mercon V to MOTOR OIL??? The motor oil thing floored me but I understand the viscosity difference between hydraulic fluid and lubricating oil. figure out what the best thing to replace the original with to prolong the life of this long running wonder vehicle!
View 5 Replies