I have an '01 Dodge Ram 1500 that will not go into reverse while the truck is running. The hydraulic clutch and transmission fluid levels are good.
View 1 RepliesI have a 2004 Dodge Ram 1500, 5 speed manual with 110k miles. This past winter, the truck has started to whine when it's in reverse. The strange thing is that it also whines when it's in neutral and simply rolling backwards. It's intermittent, which is why I've been hesitant to take it to a shop to have them waste a bunch of time with it and say they can't reproduce it. Things that make it more likely to occur -- the truck being cold (IE: shortly after a start), air temperature being cold, when it's in 4WD. When I brake, it stops immediately. If I have the clutch on the floor or the transmission in neutral, it will keep doing it, as long as it's rolling backwards. This never happens in any forward gear, and it's been happening intermittently for a few months now. I had the transmission fluid changed this past fall, sometime before I noticed it started happening.
View 3 RepliesMy truck is skipping but if I give it more throttle it will stop but then will start back when I let off the throttle. It seems like it is only running on half the cylinders. This problem is intermittent which makes it very hard to troubleshoot even for the dealership and other places I have taken it. Also, the problem is temperature sensitive. It only does it below 40 deg. F. Truck runs fine any other time of the year. Truck has new plugs, plug wires, distributor, egr valve, O2 sensor. Also, the IAC has been cleaned. The check engine light does not come on.
View 14 RepliesMy name is Jason and I have a 2001 Dodge Ram 1500 with an automatic transmission. It has trouble shifting. I have to drop it down from D into 2 and then back into D to get it to shift out of second gear most of the time. If I have to stop ten times in a trip I have to manually shift it about seven or eight of those times. On top of that, sometimes while I'm driving it will slip into Neutral but it'll still be in the D position. This just started and has only happened a few times so far. My transmission fluid levels are fine. I'm trying to see if there is any other solution besides rebuilding or replacing my transmission.
View 2 RepliesThe truck will go into reverse, but will not go into drive or any of the other gears. When shifted into one of those gears, it just idles as though in neutral. This started as I was driving down the highway at approximate 70mph. The speedometer jumped up then fell to zero as the car slowed to a stop. There was no noise except the sound of rapid fuel intake and then it went to idling. I have been told it may be a speed sensor, but I was wondering if there was anyway to confirm that before I have the truck towed down to a mechanic and find out its more than I want to pay to fix it.
View 1 RepliesI have a 2001 Chevy Silverado with the 4.8L V-8 engine. It acts like it is running out of gas ( the gas tank is over half full). The truck has sat for about 6 months in this condition without being started here in Sacramento, CA. I then replaced the fuel filter and for a few minutes it started and the engine ran fine (without actually driving it). A few days later I started it again and it now again acts like it has fuel starvation, it will rev up briefly then act like it is running out of fuel. I know the fuel pumps are the Achilles Heel of these trucks, but before I try changing it I was wondering if there might perhaps be another problem such as the new fuel filter plugging up quickly or possibly an electrical problem. I've always heard these fuel pumps either work or they don't work, nothing in between. This problem is intermittent but big enough the truck is not driveable. Is there any way to get a good take on the problem before diving into the fuel pump replacement and hoping that solves the problem ?
View 5 Replieswe had a shop replace a thermostat in oct 10, last week our truck started running hot so we put in about 3 qt of 50/50 coolant. it returned to normal temp the next day we noticed some foam coming out of the overflow. when we opened the hood it looked like a brownish/red color and is a thick foam. When taking it back to the garage they cannot tell what it is. They have tried to flush it out and say they put in 3qt of fluid and only get out 1qt. It can be chunky at times. What it could be?
View 1 RepliesI am trying to get some advice on a diagnosis for a transmission problem i'm experiencing with my vehicle? It's a manual transmission and the sound i am hearing is when i shift gears is a loud whirling grinding sound. It's really loud in 2nd 3rd and 5th and doesn't stop.
View 1 RepliesMy truck does not go into reverse but thinks all positions of shifter are drive. I had some slippage and changed the filter and oil great for awhile then blame no reverse just forward I was told my torque converter was out I just don't know....
View 1 RepliesI recently installed a rebuilt engine on a 1997 Chev. s10, 5 speed. Decided to replace the clutch & pressure plate also. After bleeding the save cylinder several times, I could not get the transmissions to go into gear while the truck was running, although it would shift in all gears with truck engine off. I took transmission out again and replace the slave cylinder/throw out bearing. After bleeding 3 times I now have a full clutch, best ever, but still will not go into gear with engine running. It worked perfectly before replacing the engine.
View 5 RepliesI have a 2000 dakota in the morning after the first start, moving foward the truck rocks and feels like trans. slipping. After 5 mins, just fine. Change the Trans. Ffilter?
View 1 RepliesChasing down a grinding noise. I have done a lot of research but nothing quit matches up with what I am hearing.
I have a 1979 F250 4x4. A few days ago I put the truck in reverse and as I was backing up it was like the drivetrain locked up. After that I put the truck in gear and started on my way. As I got up in speed a pretty loud grinding noise was coming from the tranny. 2nd and 3rd gear aren't bad but when I get up to 40+mph it sounds like crap. If I push in the clutch the grinding is still there. While driving I also put the transfer case in neutral, kept the tranny in gear, pushed in the clutch and the grinding stopped.
I also took the lid off, inspected the forks and thoroughly cleaned the inside but noise still continues.
Just finished putting a fresh 460 backed by a (1977) c6 in my '68 ranger and now I'm having (what I believe is) transmission problems. The truck will idle and rev properly in gear but as soon as I put it in drive or reverse the RPM's drop and it dies. I jacked the back end up and put it in both drive and reverse and the tire's spin, but if I try and apply the brake to stop them the truck will die. My suspicion is that the torque converter is locked up all the time. I have managed to get it in gear and give it gas and it'll drive and shift fine, until I come to a stop. My question, what would cause the converter to do this? It's the same transmission and converter that I pulled out a month ago and I never had any issues before...
View 4 RepliesFriend lost reverse and truck shakes at 35 and above seems like it needs a new transmission. What years are a match for this transmission and any other models trans match?
View 2 RepliesI am using my son's truck this week, 2012 F250, 120,000 miles or so. I left it running in the drive while I got something from inside the house. Guess it was idling approximately 10 minutes. When I put it in reverse the transmission would not shift and the truck didn't move. I killed it, re-cranked it and it went in reverse.
As I was driving down the road the transmission would change gears up and down for no reason. I stopped the truck, and put it in park. I would put it in drive and the transmission sounded like it wanted to slip. I put it back in park and the transmission would not engage. I then killed the truck, re-cranked it, and it drove fine for awhile and started doing it again,
I kill the truck, re-crank it, and we go down the road.
I have a 2001 m5r2 ford f-150 standard transmission. i have replaced the slave cyl., the entire clutch assy., the master cyl. pilot bearing. the trans. will engage all five gears plus reverse while truck is off but will not engage a gear while running. i have bled and bled and bled and still will not engage.
View 1 RepliesI just purchased a 2001 Dodge Durango 4wd with 140,xxx miles on it. My issue is that whenever I accelerate it hesistates and if I am going at a high speed like on the interstate or expressway it sometimes slows down (drastically) if I'm going uphill. What can be causing this?
View 6 Replies1991 4x4 f250 idi w e4od w 3:55 ratio... The truck is slow to engage in reverse, about 5-10 sec. It also has a very hard shift 1-2. All other shift points are good. Drop down is good, and TC lock up happens at all the right points (feels like anyway).
I've had the truck for about 2 years now, replaced several sensors an harnesses and a full fluid change to solve other problems but this still remains.
Sometimes when I start it in the morning if I let it sit and idle for a few min it will engage reverse much quicker AND shifts way smoother and constant. Shifts smoothly thro all gears, holding a constant 1800-2000 rpms with no drop or lug. Or do I need a rebuild?
My 2001 Dodge Durango has an intermittent clunking that seems to correlate to the wheels rotating and happens: at low speeds (0-5 mph)... however, it has gotten worse if I drive continuously for an hour and then stop. It will happen between 0 and 30mph and be much louder.
When the clunking happens, the steering wheel also rotates to to the right and the car will shake a little.
If I had to guess, the clunking is coming from the front left but really could be anywhere.
I have taken it to FireStone multiple times, they have test driven it all over... it never seems to happen when they have it.
I bought late 98 F-250, 5.4 G, 4WD. OHad to replace the steering flange because they messed up the ignition cylinder and flange. Truck didn't run for 4 years. 249K miles, no history available. Got the engine running, no DTCs. D, 3, 2, 1 barely moved the truck forward but, R hauled butt in reverse. Checked transmission fluid it was good and clean.
Came back to it a few days later it threw a P0720 (output speed sensor circuit) and I have no reverse, park feels like it wants to move, R is neutral, N is forward, D is forward, 3 is forward, 2 is forward, 1 is forward. The N is full drive. I cleared the P0720 code after it came up and it has not returned. The instrument gauges work but the odometer display is intermittent. Linkage? Fluid? Sensor? Wires?
2001 Santa Fe 2.7L 4wd ... In December I bought this vehicle it only has 95K on it. When I drove the car home I noticed it needed brakes so I put brand new pads and rotors on the whole way around. I changed the oil, air filter, wiper blades, and made sure all fluids were good. I had the front spring recall done and also put some new sway bar end links on the front. The car runs fine and I am rather impressed with it. It does have some rust but I'm not to worried about that. This isn't my everyday car just a winter/extra car. Recently I have been getting some clunking only when going from reverse to drive and going slow. You get a clunk..clunk pause clunk..clunk almost like you have a flat but once I get the car up to speed it is fine and you never hear it again until the car sits a day or so and then it will do it again. I don't know if I have a differential problem or a u joint or maybe something with the e brake or rear brakes? but it is -3 right now outside and I would rather know where to start so that when I can take a look at it I know some things to check or what it might be.
View 3 Replies