1995 Chevy 1500 With 5.7 Engine - Truck Completely Stalls Out And Has No Power
Aug 3, 2015
I own a 95 chevy 1500 with a 5.7 engine. The other day I'm driving home and my truck completely stalls out and has no power what so ever. To be more specific I didn't have lights, radio, key buzz nothing. Well by the time I got the under the hood I had power again and it cranked right up. I put it in drive and 5 minutes down the road and it stalls again with no power what so ever. I've been having problems recently with it stalling at stop signs/red lights but never with a loss of electrical systems. What this could be?
View 3 Replies
Advertisement
Last week my truck started to stall a little bit. As I drove it a little longer, it stalled all the way out. It started back up fine but when I gave it some gas, it cut off. This happened several times. I popped the hood and noticed the throttle body was a little loose. Thinking air may have gotten into the system,I tightened it back up. I started it up,put it in gear and it seemed to drive fine and it started stalling again.
While I was on the interstate, it would cut off, cut back on,cut off and then cut back on. Finally it completely stalled out. I had to have it towed to my house. I hooked my code scanner up to it and it through code 44 (O2 sensor) and code 54 (Fuel pump relay or something like that). What could be causing my truck to run this way.
View 14 Replies
I have a 1995 k1500 when I turn the key on no lights on the dash if I wait 5-10 second you hear a click sound in steering column and the dash lights come on and starts fine. ???
View 1 Replies
Several years ago I had to replace the fuel pump - truck had about 100,000 miles. Within the last 4 - 5 months I have replaced the fuel pump twice and just today (about two months since the last replacement), the fuel pump has failed again. That has been the pattern now for the last several months. I have had the work done by one of the reputable car repair shops in town - they have also done work on my 2004 Impala with no issues with the repair. There must be something else going on besides just the fuel pump going bad. What would cause so many fuel pump failures.
View 16 Replies
My 1995 chevy c1500 cuts out at idle or the moment the brakes are applied to shift into drive. I replaced the passenger wheel cylinder and bled the brakes and it ran fine for a few hours, then the idle problem stated again. I have check the map senor and a few other electronic component as my mechanic said the problem " might be electrical."
View 6 Replies
I have a 1996 Chevy Cheyenne pickup with a fuel injected small block that has 50k miles. Earlier this summer the truck developed a problem where it is very hard to start when cold (after sitting overnight or after sitting for many hours on my flat driveway). When the engine is cold (say the first start of the day) I can only get it to start by giving small bursts of cranking power to the starter. That is, it won’t start if I hold the key in the cranking position but is more likely to start if I give it a short burst of cranking power (when I hold the key in “start” position) for a second or two.After the first start of the day, the engine runs fine and subsequent starts are quick and normal. The “Check Engine” light is not on and there are no trouble codes…. Other than hard starting there are no issues with engine performance.
View 2 Replies
My 1995 Chevy Silverado 1-ton diesel stalls with no warning at various times while driving, such as at intersections, on the freeway, coasting, idling. It may go days or weeks without doing it, then all of a sudden stall eight times in one day. My husband says it has sediment, such as rust, in the fuel tank causing it to clog the fuel line. We've replaced the fuel filter twice, and we keep the tank topped off with gas, but it still does this out of the blue at times. I no longer trust the vehicle and will not haul the horse trailer using it, which is why I have the vehicle in the first place. By the way, the problem began after the truck sat for several cold winter months due to drained batteries. After we replaced the batteries to get it running again, it began stalling like this on a semi-regular basis. If it is rust or sediment in the fuel tank, what can we do to fix that? Could it be something else causing the problem?
View 2 Replies
A week ago, driving home, the tech started to drop quickly to zero then recover, like the ignition was turned off and then back on. I was able to make it home. The car was due a tune up. I replaced the crank position sensor (OEM), replaced sparkplugs (Autolite Iridium), air filter, fuel filter, no luck. I ohmed the coil packs, secondary resistance showed good, replaced the ignition control module (aftermarket). After this, engine would stall after it was at temp, could restart, once put in gear it would stall, but I could go in reverse and drive home backwards.
Reinstalled original OEM ignition control module. Towed to GM Dealership, mechanic said fuel pump was bad, ignition wires needed replaced, one injector ohmed bad. I took car home, replaced fuel pump (OEM), ignition wires (OEM), no luck. Removed plenum, found pcv valve clogged, and hose kinked, replaced both, ohmed all 6 injectors, 5 injectors read 12.3 ohms, 1 injector was 11.6. Replaced all 6 injectors, (Napa), plenum gasket, still same problem.
GM dealership said computer said no data, they though perhaps ignition control module was bad, but I don't think so. I hooked up my Actron shorting plug, reads code 12 which means no faults, no other codes. I noticed EGR valve has a lot of carbon in the hole, thought about changing it, but I'm really not sure where to go now. The car is a 1994 Chevy Lumina with 230,000 miles, spent about $500 the last week doing brakes, and trying to fix this engine. Where to go from here.
View 5 Replies
My daughter has a 1995 Grand Prix - 3.1. The car has an intermittent problem that can go 2-3 weeks in between occurrences.
It runs like a top, but will suddenly lose power while driving and die completely. After a while it'll be fine. (starts up again.)
The lights will flicker and give a bit of warning before it dies. I had both crankshaft sensors replaced a month ago and I though that would do the trick.
View 3 Replies
I have a 95 chevy silverado. 305 with an automatic transmission. I was driving down the street at about 30mph when the power went out on me.
The engine stayed on and all lights stayed on. I could rev the engine but the truck wouldn't move.
I then had a friend tow to my house and i let it sit overnight trying to decide what to do next.
The next day I went out and started it and it and was able to drive it again for a short distance at low speed and then it did the same thing again.
View 5 Replies
I have an 88 chevy K-1500 4x4 5.7L ... My truck lacks serious power, it idles rough, sometimes wont idle at all, sometimes Truck Idles fine. I have adjusted the timing to tdc, and 4 deg. both ways still runs like crap.. Sometimes I can keep it idleing, put it in rev. or drive, and it will die. I have no power and if I put my foot in it too much it will backfire. but will only backfires when in gear and press on the gas to put a load on the motor. I have replaced the: tps, map, egr, pcv, distributor, cap, ignition coil, rotor, plugs, wires, timing chain, both sprockets cam and crank, checked all hoses for leaks, replaced the injectors, the O2 sensor and have changed the intake gaskets. And am still having no luck...... I am bout to just drop an M80 in the gas tank and watch her burn..
View 14 Replies
I have a 1995 GMC Sanoma, 2.2 Lt, 4 cyl, 5 spd. It has about 130K miles. Each day I drive it back and forth to work (about 30 miles one way). About 6 months ago I noticed that at about 5 miles into my drive to work it would stutter but then catch itself and go on the rest of the way with no problems. On the drive home it would do the same thing at about 8 miles into the drive. This didn't really bother me until one day instead of stuttering it stalled but I could restart it right away while coasting. It had steadily gotten worse to where I had to pull over on the side of the road and restart because it wouldn't restart right away. Nowadays I hardly drive it at all because I'm afraid it will stall and not restart at all. I have replaced the air idle control, fuel pump relay and the positive battery cable. The symptons now are basically the same but different, I can start it (anytime, morning or evening) and it will idle fine for about 5-10 minutes. It will then start to stutter and try to catch itself, the idle will then rev up to about 1500 and then come back down and stutter some more before stalling. After that it will not start back up until maybe 10 minutes after, (it acts like it is not getting any fuel) but once it starts it runs fine, I drove it around for about 20 miles and it ran real strong. The next day it went through this same cycle again.
View 1 Replies
1995 Camry 2.2 4cyl 165,000 miles FED (not CA).
Two days ago while doing a routine oil change I noticed my kids engine compartment was real dirty as we had alot of flooding from rain a few weeks ago. I sprayed the engine with a water hose w/nozzle to clean it. At the time I didn't know any better. The car was driven without any issue briefly that day. The following morning the car was driven a distance of 25 miles without incident.
After resting 30 minutes the car was started and began to idle rough and stalled repeatedly. When I showed up to inspect the issue it had been sitting about an hour. I went for a test drive and the car ran good. About 20 minutes later iI get another call saying the car is doing it again. It was sputtering/ hesitating when I attempted to accelerate it began to stall unless I limped it along staying off the gas.
Once I got it home I started doing some research and discovered that my spraying water in the engine compartment was probably what caused the issues I was experiencing. So I began to go through the motions trying to repair. I also noticed the car ran good when cold but at operating temp it would run rough. The check engine light has not come on.
I replaced the spark plugs, plug wires, distributor cap & rotor, etc... sensor, and air filter, I cleaned the throttle body port and IAC valve port with sea foam cleaner. I cleaned and tested the EGR valve & ports. Nothing has improved from my efforts.
I must of screwed something up good, since its been 2 days, it should be dry by now. I also been thinking that maybe some water got to the injectors. NOt sure if a cause, but the oil was changed right before I sprayed engine.
My course of action as of right now is.
1.Check and clean all electrical connectors
2.Replace distributor with a re-manufactured one
3.Replace upstream o2 sensor
View 13 Replies
I am doing a side job and this thing has a rough idle. I put the scanner on it and pulled code 43 ESC and a ritch and lean code from the O2 sensors. I know the O2 codes are probably from running rough. It has been a while but could the knock sen be the problem or the ESC itself? I looked for the ESC by the throttle body but didn't see it. I remember what they look like but this is a late model 94 are they some where else?
View 4 Replies
My truck is skipping but if I give it more throttle it will stop but then will start back when I let off the throttle. It seems like it is only running on half the cylinders. This problem is intermittent which makes it very hard to troubleshoot even for the dealership and other places I have taken it. Also, the problem is temperature sensitive. It only does it below 40 deg. F. Truck runs fine any other time of the year. Truck has new plugs, plug wires, distributor, egr valve, O2 sensor. Also, the IAC has been cleaned. The check engine light does not come on.
View 14 Replies
Last night transmission in my beloved '89 Caprice Wagon let go, it slips completely in all the forward gears. I was coming down a long hill using low gear for several minutes and when I put it back into OD at the bottom it seemed to skip a little but it was still making power well enough. I got off the freeway at my exit and stopped at a red light, when the light changed I was revving high but barely creeping through the intersection. I pulled over and this is what I figured out:-All the forward gears make essentially no power any more.-Reverse seems to work normally.-The fluid is at a normal level and not discolored or burnt smelling.
I don't know if this is related or just an amazing coincidence but the water pump also seems to have blown the gasket at the same time. I must have just happened within a few minutes of me pulling over because there was still a ton of coolant left and the temp was still in the normal range. I don't see how they're related but, like I said, the timing is too coincidental. Earlier this week but just a few miles ago I also topped the power steering fluid and oil.
It's a 200-R4 transmission, is it toast? Why does reverse work but all the forward gears slip completely? Is the water pump just a red herring? I did drive the rest of the way home in reverse.
View 8 Replies
Very weird thing happened on the way home from work. When I left work (not to full temp) at about 1500 rpm and 30 mph (had to be at 30mph--seemed to be the key) the whole truck felt like it was rolling across rumple strips (the ones one the shoulder of the road) all vitals were normal and it was gone once on the interstate and up to temp (I did gon on it to blow out anything that may have needed to be) it felt more like drive line but honestly can't say. 2006 F350 4X4 ....
View 7 Replies
I got this truck from my step father, drove it from mississippi to washington (state) with minor problems. It's been sitting in my driveway for the last 6 months and I probably drive it once a week. I loaned it to my sister-in-law and she drove it for a couple of days with no problems. She went out one morning to take it and it wouldn't start, just cranked it for a few minutes and gave up. To make a long story even longer, I though it was fuel so I checked the pump, changed the filter, drained some fuel thinking water might have gotten in, ... to no success. I then started looking at electrical. Spark was getting to at least one plug. Pulled the distributor cap and cleaned it all up, replaced all the plug wires, and then tried starting it with the same results. (Oh, by the way, no check engine light so I assume no codes).
This goes on for a couple of weeks as it's in the driveway and I only pop the hood when it's not raining (we live just outside of Seattle). The other day I have the hood open, my wife decides to check on me since she thinks I'm talking to God and is wondering why I would use that kind of language when address a diety. I ask her to jump in and crank it while I pull a plug wire to see if I'm getting spark....again. Low and behold, the truck starts right up. I jump in to see if it's throwing a code and nothing. The thing is running great. I did notice that there is a ticking coming from the engine compartment and I realize the plug wire is still disconnected so I turn it off (with much hesitation) connect the wire, go back inside to start it and the thing won't start. I'm a private pilot and they say, if you're flying along and you do something and the engine stops, undo what you just did. So, I go back out, unplug the spark plug wire, and the thing starts right up. So, I start thinking, try another plug wire. I reconnect it, try another, and it won't start. So, what I figure is that it will only run when the second to the front cylinder plug wire on the drivers side on the engine is disconnected.
View 7 Replies
can i adjust idle on car, seems to be running faster without using gas pedal.
View 2 Replies
I have a 92 chevy pick up 5.7 with 159,000 miles. The truck runs and starts great but shortly after I bought it 3 years ago it developed a sort of misfire at higher rpm's, it's fine if I drive it normally but if I try to pass someone it will downshift then fall on it's face, (spit,sputter and slow down). some times I can feather the accelerator and it will come back again. I normally don't drive the truck in the winter but this week I was forced to use it and the cold weather is seriously affecting it, it took forever to get it up to 70 mph after getting on the highway. once up to speed it will do 75 all day without an issue.
I've replaced the plugs, wires, pulled the throttle body and cleaned it as the port for the pcv valve was plugged solid with carbon. I have not replaced the cap and rotor as they seemed to look fine. I have not checked the fuel pressure because it will break the tires loose upon take off and I don't think that would be possible if the pressure was low, would it?
View 5 Replies
I am trying to get some advice on a diagnosis for a transmission problem i'm experiencing with my vehicle? It's a manual transmission and the sound i am hearing is when i shift gears is a loud whirling grinding sound. It's really loud in 2nd 3rd and 5th and doesn't stop.
View 1 Replies
