1992 Blazer 4.3 S10 - Rough Idle Cold
Jan 6, 2014
I've got an "on- and off-going" problem with my '92 S10 Blazer.
Car specs:
Year 1992
Blazer S10 4.3 Tbi
4- doors 4WD
Mileage 200k miles
Symptoms:
As cold, every now and then it will start right up, but the idle is wery rough, and seems like its running on less than 6 cylinders. When giving gas, it revs up, but runs roughly and still seems to be running on less than 6. Won't stall though.
When engine warms up after a couple of minutes, the idle gets smooth and no issues what ever when driving.
So just to be clear, this issue is so far only happening when staring cold.
Parts (new off course) changed recently (less than 500miles on them):
Distributor
Spark plugs + wires
Alternator
Battery
IAC valve
Fuel filter
This symptom came up now and then before changing any parts. I am quite handy with cars (pure amateur though), but can't really afford solving the proble by changing loads of parts with no effect..
View 4 Replies
Advertisement
1992 S10 Blazer, 4.3L, 4x4, TBI "Z"
When I start the truck, it idles rough, like it's idling too low, and even feels like it's missing during idle. Sometimes when I put it in gear (reverse or drive), it shuts off. No codes are being thrown. It has no problems driving around town or on the highway. It's just that initial start and idle.
I've checked all the following with a shop manual:
Ignition Control Mod.- Orig and 2nd one from junk yard. Both tested good at store. Even the testing in the shop manual with an ohm meter and battery tested good.
Ignition coil- tested good using shop manual testing
TPS- Scan shows .2-.7 at idle.
Plugs, wires, cap, and rotor are good.
Vacuum is good.
Haven't checked IAC, EGR
I recently moved cross country, and about halfway through, I broke down. Engine would turn over, fuel relay would click, injectors would work, but no fuel. Pulled it in to a truck shop, and after all my testing and theirs, we determined it was the fuel pump. After they had to fix a pinched hose, it ran. I made it to Texas. I didn't have the idle issues prior to the trip. Just had the tranny rebuilt and everything was great.
I thought, at first, the ignition control mod was the problem because it got a bit warm pulling the trailer, and I know those things don't like too much heat. No dice. So, what controls idle at Park and in gear but at idle? EGR, IAC?
I did a WinALDL scan. IAC at Park/Idle ranges from 18-55. The engine never runs in Open Loop. I would say the engine runs mostly rich according to the scan. I've attached a manageable version of the WinALDL data.
Also, I need to check the thermostat or temp sensor. Scan reads the engine never getting higher than 180.
View 4 Replies
I have a 1998 chevy blazer about 134000 miles v6 4.3 4wd.. This last two weeks my blazer been running rough. I like to know what is normal idle for that blazer. When at idle its 500- 550 rpm when in drive its 500rpm.
View 16 Replies
Think i have an exhaust leak in a 1999 s10 blazer lt 4x4 4 door. the loudest spot where i can hear the exhaust noise at cold start and idle, is the passenger side right behind the front tire. on cold mornings where you can see the exhaust smoke prior to warming up i cannot see anything coming from this area. non mechanic types have suggested either the y pipe, or where the y pipe meets the header. Would both have to be replaced to fix this problem if this is the case? and how intensive is this to fix? meaning would the whole motor have to be pulled to remove the entire exhaust piping to have it brazed? my dad is a mechanic, so the tools I've got and his know-how, just need to know what to do? Any definitive way to tell where an exhaust leak is, beyond having a friend cup their hand over the tail pipe, while they look for it..
View 3 Replies
I have a 1994 chev Blazer S 10. that has thesy troubles. when it warms up it runs high and hot exhaust and ruff idle. with a hot cat. Replaced EGR carbon build up at times.replaced fuel pump, and all the senors under the hood. Still runs the same.
View 3 Replies
What would cause my truck to have a long turnover start, a really rough idle, and a loss of power after idling at a stop light for about a minute?
This problem gets worse as the truck warms up. It feels as if I'm not getting power from all 6 cylinders but this goes away after about 20 feet of acceleration. The truck has never not started. It just has to turn over for about 5 to 10 seconds before it fires up. I changed the spark plugs and wires thinking it was that and then i tried the fuel filter and it wasn't that either.
View 8 Replies
I just bought a 92 Toyota Celica for something to play around with. It's got just over 200,000 miles and everything seems to run alright except there is a really rough vibration at idle. The vibration is so bad that it's almost visible. You can still feel the vibration in drive but it isn't nearly as bad.
Any clue at what could be causing the vibration? I'll try to get a sound clip or video uploaded ....
View 5 Replies
I have been having some recent issues with my 92 bird lately. It started minor but now the car will not stay on. It originally started out as I would need to press the gas to get it to start and it would stay on, but now if I let my foot off the gas for anything it will just idle rough and die out. I took it into a shop and they said that I had a bad idle control valve and the pigtails need to be replaced. They also said that some wires were shorted out and they would replace those as well. They replaced the Pigtails and the idle control valve and the car started to work fine again, for about 4 days only. I drove to the store and when I came back out to start it back up it wouldn’t stay on unless I gave it gas.
I had to drive it home giving it gas and using my other foot on the brake so that it didn’t due out. I checked the job they did and doesn’t even look like they did what they said they did. I looked at the botched shrink tube job they did and it just doesn’t look that professionally done. I did call the guy and he gave me an excuse and said that they short must have traveled further and he was surprised that the car was even running when they were done. I of course just hung up the phone after hearing that. I did a little looking around the engine and I noticed that if you unplug a vacuum tube and press on the gas and hold it at 2000 rpm for a few seconds and let off the car will stay on, but the moment I plug that hose back up with my finger or plug it back in the tube slot, the car idles rough for a few moments and dies.
View 6 Replies
I have a 92' Century w/107 K miles that has a medium rough idle. This is a summer use vehicle for me. I have done the normal maintenance on this motor w/ new plugs and a good Napa wire set. Any bad vacume lines that I can get at have been replaced including the vacume tree on top of the motor. Has anybody had coil issues or ground issues with this motor?
View 2 Replies
1992, shory 3.0 130K MILES
On start up runs very rough, will stall if not power braked or revd a little on start up/out of the driveway.
VOLT METER STARTS GOING NUTS!!
After a mile/warm up,,, runs great. But sometimes even when its hot, it will still try to do the rough idle briefly after just a few minutes restart. Give it a few revs at that point and its good. And once in a blue moon it will do it randomly at a stop light,, out of the blue. Very rare
View 12 Replies
Since having my engine replaced with a newer used engine block my idle speed when I first start it up or when it is cold is around 2000rpm which lasts for about 2-3 minutes until it begins to fall to the normal range of 1200-1400 and finally to 850 or 900rpm when warm. how can I fix this or is it okay to idle at 2000rpm for a couple of minutes? is it hurting anything?
View 3 Replies
I replaced my engine that had 155,000 miles with a newer used one with about 30,000 miles. since the swap my gas mileage is down by one third or more. Everything else seems fine except that my cold start idle is up to 2000rpm's until it drops to normal within 3 minutes.
View 2 Replies
I noticed a drip on the remote oil filter adapter connecting block, it was appearing from the seam between the block with the supply and return lines to the oil filter and the engine adapter. I purchased a gasket set and replaced the two O rings, the old ones were hard and flat. The new ones are soft and round, I thought that would stop the seep, but there was no change. So after removing a few more times and cleaning, even substituting a slightly different size O ring with no change in the drip. The two aluminum blocks are held together by a 13 mm bolt. It is a 1992 S-10 Blazer 4WD 4.3L. None of the crimps are leaking.
View 3 Replies
My 1.8t is very rough at idle when cold, smooths out when over 1000 rpm and when at normal operating temperature. Code reader says 171 and misfires.
View 6 Replies
If my car's been sitting - say monday morning after sitting all weekend in the garage- it runs rough for a little while. Sometimes only for a few seconds, sometimes for a little while after the idle drops. The colder the car is, the longer and worse the condition. It feels like a cylinder isn't firing.
After a particularly cold and wet spell (I had the car outside) it ran so badly it threw a code for one of the cam position sensors and #4 misfire. I replaced both of the sensors. That worked a little.
Since I was due for 80k service and saw a misfire when damp, I replaced the ignition coils along with the spark plugs. That worked a little more. But, it still does it. What else could it be if not ignition? Sticky valve? something else?
View 3 Replies
I have a 2007 SF 2.7L V6 with 55000km.
Recently we have noticed that from a cold start the engine idles roughly few a short time and especially bad if put into gear only moments after starting.
Do we need to let it warm up for longer?
View 4 Replies
I have a 99 silverado with the 4.8 w/186k on the clock. I am having an issue with rough idle and hesitation on cold start up. Once the truck warms up the idle and hesitation go away. I have replaced the PCV valve hoping this fixed it, but it did not. I have also cleaned the TB and the MAF.
View 2 Replies
I have a 99 lesabre cold start rough idle but smooths out . Warm no start. Trouble codes P0171, P0300, P0336. Had plennum replaced 2 years ago but I'm seeing coolant around the base of the plennum so I'm going to have to do that again but I don't think that has anything to do with the warm no start.
View 14 Replies
My 2007 TrailBlazer with 84K stumbles for 25 seconds when I start up cold. After 25 seconds I hear a click and then it runs perfect. No engine codes present. Have new plugs, new O2 sensor, new thermostat.
View 5 Replies
I got the fuel pump and fuel pump control module replaced. Now I am still getting a cold start delay (5-10 seconds to start) and it has a rough idle sounding like its misfiring. This happened when i picked it up at the dealership after a new fuel pump BUT! keep in mind it has been doing this for a while so i figured it was the fuel pump.
New oem plugs and the coils were replaced when i bought the car because the coils failed during a test drive I need to scan the codes but i will post. Also this only happens during a cold start. if the car is warm and i go into target or something then start it shortly after its fine.
TSB'S I think will fix this. [URL] .....
View 3 Replies
Since my V6s very rough ride only occurred on cold mornings (fixed with a new driveshaft early this year), I wonder if some of the newer owners will be complaining of this problem soon, now that we're embarking on fall.
The symptom was strange. On cold mornings, between 30 and 50, the Touareg would feel as though it was riding on extremely rough pavement.... over 50 it was fine, and then, after about ten minutes of driving, it went away at all speeds.
View 7 Replies
