I have had everything related to the clutch changed, and I even had a dealership bleed the clutch line. The problem is the clutch pedal is soft and will sometimes work good and sometimes won't. If I prop the pedal to the floor for a few hours, it works fine for the day. what gives?
View 1 RepliesJust as the title states. When I put the AC on in the car my clutch pedal gets some play in it, enough that it messes up shifting and gets jerky. I tried searching, but no results
View 14 RepliesWe were headed home the clutch pedal went soft... Ok, I thought it's either the clutch master or slave. I get it home and replace the master and after bleeding I had good pedal feel.
Great I thought, I got lucky and it was only the master. Drive it around for a bit and get on the highway and just as I was about to downshift the pedal went flat to the floor again.
Well after pumping the pedal until it had good feel again I got it home and bleed it a couple more times just to make sure I got all the air out. Drove it again. Same thing, after a little while the pedal gets soft again.
Now before I go and replace the slave is it possible I have a faulty master? Having issues after replacing the master?
I keep finding air every time i bleed my clutch. I am not losing fluid but i can not figure out whats causing my problems. The pedal is soft at first and then gets harder and it sometimes needs pumped before i change gears or to even get into gear. I am afraid its the slave but i also just may have air in the system.
View 8 RepliesJust the other day I got the clutch replaced on my 06 WRX. I took it to a reputable workshop that I've dealt with before. When I got it back the clutch pedal feels very soft and goes to the floor with ease, whereas before it was a lot harder and felt good. It works good and dosen't slip but just a soft pedal. I also went for the OEM replacement and not aftermarket. Some of the google searches I've read say the pedal will get harder after about 1000-2000 km.
View 5 RepliesWe have a 1997 Mitsubishi Eclipse with a hydraulic clutch. The pedal is very soft in the morning and requires a good bit of pumping the pedal to get good pressure. I know the system needs to be bled. Does this mean one of the cylinders is bad? I have added a little bit of fluid over the last year- maybe 2 or 3 ounces total. Right now the fluid level seems fine but it still needs to be pumped before driving.
View 7 RepliesI have an Imola 20th and recently i have been having some problems with my clutch. The pedal goes from being soft to very hard when its close to disengaging. It also engages very heavily when I go to let it out. This only started happening recently when temperatures started to drop if this has any effect on a clutch. Also, I replaced a shift fork two months ago and was curious if there was possibly anything going on with seals around the slave cylinder.
View 2 RepliesI changed my oem clutch in my mk4 golf 2.0l with a stage 1 ecs tuning clutch kit. Lightweight flywheel, clutch disk, pressure plate and throw out bearing. But since I have my clutch pedal has been less stiff then usual. I like my clutch pedal as stiff as possible but it just isn't I bled off the slave cylinder. When I was done no air was coming out but it is still way to soft for me. What should I do next??
View 6 RepliesMy B6 purchased exactly three weeks ago has had a soft brake pedal since day one. By "soft," I mean that when parked with the engine running and applying moderate pedal pressure, the brake pedal provides some resistance but sinks to the floor. If I pump it up a few times, it temporarily gets much firmer, but eventually sinks to the floor again after a few seconds. Now the car so far has never failed to actually stop, and it can get into the ABS. But during an abrupt (okay...panic) stop last week, it did go to the floor while the car was still moving. That's when I decided that was enough and took it back to be serviced.
My expectation was that there was just a small amount of air in a line somewhere, and that they could bleed the system and fix it. That was my experience with my B5: it was very sensitive to the least little bit of air, and if it wasn't thoroughly bled after brake service the pedal often got mushy and could find the floor. But bleeding them always get the pedal back to normal. So the service advisor said that he "had the service manager drive [my car] and compare it to a new Passat [on the lot] and talked to "Quality Tech. Manager to confirm." And the confirmation was that my brake system is "working as designed." In short, they say the brakes are working properly and there is nothing to fix. So I have now picked up the car and it still does the same thing.
Now I can (and will) bleed the brakes on my own over the weekend. But I would like feedback from others as to whether or not their brake pedals regularly see the floor. I just can't see this being the way any hydraulic brake system should work..
My B5's clutch started not returning by itself when the really cold weather started. When it gets warmer it starts to spring back up. I called the dealership and the initial cost of looking at it takes me somewhat aback. I've already spent quite a bit on it last year. Reading some of the threads on other car models I've seen mention of clutch master/slave and fluids.
View 10 Replies2013 tdi 6mt. I am noticing that my clutch clicks when the pedal is depressed. it does not happen when I first start driving in the morning, but it seems that once the cabin is warmed slightly it starts then clicks each and every time. It is annoying and it appears to be related to the different temps outside vs the cabin. I did not notice it during summer or early fall but it is cold here now.
View 24 RepliesI have a co-worker that is having trouble with his 06 passat. He explained that the clutch pedal has no resistance and is on the floor. The dealer he took it to is saying he needs a new clutch and pressure plate claiming that the "pedal doesn't have pressure on it is because the clutch discs won't engage" which sounds backwards if you ask me. Anyway, what could this be? Where could we start tracking this down?
View 13 Replies2006 Passat, 6 speed manual,113,000 kms. Driving to work this morning and I noticed every few shifts that the clutch pedal rebounded slowly when released. Then in traffic stuck to the floor and I had to physically pry it back with the side of my foot. Worked fine for a few more shifts then same thing again.
View 4 RepliesFacts: 1999 Vw passat 1.8t
1 year ago, clutch pedal would not come up off the floor, no life in the pedal.
Problem: Clutch master cylinder, replaced.
6 months ago, clutch finally went bad. Took car to clutch shop, replaced clutch kit(found out after i payed that they only turned the dual-mass flywheel... ). Get car from clutch shop, the clutch pedal came up only 2-3 inches off the floor by itself but you could lift the pedal with your hand or foot, and it would come back up all the way, but it was life-less. It was not pulling fluid in. It was catching extremely low. I called the shop, they said that it was just because it was a new clutch and it would get better. I didn't believe them.
Two days ago, I got into my car and couldn't get it into gear. Clutch pedal would go down with the same amount of force as before. Took it back to the clutch shop and explained the history with the clutch master and then them doing the clutch kit. They said it wasn't bleeding properly and they're not sure if its going to have problems again. Car is working now, but I am concerned that it will have similar problems again.
The tech who fixed it said he pumped fluid into it extremely hard, and that's what made the pedal come up all the way (no longer stops 2 inches off the floor) and its going into gear just fine now. What the problem might have been? Block in the hydraulic lines? If this is the case, does forcing fluid through it fix it?
My clutch pedal went all the way to the floor. The engine was missing first and then that problem happened with the clutch. I had the car towed to my business, I checked it the other day and the pedal was up. The clutch still doesn't engage.
View 6 RepliesLast night I was driving home and decided to show off at a light. I punched it pretty hard, but it wasn't anything outrageous.. anyway, as soon as I shifted to second, my clutch pedal gave out and dropped to the floor without resistance. I coasted it to a gas station, luckily.. When I lifted my foot the pedal rose back slowly. I tried pumping the pedal, didn't work. I looked for leaks, but none were found. I turned it off, put it in first and tried starting it, and it turned over and jumped/jerked forward, a lot like it did right when I shifted into second and it went out. So I'm assuming that its not the entire clutch cause it wouldn't have engaged the engine. It's not a leak. pumping it didn't work so it's can't be a pressure issue.. what is going on? is it my master cylinder, or maybe my slave?
View 7 RepliesJust went to leave my apartment and I get at the first traffic light and put it into neutral. Light turns green and I try to put it into first and it won't let me... In fact I cannot shift into any gear while the car is started. Put the flashers on and I am stumped. There was also more resistance in the clutch pedal as soon as this happened.
I turned the car off and tried wiggling it into any gear. For some reason while the car is off I can put it into any gear. So I had to put the car in first gear and start it and limp it home. I had to rev the engine to about 2,800 - 3,000 RPMS in order to get the car to bite and take off. Shifting into any other gear while driving was a hassle and it felt like there was a lot of resistance.
Just did some quick Vwvortex recon and some people are saying that it is a broken pressure plate? Pressure plate welds itself to the clutch? Or possibly a throwout bearing? Also what Transmission is in a 2003 Passat 1.8T Engine code AWM.
1998 Passat 1.8T FWD. My clutch pedal is stuck to the floor and wont spring back up. I can't seem to find the little tank to check the clutch fluid. I have heard the it uses the same tank as the brake lines do, but the tank that holds the brake fluid is full. Can it be the slave cylinder is gone? or just got a air pocket in the line?
View 1 RepliesI replaced my MC, and still soft pedal, when I bench bleedI noticed that the screw in plugs to fit the tubes over it to bench bleed it, they both were loose and when I was bleeding it a lot air bubbles was goin thru the tubes, so I tighten the screws and belled it again this time I bleed it till no bubbles, installed the MC and we bleed the brakes, and still soft peddle, we are going o bleed again tomorrow. Were we supposed to bleed until the new fluid comes out? and if you can what is the best way to bleed the brakes?
View 6 RepliesI'm a fairly new owner, and the 89 gt I just bought came in very good shape. Yesterday the manual clutch just went completely soft. I felt this for about a week when I first purchased it, but only in first gear and it worked itself out and hadn't recurred since then. Now the clutch will not disengage. Gears move well when the car is off though. I noticed the clutch fluid was totally empty when I looked under the hood yesterday. Is this indicative of a bad master or slave cylinder? Or do I just need to bleed and refill the fluid? I love driving this car and want to again soon.
View 1 RepliesOver the past week I have noticed leaking brake fluid and after my STOP Brake failure light came on I topped off the brake fluid and it is down to a low level again. I also notice that the clutch pedal (manual) does not return all the way when the brake fluid is low and I assume they share the same fluid. I'm going to take it to my mechanic but could this be a clutch problem or just a fluid leak.
View 1 Replies